Identify what is the system in this problem and write the general energy balance equation (no need to solve) A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the specific delta H?

Identify what is the system in this problem and write the general energy balance equation (no need to solve) A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the specific delta H?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.19P

See similar textbooks

Similar questions

A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
Steam flows through a turbine at the rate of 100 lb/min with ∆KE = 0 and Q = 0. At entry, its pressure is 175 psia, its volume is 3.16 ft3/lb, and its internal energy is 1166.7 Btu/lb. At exit, its pressure is 0.813 psia, its volume is 328 ft3/lb, and its internal energy is 854.6 Btu/lb. What horsepower is developed? (b) The same as (a) except that the heat loss from the turbine is 10 Btu/lb of steam.
Steam enters a turbine with an enthalpy of 1292 BTU/lb and leaves with an enthalpy of 1098 BTU/lb. The heat loss is 13 BTU/lb. What is the work done per BTU/min and in hp for a flow of 2 lb/sec? Provide complete solution, with diagram
At the inlet of a steady-flow steam turbine, the water vapor velocity is 55 m / s, the temperature is 600 ° C and pressure is 4 MPa, at its out; speed is 190 m /s,pressure is 15 kPa and its dryness is 92 percent. Meanwhile, heat transfer of 1800 kj / minute from the environment to the turbine is realized. Water Steam turbine power is 5 MW. Neglecting the potential energy change; a)Find the mass flow of water vapor. b)Find the inlet cross section of the turbine.
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
Water flowing at 0.5 m3/min enters the turbine of a micro-hydroelectric generator and delivers a shaft work of W= 2,500 J/kg. What is the power delivered by the generator if it works at 95% efficiency, n = 0.95?
Water is fed to an inward flow reaction turbine, running at 180 rpm with a velocity of flow of 3 m/s. The diameter and width of the wheel at inlet are 1 m and 135 mm, respectively. Assuming the velocity of flow to be constant and radial discharge at inlet and outlet, find, (a) work done per kN of water, (b) power developed by the turbine, (c) head of water on the turbine, and (d) hydraulic efficiency of the turbine. Also, draw velocity triangles showing all details.
At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg. (i) Drum Dia and blade height if heigh is one-twelfth of the drum dia. and the steam flow is 120 kg/sec. (ii) The percentage increase in the relative velocity across the bladings as a result of pressure drop across the blading.
Pls. Answer this thank you!Steam enters a turbine stage with an enthalpy of 3628 kj/kg at 70 m/s and leaves the same stage with an enthalpy of 2846 kj/kg and a velocity of 124 m/s. Calculate the power in KW if there are 5 kg/s steam admitted at the turbine throttle.
A turbine is discharging 10m3/s under a head of 22 m at 200 rpm. The efficiency is 90%. Determine the performance of turbine under a head of 44 m.
Air enters a fan through a duct at a velocity of 6.3 m/s and an inlet static pressure of 2.5 cm of water less than atmospheric pressure. The air leaves the fan through a duct at a velocity of 11.25 m/s and a discharge static pressure of 7.62 cm of water above the atmospheric pressure. If the specific weight of the air is 1.2 kg/m3 and the fan delivers 9.45 m3/s, what is the fan efficiency when the power input is 13.75 kW at the coupling?