How thick must the insulation layer be to achieve the requirement U = 0.18 W/m2K? A wall of ventilated facade with insulation must meet requirements: Bearing construction: Lightweight concrete λ lightweight concrete = 0.14 W/mK, d=100 mm λ insulation = 0.04 W/mK, d=? etc Cold bridges 15% Guide to task 1: 1) The requirement for the U-value with regard to cold bridges will be U - 15%. 2)Ri for walls: 0.13 m2K/W Ru for walls: 0.04 m2K/W

How thick must the insulation layer be to achieve the requirement U = 0.18 W/m2K? A wall of ventilated facade with insulation must meet requirements: Bearing construction: Lightweight concrete λ lightweight concrete = 0.14 W/mK, d=100 mm λ insulation = 0.04 W/mK, d=? etc Cold bridges 15% Guide to task 1: 1) The requirement for the U-value with regard to cold bridges will be U - 15%. 2)Ri for walls: 0.13 m2K/W Ru for walls: 0.04 m2K/W

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter2: Municipal Solid Waste Characteristics And Quantities

Section: Chapter Questions

Problem 2.10P

See similar textbooks

Similar questions

Steel forms will be used to cast a 12 in. thick wall in cold weather with concrete containing 300 lb/ydl ofType I cement. The wall will be wrapped with a 2 in. thick blanket made with mineral fiber insulation. Assuming linear interpolation is appropriate, what is the minimum acceptable surrounding ambient temperature for 3 days curing without providing additional protection?
Solve for what is being required. Room dimensions are: LxWxH = 8.50 m, 5.0 m, 3m. Originally, the room had linoleum flooring with an absorption coefficient of 0.03. Two opposite walls were cladded with unglazed bricks with an absorption coefficient of 0.02, the one having the entrance gypsum door (2.1 m X 0.80 m) with 0.05 abs.co.; the other two were just bare concrete with sliding glass window openings of 1.80m x 1.20 m each; the bare concrete with an abs.co. Of 0.31 and the window glass with 0.18, the ceiling, too , had bare concrete as its finish at 500 Hz. The client would like to renovate the space into an acoustical studio room and would like to change the ceiling and the flooring. The ceiling will have a vinyl faced fiberglass panel with an abs.co. of 0.71, and the floor will have mineral fiber tiles with an abs.co. Of 0.66, all at 500 Hz.
Assuming you apply 5/8” coating of gypsum wallboard to the non-fire exposed side of a 6” thick siliceous concrete wall, what is the new effective thickness to be used to determine the resistance of the wall?
A wide-flange WF 24 x 76 steel beam with 1 in. (25.4 mm) of spray-applied cementitious material (British equivalent 610 x 229 x 113 kg/m). The beam has WID 1.03 lb/ft and nowhere does the temperature exceed 1,000 F (538 C) or 811 K. The insulation temperature is to he 750 F while keeping the steel temperature at 538 C. The results obtained from (a) Malhotra's quasi-steady state approach (b) Jeanes' graph (c) Lie's graph are compared. To calculate the fire resistance R for the spray-applied beam, the following data are used:
Answer ONLY items 5-8. Room dimensions are: LxWxH = 8.50 m, 5.0 m, 3m. Originally, the room had linoleum flooring with an absorption coefficient of 0.03. Two opposite walls were cladded with unglazed bricks with an absorption coefficient of 0.02, the one having the entrance gypsum door (2.1 m X 0.80 m) with 0.05 abs.co.; the other two were just bare concrete with sliding glass window openings of 1.80m x 1.20 m each; the bare concrete with an abs.co. Of 0.31 and the window glass with 0.18, the ceiling, too , had bare concrete as its finish at 500 Hz. The client would like to renovate the space into an acoustical studio room and would like to change the ceiling and the flooring. The ceiling will have a vinyl faced fiberglass panel with an abs.co. of 0.71, and the floor will have mineral fiber tiles with an abs.co. Of 0.66, all at 500 Hz.
A room in a single-story building has three 2.5 x 4 ft double-hung wood windows of average fit that are not weather-stripped. The wind is 23 mph and normal to the wall with negligible pressurization of the room. Find the infiltration rate, assuming that the entire crack is admit ting air.
A cold-storage warehouse is to be constructed of a number of individual rooms that are maintained at various temperatures. The walls of one room are constructed of 4 inches thick masonry on the outside of 0.5 inches thick plywood on the side. Sandwiched between the masonry and plywood is glass fiber insulation that is 3.5 inches thick. The inside-wall temperature is to be maintained at −10°F and the outside-wall temperature is 70°F. As a first step in sizing the required cooling unit, determine the heat flow the wall on a per-square-foot basis.
Urgent..... Classify the following materials with regard to their thermal insulation properties, rate them from the best to the worst: Solid concrete block, Burned clay block, clay brick. Cement - sand bricks, light weight blocks, and hollow concrete blocks.
Select appropriate types of insulation for various applications in the design of a building.?
Discuss the three positions in which thermal insulation may be installed in a low-slope roof, and the advantages and disadvantages of each.
Explain the structutre of Insulation Between the Roof Deck and the Membrane.
A restaurant wants to change the design of a dining room. One of its solidwalls is being replaced with a fixed double pane glass wall. The designtemperature difference is 70°F. The wall measures 9 feet high and 20 feet 6inches long. It was a brick wall with 31⁄2 inches of insulation. What will be theadditional heat load for the ventilation system during the winter due to thiswall?