HW #7 I. Solve the problems below using the Moment Area method. Find AA: A sk 2' 4¹ 6K 3'

Q: Obtain the cross-sectional effects of the beam given in the figure by the cutting method. Draw shear…

A: AA

Q: Q2. A tie member of a roof truss consists of two angles are connected to either side of a gusset…

A: Working load= 350kNFactored load= 350kN=525kNHence each angle carries a factored pull of kN

Q: Some waste has a five-day BOD (biochemical oxygen demand) at 20 oC , equal to 210 mg/L and an…

A: Given data, five-day BOD (biochemical oxygen demand) at 20 oC , equal to 210 mg/L ultimate BOD…

Q: 2. The cantilever retaining wall resists active lateral earth pressure throughout its length. Given:…

A: Retaining walls are used to support soil laterally to retain it at different levels or of poor…

Q: The beam shown is made up of W840 x 193 (Fy = 248 MPa) and is 8m long. The bearing length at the…

A: The maximum value of P so that the member is safe against web yielding is given by:Pwy = 2 * Fy * tw…

Q: t, the moment developed at fixed end is

A:

Q: Which among the following air pollutant is not present in an auto exhaust gas CO₂ NOX Peroxyacetyl…

A: This question is related to the Air pollution from Environment Engineering from Civil…

Q: What is the meaning of Sanitary Engineering ?

A: Sanitary engineering is a specialized branch of civil engineering that involves designing,…

Q: A community has an expected future population p= 180400 capita after dt= 23 years and a present…

A:

Q: A road with 4.5% upward grade has a design speed of 90kmph, if coefficient of longitudinal friction…

A: To determine the sight distance ,Sight Distance = (V2/2g * f) + (V * t)where:V = Design speed = 90…

Q: *6-40. Determine the force in members CF, FG, and GC of the truss and state if the members are in…

A:

Q: 8-7. Determine the vertical displacement of joint A. Each bar is made of steel and has the…

A: Note:-As per our company guidelines I am solving the problem with above mentioned method only.( i.e…

Q: structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries…

A:

Q: Estimate the water demand for a city of 100,000 people. Assume the annual average consumption rate…

A: number of people=100000annual average consumption rate=647Lpcd

Q: A bent pipe is attached to a wall with brackets as shown. A force of F= 210 lb is applied to the end…

A:

Q: Consider the bid rent curve (R) for the office sector (OS) and household sector (HH). Allow for both…

A: Bid-rent curves are graphical representations of the relationship between the rent (price) of land…

Q: The axially loaded column given in the following image is a W14x53 with L = 7.8 m: Calculate the…

A: The axially loaded column given in the following image is a W14x53 with L = 7.8 mOur aim is to…

Q: A W250 x 167 section is used as a column of hinged ends with a length of 6m. To what extent along…

A:

Q: Calculate angular frequency of a cantilever beam of span 2.5 m O69.87 rad/sec O 74.70 rad/sec O47.58…

A:

Q: Draw the shear and bending-moment diagrams for the beam AB, and determine the maximum absolute…

A:

Q: A canal has a flow rate ranging between 0.1-0.2 m3/sec through a v-notch weir. Determine the max…

A:

Q: Determine the maximum safe capacity of an axially loaded hinged ends column having an unsupported…

A: A1 = 2500 sq mm A2 = 3750 sq mm Both ends are hinged, with unsupported length= 4m Yield strength= fy…

Q: 15 ft E |--12A-12 ft- B G 20 kips H ←12 ft→ 12 ft→12 ft· D

A:

Q: The 1.25-in.-diameter bent rod is subjected to the load F = {330i +325-2502} lb Part A Determine the…

A: D = 1.25 in F = (330i+325j-250z) lb Find out - Determine the maximum torsional stress in the rod at…

Q: 3-Calculate ultimate bearing capacity of the following square footing using Weigthed Average Method…

A: To use the weighted average method, we first need to calculate the bearing capacity of each layer of…

Q: Compute for the value of: Average Moment of Inertia Moment of Inertial about the Y-axis = 0.667 x…

A: Given data - Ix = 2.667×106 mm4 Iy = 0.667×106 mm4 Ixy = 1×106 mm4  Find out - Average moment of…

Q: Use the moment-area method to determine the slopes and deflections at points B and C of the beams…

A: "Since you have posted multiple questions, I will solve first for you as per guideline"

Q: Problem 3: Kitchen Faucet A faucet discharges a 0.50 in diameter stream of water at 12.8 ft/s. What…

A:

Q: Compute the elastic settlement for a rigid 10 ft by 15 ft footing loaded with 4000 psf uniformly…

A:

Q: R (D,0) (B, -C) Fº (A,C) (E,0) ⠀ Moment of Inertia about the X-axis = 2.667 x 105 mm², Moment of…

A: Given:Ix = 2.667*106 mm4Iy = 0.667*106 mm4Ixy = 1.000*106 mm4Required:Maximum and minimum moment of…

Q: For a trapezoidal channel with base width b = 6.0 m and slope z = 2. calculate the critical flow tie…

A:

Q: 6-33. Determine the force in members BC, HC, and HG of the bridge truss and state if the members are…

A: Determine the force in members BC, HC and HG of the truss.Let's using method of section.

Q: Let average yearly evapo-transpiration and average yearly rainfall are 250 cm and 300 cm…

A:

Q: Problem 5: Snowmobiles, Ice, and Water What is the minimum speed to avoid sinking when using a…

A:

Q: what are your feedback on water resource track relate to the civil engineering practice.

A: The water resources track in civil engineering practice is an important and growing field. Water…

Q: 3. The compound beam given in the figure is composed of a pair of beams, AB and BC, connected by a…

A:

Q: ease discuss the effect of Pollution on Lake

A: Water pollution occurs when harmful and undesirable substances are introduced into it, causing a…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: By Using Unit Load Method, Calculate the total deflection at joint B. Members have the same moment…

A: Given:P = 153 kNRequired:Deflection at B

Q: Water is pumped up from a reservoir to a smaller holding tank. If the flow rate through the pipe is…

A: NPSH is the net positive suction head, which is measured in the centrifugal pump.If the local…

Q: a) Discuss the principal/primary contractual roles of the client and contractor under the…

A: Under conventional construction contracts, there are generally two primary parties involved:the…

Q: The two spheres A and Beach have a mass of 400 g. The spheres are fixed to the horizontal rods as…

A: The initial velocity of the spheres, vo = 2 m/sThe mass of each sphere, m = 400gmThe couple moment,…

Q: Determine the Moment of Inertia about the X' axis if angle between X' and Xo is 30.1 degrees…

A:

Q: A pumping machine in the water lifting station is found to produce a sound level of 50 dB. During…

A:

Q: Uniform flow is taking place in a rectangular concrete channel (n= 0.013) with a bottom width of 3 m…

A:

Q: 1. The three reservoirs A, B and C are connected by pipelines 1, 2 and 3, respectively. The…

A: Three reservoirs A, B, C are connected by pipeline as shown in the figure. The length, diameter,…

Q: Critical duration ? 22 P 17 days 18 days O 16 days 15 days ( 3 R 4 S 50/3 3 10 5 U 3 2

A: Determine the critical duration of the project.

Q: 1. The figure shows a frame with negligible mass, keeping a 50-lb weight in equilibrium. The smooth…

A:

Q: A rectangular channel carries a flow of 10 cfs/ft of width. Plot a curve of specific energy vs…

A:

Q: A rectangular channel has a bottom width of B = 18 m, a Manning's roughness of n = 0.013 and a…

A: bottom width B0=18mn=0.013S0=0.0005yn=1my=0.78m