Answered: How much mass of cement required if the…

Engineering

Civil Engineering

How much mass of cement required if the volume of cement need to create 1.0 m3 of concrete is 0.135 m3

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter11: Pricing Concrete Work

Section: Chapter Questions

Problem 4RQ

See similar textbooks

Related questions

Q: 500 Ibs J000 Ibs 4 3 10' 10' Determine the magnitude and direction of the resultant of the force in ...

Q: A stone is thrown vertically upward from the ground with a velocity of 48.3 ec. One second later, an...

Q: Using virtual work methed Draw B.M.D2 4m

Q: gravity dam of trapezoidal cross section with one face vertical and horizontal base is 22m high and...

Q: A vertical curve with a length of 260 m is used to connect a 2.5 % and-2.5% gradients with a PVC at ...

A: This question is related to the Vertical Curve form Surveying Engineering.

Q: 1) Determine the elevation, pressure, and total hydraulic heads at all points, a through g using Dat...

A: Given data:

Q: Q3 [25 p). Water in a horizontal channel accelerates smoothly over a bump and then undergoes a hydra...

Q: Draw S.F.D and B.M.D 50 KN/m 20 kN/m 100 KNm 3 m 3m 1m 6m

Q: A square footing is 1.8 x 1.8 m² with a 0.4 x 0.4 m? square column. It is loaded WILH AA zria! Joad ...

Q: of cement to civil/structural engineers in the field especially with extreme weather conditions? Ela...

A: The soundness of cement relates to the consistency of volume change during the setting and hardening...

Q: The ratio of saturted unit weight to dry unit weight is 1.23. If specific gravity is 2.7. The void r...

A: Given data : Specific gravity (G)=2.7 Dry unit weight=γDry Saturated unit weight=γSat γSatγDry=1.23 ...

Q: Situation 1 | A built-up beam made from fastening two channels to a wide flange section carries load...

Q: The shear-force diagram for a simple beamis shown in the figure.Determine the loading on the beam an...

A: Given data:

Q: Number of road accident on a road in a month follows Poisson's distribution with mean 0.27. The prob...

A: Given data, Mean =0.27

Q: A simple beam AB supports two connectedwheel loads 3P and 2P that are a distance d apart (seefigure)...

A: Given:- P =12 kN, d = 2 m, and L =15 m To find:- (a) Determine the distance x that will produce t...

Q: b 2 m 3 m V 12 kN 4@4 m = 16 m %3D

Q: During the determination of the shrinkage limit of a sandy clay, the following data were obtained. W...

Q: The loads which include the weight of the structural material and the stored products are called : a...

Q: The channel section shown in the figure below has the shape factor of 90 mm - 7.6 mm 13.6 mm 300 mm

A: Given data,

Q: The required structural number over the base SN, is equal to 3.2 and the layer coefficient for an as...

Q: Given: Instrument @ "B", BS "C", FS "A" Northing B = 5000.000, Easting B = 10000.00, Elevation B = 5...

Q: A cantilever beam AB of length L = 6.5 ft supportsa trapezoidal distributed load of peak intensity q...

A: Given:- L=6.5ft σallow =18 ksi τallow = 7.5 ksi To find:- the maximum permissible load q based upo...

Q: What will be max. height that the water tank that may become full if the max. tangential stress is S...

Q: A shallow continuous foundation is to be constructed on a soil under the ground' surface as shown in...

A: INTRODUCTION: Bearing capacity of soil: It is the strength or ability of soil to sustain the load ac...

Q: A built-up beam made from fastening two channels to a wide flange section carries loads` as shown. T...

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three subpa...

Q: A 100-m tape with a density of 7700 kg/m³ and a cross-sectional area of 2.6 mm? is used to measure a...

A: For pull correction to be zeroP-PsLAE=0so,P=PsLAE

Q: SITUATION: A wide flange section has a length of 10 m. The properties of the section are d= 250 mm (...

A: Given data: Effective length (LO)=10mDepth of beam=250mmThickness of web tw=9mmWidth of flange=250m...

Q: The required structural number over the base SN, is equal to 3.2 and the layer coefficient for an as...

Q: Determine the design flexural strength in ft kips of a W12 x 35 of A242 (Fy = 50ksi) steel subject t...

Q: What is the depth of water in a trapezoidal channel with z=2 and carrying a 2.5 m3/s water flow? The...

Q: The tapered cantilever beam AB shown in thefigure has a solid circular cross section. The diametersa...

A: Given:- d=(dA/L)(L+x) I = (πd4/64) = (πd4A/64L4)(L+x)4 = (IA/L4)(L+x)4 To find:- The equation of th...

Q: 2 A flotation plant treats 5,000 tonnes of ore per hour on a dry basis. For optimum flotation effici...

A: Given, Flow rate of ore = 5000 mtph Density=2.75 t/m3 Volume of each cell=100 m3 Time= 40 min

Q: A well in an unconfined aquifer was pumped at a rate of 900 m³/day. Drawdown was measured in a fully...

A: Given, Flow rate (Q) = 900 m3/day Radial distance (r) = 85 m

Q: Instructions: Solve the following problems completely using Method of Consistent Deformation. 25 kip...

Q: A pressure gage 6m above the bottom of the tank containing a liquid reads 90kPa. Another gage height...

Q: Knowing that w is 170 Ib/ft, determine the internal moment in the beam at point C using the sign con...

A: We will calculate reactions at A and B .

Q: A rigid bar of weight W = 800 N hangs from three equally spaced vertical wires (length L =150 mm, sp...

A: Given:- W=800N Es = 210 GPa and Ea = 70 GPa da = 4 mm L =150 mm, spacing a = 50 mm To find:- (a) Wha...

Q: under the embankments at point A that are loaded at a depth of 4 m below the ground Tuo embankments ...

A: The values and diagram given in the question are as follows: Unit weight of left embankment(γ1)=11 k...

Q: elevation 1035.3 m. The location of the highest point on this curve in m from PVC is about The eleva...

Q: Given the following data: Slump Requirement 4" Max. Aggregate Size 1.0" %3D Mass of water = 193 kg/m...

Q: 1.5m 0.70 H20 Sand 1.2 e=0.50. A 1.0 B valve оpen flow

Q: ve with a length of 260 m is used to connect a 2.5 %o and -2.5 %/o gradients with a PVC at an elevat...

Q: Section 4.4. 3. Draw the shear and moment diagrams for each member of the frame. Assume A is fixed, ...

Q: Quickly find support reaction

A: Given data : The value of Point load P=4 KN The value of uniformly distributed load q=2 KN/m To fi...

Q: A rock is thrown horizontally from a cliff 110 ft high. The initial velocity is 204 How far from the...

Q: Summarize the difference between soundness test by Le Chatelier method and Autoclave method. DIFFERE...

A: Soundness test- Certain cement has been discovered to have a considerable expansion after setting, l...

Q: While aligning a high way in a built up area, it was necessary to provide a horizontal circular curv...

Q: Q4 In the following figure shows a channel contraction section often called a venturi flume, because...

Q: A reducer bend having an outlet diameter of 15 cm discharge freely. The bend, connected to a pipe of...

A: Given data : outlet diameter=15cm inlet diameter=20cm angle of deflection=60 degree (in vertical pla...

Q: SITUATION 1: A pre-stressed concrete pile of length L is to be picked up by crane at two points, bot...

A: Due to the loading in the pile no cracking will be form hence the positive bending moment at mid of ...

Concept explainers

Pricing Concrete Work

The concrete work in a project usually holds a high-end cost in terms of cost and value of the work. It becomes an important step in calculating the cost associated with concrete while preparing the project scale. The cost of making concrete depends on the cost of building materials, mixed materials, labor, and machinery. A concrete contractor builds structures from concrete, usually managing all the steps of the process from assembling ingredients to building a holding structure and preparing the mixture. This person or team oversees the delivery and unloading of goods to ensure that they are done properly. Nowadays, most of the concrete in the United States comes from manufacturers working abroad, usually with branches and plants within the provinces. Contributions can range from pre-mixed concrete to basic ingredients, the consumer company then mixes it. Many American-based concrete companies, however, offer concrete products, such as ballads, bricks, countertop, concrete pipe, and building products, as well as concrete construction and installation materials. This article covers both types of suppliers for this set of building materials.

Question

How much mass of cement
required if the volume of
cement need to create 1.0 m3
of concrete is 0.135 m3

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

how much mass of water required if the volume of cement needs to create 1.0 m3 of concrete is 0.140 m3 and water/cement ratio = 0.48?
A batch of concrete consisted of 200 lbs fine aggregate (sand), 400 lbs coarse aggregate(gravel), 95 lbs cement, and 5 gallons of water. The relative density of the sand and gravel may be taken as 0.65 and that the cement as 3.10 What was the total volume ofconcrete produced? FULL solution please thank u
REQUIREMENTS: CONCRETE MATERIALS (CLASS A) -bags cement -m° sand -m° gravel -gallons water
Given : Width = 1.00m Length = 2.50m Cement = 50kg/bag Using Class A concrete mixture, what is the volume of sand, cement, gravel and water needed?
A batch of concrete consisted of 200 lbs. fine aggregate, 350 lbs. coarse aggregate, 94 lbs., cement and 5 gallons water. The specific gravity of sand and gravel may be taken as 2.65 and that of the cement as 3.10. How much by weight of cement is required to produce one cubic yard? Final answer must be in pounds.
A batch of concrete consisted of 200 lbs fine aggregate (sand), 400 lbs coarse aggregate(gravel), 95 lbs cement, and 5 gallons of water. The relative density of the sand andgravel may be taken as 0.65 and that the cement as 3.10 What was the total volume ofconcrete produced?
A batch of concrete consisted of 200200 lbs. fine aggregate, 350350 lbs coarse aggregate, 9494 lbs cement, and 55 gallons water. The specific gravity of the sand and gravel may be taken as 2.652.65 and that of the cement as 3.103.10. What was the weight of concrete in place per cubic foot? How much by the weight of the cement is required to produce one cubic yard?
(a) Calculate build-up rates for cement mortar mix (1:1:6) by using a machine size 7/5 per m3 (b) Calculate build-up rates for one brickwork in common bricks in cement, lime, and sand (1:1:6) mortar in Flemish bond, non-load bearing per m2(Price of mortar is based on the answer of Q3(a)).
Two batches of cement mortar with properties as shown in Table P6.18. Ifmortar cubes are made from these batches, which batch do you expect to havelarger compressive strength? Why?
Discuss the cement manufacturing process on the basis of the equipment and process diagram
**PLEASE ANSWER IT AND SHOW YOUR WORK STEP-BY-STEP** Determine the quantities of materials required per cubic yard to create a concrete mix. The specifications require a maximum size aggregate of 1½ in., a minimum cement content of 5½ sacks per cy, and a maximum water-cement ratio of 0.63. Assume 5% air voids.
Estimate the total amount of cost for concrete works (class “B”) based from the following given: 10-pcs of F1 (1.2m x 1.2m x 0.3 m) 10-pcs of C1 (0.3 m x 0.3 m x 4.1 m) Floor area of 100mm thk slab-on-grade = 53 sq.m The cost of cement (40kg per bag) = 210 per bag. The cost of sand is 710 per cubic meter. The cost of gravel is 1900 per cubic meter.