How much will a steel bar's elongation by a load of 12 kips if the bar is 12 ft in length w/ cross-sectional area of 0.5i n ^ 2 A. 0.011 ft B. 0.15-inch C. 0.35 cm D. 2.93 mm Compute the shear strain if the shear stress of a material is given to be 6000 psi and its shear modulus of elasticity is 86 GPa. A. 2.41 x 10 ^ - 4 B. 6.14 x 10 ^ - 3 C. 4.81 x 10 ^ - 4 D. 8.17 x 10 ^ - 4

How much will a steel bar's elongation by a load of 12 kips if the bar is 12 ft in length w/ cross-sectional area of 0.5i n ^ 2 A. 0.011 ft B. 0.15-inch C. 0.35 cm D. 2.93 mm Compute the shear strain if the shear stress of a material is given to be 6000 psi and its shear modulus of elasticity is 86 GPa. A. 2.41 x 10 ^ - 4 B. 6.14 x 10 ^ - 3 C. 4.81 x 10 ^ - 4 D. 8.17 x 10 ^ - 4

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter4: Mechanical Processes

Section: Chapter Questions

Problem 4.20P

See similar textbooks

Similar questions

A 30m steel tape weighing 1.45kg is of standard length under a pull of 5kg, supported for full length. A line 938.55m long was measured using the tape with a steady pull of 10kg. If E=2.0x106kg/cm2 and unit weight of steel is 7.9x10-3kg/cm3, determine: a) cross-sectional area of the tape b) CP c) Correct length of line
Three planks of wood were joined together to form the T-section shown in figure A. The beam is the subjected to a maximum shearing force of 60 kN. 1. Find its moment of Inertia a. 11.573 x 10⁶ mm ⁴b. 10.573 x 10⁶ mm ⁴c. 12.573 x 10⁶ mm ⁴d. 13.573 x 10⁶ mm ⁴2. Find the shearing stress at the neutral axis a. 3.28 MPab. 3.48 MPac. 3.39 MPad. 3.89 MPa3. Find the shearing stress at the junction of the T-section. a. 3.8 MPab. 3.59 MPac. 3.35 MPad. 3.18 MPa
Work out the quantity of steel in a 7m long simply supported beam of size 350 X 600mm overall. Bottom bar: 4 – 12mm diameter straight bars. Anchor bar: 2 – 12mm diameter straight bars, stirrups 10mm diameter @ 250mm c/c throughout the length of the beam. Clear cover as 25mm on all sides.
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee A w24 X55 is used as a beam with a length of 6m. The beam is supported by a bearing plate of 300 mm x 200 mm x 30 mm on the wall having a thickness of 250 mm.Properties: d=598.68mmbf = 177.93 mmtw =10.03mm k=33.34 mmtf = 12.83mmFy = 250 MPaQuestions:1. Determine the design strength for web local yielding.2. Determine the design strength for web crippling.
A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional area of A1 = 0.30 in.2 and a length of L1 = 115 in. Bar (2) has an area of A2 = 0.30 in.2 and a length of L2 = 130 in. Bar (3) has an area of A3 = 0.20 in.2 and a length of L3 = 35 in. The loads and angles are P = 29 kips, α = 37°, Q = 10 kips, β = 55°, and R = 14 kips. Determine the vertical deflection of end A. Consider a free body diagram that cuts through member (1) and includes the free end of the bar. Calculate the internal force and the deformation that occurs in member (1). Tension and elongation are positive, while compression is negative.
A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional area of A1 = 0.35 in.2 and a length of L1 = 120 in. Bar (2) has an area of A2 = 0.35 in.2 and a length of L2 = 90 in. Bar (3) has an area of A3 = 0.20 in.2 and a length of L3 = 45 in. The loads and angles are P = 29 kips, α = 32°, Q = 11 kips, β = 57°, and R = 14 kips. Determine the vertical deflection of end A. A downwards deflection is positive, while an upwards deflection is negative.
The main beam of UB 610 x 229 x 101 kg/m in steel grade S275 supportssecondary beamsof UB 406 x 140 x 39 kg/mon its top flange.The schematic diagram of the floor supported by the beams is presented in Figure 1. c) Check the cross-section classification of the main beam. 4xxx= 4715 1xxx= 1715 50xx= 5015
To reinforce a column in an existing structure, two channels are welded to the W 12 x 50 column section as shown in the figure. Effective length of column with respect to each axis is 4.8 m. Kx = Ky = 1.0 Properties of W12 x 50 A = 9484 mm2 rx = 131.57 mm ry = 49.78 mm Ix = 164 x 106 mm4 Iy = 23 x 106 mm4 Fy = 345 MPa d = 309.63 mm Properties of C6 x 13 A = 2471 mm2 Ix = 7.24 x 106 mm4 Iy = 0.44 x 106 mm4 bf = 54.79 mm x = 13.06 mm (centroid from the outer side of the web) a. Determine the critical slenderness ratio. b. Determine the design strength of the column section. (kN in LRFD)
Please do both qestions Q1 - Inner diameter = 47.0 mm Q2 - Inner diameter = 12.6 mm
Refer to the photo provided and please make sure your handwriting is readable. L1 = 2.02 m L2 = 1.21 m H= 3.03 m Width of plate hanger = 40.04 mm Thickness of plate hanger = 10.01 mm Bolt diameter = 20.02 mm Allow shear stress of the bolt = 68.08 MPa Allow bearing stress of the bolt = 240.04 MPa 1. What is allowable stress in the hanger based on the bolt capacity in double shear at D 2. If maximum tensile stress in the hanger is 140 MPa. Find allowable W. 3. If W is 60 kN, find the maximum displacement.
A line is recorded as 472.90 m long. It is measured with a0.65 kg tape which is 30.005 m long at 20 °C under a 50N pull supported at both ends. During measurement, thetemperature is 5 °C and the tape is suspended under a 75N pull. The line is measured on 3% grade. E = 200 GPa,cross-sectional area of tape is 3 mm2 and the coefficientof linear expansion is 0.0000116 /°C. Compute:a. The actual length of tape during measurement.b.The total error to be corrected for the inclined distancec.The true horizontal distance
A 30-m steel tape standardized at 20°C and supported throughout under a tension of 5.45 kg was found to be 30.012-m long. The tape had a cross-sectional area of 0.050 cm2 and a weight of 0.03967 kg/m. This tape was held horizontal, supported at the ends only, with a constant tension of 9.09 kg, to measure a line from A to B in three segments.The modulus of elasticity E = 2.10 x 10^6, and the data listed in the following table were recorded. Apply corrections for tape length, temperature, pull, and sag to determine the correct length of the line.