How is a lubricant drop be broken into finer droplets of a mist ? a. By increasing its kinetic energy by vibrating it at high frequency b. By placing the drop into a zone of low pressure which is less than the internal pressure of the drop, generated by a venturi. c. By evaporating the drop into molecular form by reducing its pressure. d. By placing the drop into a highly turbulent zone such that a number of air jets blown onto it shears it into fine droplets of a mist.

How is a lubricant drop be broken into finer droplets of a mist ? a. By increasing its kinetic energy by vibrating it at high frequency b. By placing the drop into a zone of low pressure which is less than the internal pressure of the drop, generated by a venturi. c. By evaporating the drop into molecular form by reducing its pressure. d. By placing the drop into a highly turbulent zone such that a number of air jets blown onto it shears it into fine droplets of a mist.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.46P

See similar textbooks

Similar questions

Air in an automobile tire is maintained at a pressure of 220 kPa (gage) in an environment where the atmospheric pressure is 94 kPa. The air in the tire is at the ambient temperature of 25°C. A 4-mm-diameter leak develops in the tire as a result of an accident. Approximating the flow as isentropic determine the initial mass flow rate of air through the leak.
You are pouring heavy syrup on your pancakes. As the syrup spreads over the pancake, would the thin film of syrup be a laminar or turbulent flow? Explain.
You are designing an IC heatsink which uses round pins in cross-flow. The heatsink must dissipate 3000W. The heatsink has 10 rows of 8 columns of round pins with a diameter of 1mm. The pins have longitudinal and transverse pitch of 6mm. The incoming air is at 25oC with a velocity of 3 m/s. Assume fluid properties are constant. If the pins are arranged in-line: a) Find the Reynold’s Number b) Find the Nusselt Number c) If the pins are 30mm tall, how hot must the pin surface be (average) to dissipate the proper amount of heat?
ANSWER this, please.With the formula derived and the conditions applied in problem statement # 1, calculate for the heavier liquidoverflow leg, the diameter, and the volume of the tank in separating liquid B from liquid A having densities of 1278kg/m3 and 794 kg/m3, respectively. The volumetric flow rate of the mixture entering the tank is 30 m3/hr and the viscosity of the lighter liquid (continuous phase) is the same as the viscosity of water @ 35oC. Volume of heavier liquid is twice the volume of the lighter liquid and having a tank diameter to height as 1:2 ratio. Assume for 10% from the tank volume allotted for the vapor space having a pressure of 50 kPa. REFERENCE: (problem 1) Derive a formula to calculate for the height, ZC of the heavier liquid overflow leg in a continuous vertical cylindrical decanter. The pressure at the discharge point of the heavier liquid is given as 90% of the pressure on top of the fluid mixture. Express the height of the heavier liquid as ZB and the…
4.2. The ball catathermometer factor (F) is 620, time while the spirit column drops from 38 to 350C in 100 seconds and the air temperature is 260C. Determine the air movement speed for the industrial section with these parameters.
A 30mm ID, 50mm OD aluminum round tube passes air through it at a rate of 0.08 m^3/s. A 100W electric heater blanket covers the outside of the 2m long tube. If the air enters the tube at 100 celsius , what temperature does it exit at? Assume that the heater blanket is perfectly insulated on the back side (no heat loss out the back). Note-RT is 25 celsius
For using lotion, sketch a diagram of what would be consider the control volume used in understanding the in/out flows as well as accumulation (or losses) of the different properties with a control volume (i.e. mass, momentum, energy). Be sure to identify when fluid would have zero and non-zero velocities crossing the fully enclosed control surfaces.
. Two identical tanks of large area contain different fluids. Both of them has ahole of the same height from the top, but the cross sectional area of the first tankis half of that of the second tank.a. What is the ratio of the densities of the two fluids if the mass flow ratethrough the holes is equalb. What is the ratio of the volume flow rate through the holes of the tanksc. For an equal volume flow rate from the two holes, what should be theratio of the depth of the holes.
What makes turbulent mixing complicated?A. The Reynolds number cannot be calculated when the flow is turbulent.B. The large eddies formed during mixing is part of the distorted laminar fluid elements.C. Low frequency velocity fluctuations contribute to the complexity of such analysis.D. There are no available correlations that can relate the Reynolds number and friction factor.
Elaborate and explain the piping equipments in cryogenic plant including the pipes and fittings, valves, filters, pressure regulators, expansion joints, strainers.
A horizontal axis wind turbine with a 20-m diameter rotor is 30% efficient at 10 m/s winds and at 1 atm of pressure and 15° C. (a) How much power would it produce at these conditions? (b) What would the air density be on top of a mountain at an elevation of 2500 m at 10° C? (c) Determine the power the wind turbine would produce on the mountain with the same wind speed. Assume that the efficiency of the turbine is not affected by density. Is it beneficial to build the turbine on top of the mountain? Explain your answer.
The capillary pressure for a channel of round cross section can be expressed as a function of the surface tension, the contact angle and the channel radius (the numerical factor is 2). Assume a transition of two coaxial channels of constant round cross sections. The larger one has a diameter of 2 mm and a contact angle of 80 degree, the narrower one a contact angle of 125 degree with the liquid. Calculate the other radius required so a liquid segment having one of its two menisci within either segment experiences a counter pressure of 15 mbar.