a) Calculate F when W=120 lb and θ=30°?b) Use an identity to show that F is approximately equal to W cos θc) For what value of θ is F maximum? If a person bends at the waist with a straight back making an angle of 0 degrees with the horizontal, then the force F exerted on the back muscles can be modeled by the equation shown below,where W is the weight of the person. Complete parts (a) through (c).0.6W sin (0 +90°)F=sin 12°

Step 1: Step 2: Step 3: Step 4:

Answered: If a person bends at the waist with a…

Trigonometry (MindTap Course List)

10th Edition

ISBN:9781337278461

Author:Ron Larson

Publisher:Ron Larson

Chapter2: Analytic Trigonometry

Section2.1: Using Fundamental Identities

Problem 67E

See similar textbooks

Similar questions

Gear Trains Figure 8 shows a single-stage gear train. Gear trains are used in many products, such as clocks and automotive transmissions, to reduce or increase the angular velocity of a component. The size of each gear is measured by the number of teeth rather than the radius. Suppose the first gear has n1 and the second gear has n2 teeth. Because the spacing of the teeth is the same for both gears, the ratio of their radii will be equivalent to the corresponding ratio of the number of teeth. When two gears are meshed together, they share the same linear velocity. If 1 and 2 are the angular velocities of the first and second gears, respectively, then v2=v1r22=r112=r1r212=n1n21 The first gear in a single-stage gear train has 42 teeth and an angular velocity of 2 revolutions per second. The second gear has 7 teeth. Find the angular velocity of the second gear.
Gear Trains Figure 8 shows a single-stage gear train. Gear trains are used in many products, such as clocks and automotive transmissions, to reduce or increase the angular velocity of a component. The size of each gear is measured by the number of teeth rather than the radius. Suppose the first gear has n1 and the second gear has n2 teeth. Because the spacing of the teeth is the same for both gears, the ratio of their radii will be equivalent to the corresponding ratio of the number of teeth. When two gears are meshed together, they share the same linear velocity. If 1 and 2 are the angular velocities of the first and second gears, respectively, then v2=v1r22=r112=r1r212=n1n21 The second gear in a single-stage gear train has 6 teeth and an angular velocity of 90 revolutions per minute. The first gear has 54 teeth. Find the angular velocity of the first gear.

Recommended textbooks for you

Trigonometry (MindTap Course List)

Trigonometry

ISBN:

9781337278461

Author:

Ron Larson

Publisher:

Cengage Learning

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Trigonometry (MindTap Course List)

Trigonometry

ISBN:

9781305652224

Author:

Charles P. McKeague, Mark D. Turner

Publisher:

Cengage Learning

Trigonometry (MindTap Course List)

Trigonometry

ISBN:

9781337278461

Author:

Ron Larson

Publisher:

Cengage Learning

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Trigonometry (MindTap Course List)

Trigonometry

ISBN:

9781305652224

Author:

Charles P. McKeague, Mark D. Turner

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

If a person bends at the waist with a straight back making an angle of 0 degrees with the horizontal, then the force F exerted on the back muscles can be modeled by the equation shown below, where W is the weight of the person. Complete parts (a) through (c). 0.6W sin (0 +90°) F= sin 12°