HW24 11.73 A 240-V ms 60-Hz supply serves a load that is 10 kW (resistive), 15 KVAR (capacitive), and 22 KVAR (inductive). Find: (a) the apparent power (b) the current drawn from the supply (c) the KVAR rating and capacitance required to improve the power factor to 0.96 lagging (d) the current drawn from the supply under the new power-factor conditions

HW24 11.73 A 240-V ms 60-Hz supply serves a load that is 10 kW (resistive), 15 KVAR (capacitive), and 22 KVAR (inductive). Find: (a) the apparent power (b) the current drawn from the supply (c) the KVAR rating and capacitance required to improve the power factor to 0.96 lagging (d) the current drawn from the supply under the new power-factor conditions

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.17P: Consider a load impedance of Z=jwL connected to a voltage and V let the current drawn be I. (a)...

See similar textbooks

Similar questions

Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
An AC generator having an internal resistance of 2 k*(omega) is connected to an LCR circuit in series as shown in the figure. If the generator supplies an electromotive force, E = 282 sen (100*pi*t) volt, calculate:a) the impedance of the circuitb) the rms value of the current in the circuitc) the voltage drop across L, C and R
An investor own two large stores at Dubai. Both malls are connected in parallel and operating at an unknown voltage. The local utility system voltage is 13.8 kVrms and supplied power to the malls through a feeder line with impedance equal to 1+j2.5 ohms. Store 1 is consuming 400 kW at 0.8 pf lagging while Store 2 is consuming 300 kVAR at 0.75 pf lagging. Determine the following: a) The stores' operating rms voltages. b) The total real and reactive power of the ehole system. c) The overall pf of the whole system.
five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let R= 200, L=0.400H,C=6.0 Mf, and V=30.0 v. what's the reading of the voltmeter's V1,V2,V3,V4 and V5 if W= 200 rad/s
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
The two loads shown can be described as follows: Load 1 absorbs an average power of 60 kW and delivers 70 kVAR of reactive power; Load 2 has an impedance of (24+j7) Ω. The voltage at the terminals of the loads is 25002 cos 120π t V.1. a) Find the rms value of the source voltage.2. b) By how many microseconds is the load voltage out of phase withthe source voltage?3. c) Does the load voltage lead or lag the source voltage?
A residential electric power monitoring system ratedfor 120-V rms, 60-Hz source registers powerconsumption of 1.2 kW, with a power factor of 0.8.Finda. The rms current.b. The phase angle.c. The system impedance.d. The system resistance.
Suppose the circuit shown represents a residential distribution circuit in which the impedances of the service conductors are negligible and Vg1=Vg2=120 0° V (rms). The three loads in the circuit are L1 (a new refrigerator, a coffee maker, and a microwave oven); L2 (2 incandescent lamps, a humidifier, and a ceiling fan); and L3 (a clothes washer and a clothes dryer). Assume that all of these appliances are in operation at the same time. The service conductors are protected with 20 A circuit breakers. Will the service to this residence beinterrupted? Why or why not?
A network is supplied by a 120 V rms, 60-Hz voltage source. An ammeter and a wattmeter indicate that 12 A rms is drawn from the source and 800 W are consumed by the network. Determine: a. The network power factor b. The network phase angle c. The network impedance d. The equivalent resistance and reactance of the network
An example power system has two distinct manufacturing areas, one with harmonic loads, and another with only linear loads. The portion of the system with the harmonic loads draws 75 A rms at 60 Hz, 10 A rms at 300 Hz, and 5 A rms at 420 Hz. The part of the system with only linear loads draws 75 A rms at 60 Hz. (i) What is the total load current (at 60 Hz) if both manufacturing plants are running? Calculate the THD. (ii) What is the total load current (at 60 Hz) if only the manufacturing plant with harmonic loads is running? Calculate the THD.
A source whose voltage is ? (?) = 50√2 cos (?? + 30 °) ? supplies a load of impedance ? = (4 + ?3) Ω. We want to know: a) the active, reactive and apparent power consumed by the load. b) the power of a capacitor that must be installed in parallel with the load to raise its power factor to 0.97 delayed.
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.