I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. INA=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m A |- Im Im->> 3m 3kN/m

I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. INA=410mm 80mm 100mm 60mm 60mm 1.5KN 2kN/m A |- Im Im->> 3m 3kN/m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.8.1P: Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.

See similar textbooks

Related questions

Q: 4. The steel truss that is shown in the Figure below is loaded with three concentrated service live…

A: Factored live load = 200 kNForce on the member is calculated using the Influence line diagram.Member…

Q: Determine the maximum safe capacity of an axially loaded hinged ends column having an unsupported…

A: Unsupported length (L) = 4m or 4000 mmYield strength (Fy) = 248 MPaElastic modulus (E) = 200 GPa or…

Q: A traffic signal control is being designed for a four-leg intersection on a divided highway with the…

A: N-S ApproachesE-W ApproachesMedian width, (ft)1612Number of 12 ft lanes on each approach32Design…

Q: Block Shear The tension member is a PL% x 5% of A242 steel. It is connected to a %-in. thick gusset…

A: PL 3/8 x 5 1/2 A242 steel3/8 in. thick gusset plate, also of A242 steel, with 3/4-inch diameter.To…

Q: 1-Depth of the drains below land surface=1.5 m. 2-Depth of the impermeable layer below land surface…

A: Depth of the drains below land surface =1.5 mDepth of the impermeable layer below land surface =9.5…

Q: You have been given the grid coordinates of two temporary bench marks, A (32143.455 mE, 26623.329…

Q: In the attached image, stresses are acting at a point on the free surface of a stressed body. Here,…

Q: Classify the structures for Stability and determinacy , if unstable state why, if indeterminate…

Q: n emergency spillway for a detention basin is constructed as a trapezoidal channel with bottom width…

A: Trapezoidal channel side slope, 2H:1VManning coefficient, n = 0.040The slope of the channel, S =…

Q: 4. An equal tangent (sag) vertical curve connects an initial grade of -3% and a final grade of +1%…

Q: Consider the following statements related to uplift pressure in gravity dams: 1. A drainage gallery…

Q: The 60-year record shows that the annual maximum discharges for a river have a mean of 30,000 cfs, a…

A: Given dataA 60-year record maximum discharge for river mean of 30000 cfsStandard deviations of…

Q: -2//A/ For the beam shown in Figure (2-A), draw influenced lines for reaction at supports B and F;…

Q: ehicles arrive at an intersection approach at 550 veh/h at the beginning of an effective red and 15…

A: Initial arrival rate: 550 veh/hIncrease rate: 50 veh/h/minSaturation flow rate: 1800 veh/hCycle…

Q: Please show solutions on how to get the 7.85 value. The circle green in the figure.

A: This question is related to the Tension member from Design of Steel structures from Civil…

Q: A single span beam which carries a uniform load of 30kN/m has an unsupported span of 5m. It is made…

A: Uniform loadUnsupported spanCompressive load at centroidWooden sectionAllowable stresses (80% stress…

Q: A material that experiences a force and that deforms as a result of charge building up across its…

A: Piezo electric materials are the type of materials which generate electric charges when they are…

Q: Design a singly reinforced rectangular section to resist a factored moment of 232 K*ft if f'c = 4…

A: Mu = 232 K ftf'c = 4 ksi fy = 60 ksi b = 10 in

Q: Tim (d) Frame T7777 (P) Composite

Q: essure in gravity dams: A drainage gallery reduces the uplift press at all levels below the gallery.…

Q: Draw the normal force, shear force and bending moment diagrams for the following structure.

Q: Briefly describe a reverse curve with tangent in horizontal alignment

A: Reverse curve is comprised of two or more simple curves curving in opposite directions. Its…

Q: Classify the structures for Stability and determinacy , if unstable state why, if indeterminate…

A: In the above two cases, we have to discuss the stability and unstability of the structure. Also we…

Q: A propped cantilever beam (shown in the figure below) is: на с M₁ R₁₁ 1. A Statically indeterminate…

A: Propped cantilever beam:- Is a beam with one end fixed and other end simply supported.

Q: Solve for the external and internal reactions of the structural members shown.

A: NOTE : Since you have asked multiple questions, we will solve the first question for you. If you…

Q: 4. A railway embankment is 10m wide with side slopes 1.5 to 1. Assuming the ground to be level in a…

Q: essure in gravity dams: A drainage gallery reduces the uplift pressure at all levels below the…

Q: A filter is designed with the following specifications. The anthracite and sand have densities of…

A: A filter is designed with the following specifications. The anthracite and sand have densities of…

Q: A 8 m 3 m B 3m- 6 m 1.5 m 1 m

Q: compute for moment of inertia along x - axis (lx), and the moment of inertia along y-axis (ly) 10 mm…

Q: essure in gravity dams: A drainage gallery reduces the uplift pressure at all levels below the…

Q: Consider the following statements related to uplift pressure in gravity dams: 1. A drainage gallery…

Q: external and internal reactions of the structural

Q: Is there any solution manual for this book? Mechanics of Materials Volume 1, Third Edition An…

A: Is there any solution manual for this book? Mechanics of Materials Volume 1, Third Edition An…

Q: A 250-k column load is to be supported on a 9 ft square footing embedded 2 ft below the ground…

A: Load = 250 kWidth (B) = 9 ft Depth = 2 ft N60 = 32

Q: What is the value of the shear stress at the neutral axis in a rectangular section of base b, height…

Q: Consider the following statements related to uplift pressure in gravity dams: 1. A drainage gallery…

Q: A centrifugal pump having outer diameter equal to two times the inner diameter and running at 1000…

A: Running speed = 1000 rpmTotal head = 40 mVelocity of flow = 2.5 m/sVane angle = 40 degreeDiameter of…

Q: (Q3) In a vertical parabolic curve (g1=+1.0% and g2=-1.6%) compute: Station of the PVC if you know…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 10 KN A 15 KN 450 4 m 30 KN B

Q: The beam, W410 mm x 67 kg/m, with 9mm web thickness subjects the girder, W530 mm x 109 kg/m with 12…

A: Bolt shear stress, Fv = 120 MPaBolt bearing stress, Fp = 480 MPaweb thickness, t = 9 mmTo find:The…

Q: The bottom width, side slopes and Manning's n and bed slope of a trapezoidal channel are…

A: Bed width (b) = 40 m Manning's roughness coefficient (n) = 0.015Discharge(Q) = 60 m3/s Side slope (m…

Q: 6.24. In Problem 6.6, what is the maximum downwind distance at which the ground level con-…

A: Wind speed (V)= 3 m/s Stability class CEmisson rate (Q) = 1000 g/s Ground level concentration (C)=…

Q: Load factor for a single flight can be determined by dividing the number of passengers by the number…

A: Load factor for a single flight can be determined by dividing the number of passengers by the number…

Q: The axis shown in the figure is supported by a thrust bearing in A and a pillow block in B. Draw the…

A: Compute the support reactions:Using the equilibrium condition:

Q: oh of each phase in a two-phase specimen, how does phase boundary area vary with the shape of the…

A: Physical property differences between the two scenarios will vary depending on the material, the…

Q: List the properties of flow net with figure.

A: Given data in question Flow netTo find out Properties of flow net

Q: a) Draw a free-body diagram and solve for all reaction forces. b) Solve for the deflection of point…

Q: 5. Consider the system given below. The diameter of the orifice at the bottom is 5 cm. Determine the…

A: do = 5 cm or 0.05 m Q1 = 10 L/s h = 50 cm or 0.5 m

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

I need a clear answer by hand, not
by keyboard and fast answer within
20 minutes. Thank you | dybala
For the beam loaded as
shown, find the maximum tensile
and compressive bending stresses
and maximum shearing stress..
IN.A=4*10mm*
80mm
100mm
60mm
60mm
1.5KN
2kN/m
1mal
A
|-----|- |
Im
++
Im->>
3m
3kN/m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given question

VIEW

Step 2: Shea force diagram

VIEW

Step 3: Bending moment diagram

VIEW

Step 4: Maximum tensile stress calculation

VIEW

Step 5: Maximum compressive stress & shear stress

VIEW

Solution

VIEW

Step by step

Solved in 6 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For the frame shown, a 4QQT-N load is acting on member ABD at D. If the allowable material shear stress for is 4Q MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
4. The plate shown in the figure is fastened to thefixed member by seven 10-mm-diameter rivets.Compute the value of the loads P so that theaverage shearing stress in any rivet does notexceed 70 MPa.
Prob 01: An 18” depth beam is bolted to a 24” depth girder is connected similar to that in figure shown below. Thediameter of the rivet is 20mm and the angles are each 100mm x 100mm x 12mm thick. For each bolt, assume thatthe allowable bearing stress is 220 MPa. Determine the allowable load P in KN on the connection. *show all theload P in kN for bearing stressBeam web thickness = 5mmGirder web thickness =
What is the minimum required bolt diameter (mm) at C ifthe allowable bolt shear stress is 68 Mpa.a. 9 mm c. 11 mmb. 10 mm d. 12 mm Determine the stress (Mpa) in strut BC.a. 5.6 MPa c. 3.2 MPab. 2.8 MPa d. 6.4 MPa Calculate the bolt stress (Mpa) at A if its diameter is 20mm.a. 7.64 MPa c.11.46 MPab. 3.82 MPa d.14.92 MPa
The one end of a hollow square bar whose side is 10 with 1 thickness is under a tensile stress 102500 and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σall =243000 psi for pin material.
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
STRENGTH OF MATERIAL(SIMPLE STRESS) PLEASE INCLUDE FBD 100% GUARANTEE UPVOTE
A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN at D (see figure). Let the dimension variablebe b = 240 mm.(a) Find the minimum permissible diameter dminof the bracket if the allowable normal stress is110 MPa.(b) Repeat part (a), including the weight ofthe bracket. The weight density of steel is77.0 kN/m3.
A square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. Use a501 plate and a502 gr2 rivet a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
Provide FBD Show clear hand writing and complete solution. Thank you The thrust bearing supports a load P = 275kN. Finda. The tensile stress in the rodb. The shearing stress between the thrust bearing and the rodc. The bearing stress between the thrust bearing and the support.