If an isotropic material has a shear modulus of 125 Gpa and a Poisson's ratio of 0.2, calculate its Young's modulus.
Q: If an isotropic material has a Young's modulus of 200 Gpa and a Poisson's ratio of 0.3, calculate…
A:
Q: What is the ratio of shear modulus to the modulus of Elasticity if Poission's ratio is 0.25
A: Given:Poission's ratio, ϑ=0.25
Q: A plastic bar of 88 mm is to be twisted by torques T until the angle of rotation between the ends of…
A:
Q: If the Poisson's ratio of an elastic material is 0.4, the ratio of modulus of rigidity to Young's…
A:
Q: Calculate the elastic strain in a polycrystalline aluminum alloy when it is pulled in tension given…
A: This question is based on the concept of solid mechanics.
Q: Explain the differences between a ductile material and brittle material. Also, draw their…
A: DUCTILE MATERIALS: 1. Ductile material are those which undergoes large plastic deformation under the…
Q: If an isotropic material has a shear modulus of 11 Gpa and a Poisson's ratio of 0.34, calculate its…
A:
Q: 13. For a given material, Young's modulus is 110 GN/m² and shear modulus is 42 GN/m2. Find the bulk…
A:
Q: A torque of 3300 N-m is transmitted through a 50 mm diameter shaft having a yield stress in shear of…
A:
Q: A material has an appreciable elongation without any increase in load is
A: Answer: B. Yielding A material has an appreciable elongation without any increase in load is called…
Q: Identify the material that has a maximum modulus of elasticity from the following stress-strain…
A: Material A has higher modules of elasticity.
Q: Explain ELASTIC STRAIN ENERGY FOR VARIOUS TYPES OF LOADING?
A: The energy stored in a body up to elastic limit under certain loading is called the elastic strain…
Q: Calculate the modulus of elasticity of the following material if it has a design stress of 250 kPa,…
A:
Q: If for a given material, E = 2G (E is modulus of elasticity, G is the shear modulus), then the bulk…
A: from the relationship between the elastic constants we know E = 2G( 1+μ)E = 3k( 1-2μ)μ = poisson's…
Q: If the shear stress in a material is 20 MPa and the corresponding shear strain is 0.0005, calculate…
A:
Q: Sketch a graph of Hooke’s Law and label the elastic region, plastic region, yield tensile strength…
A: Hooke's law- According to the law the stress induced in the material is directly proportional to the…
Q: 4: A machine with a mass of "300" tons was placed on 6 legs. Feet are square section; its dimensions…
A:
Q: An Aluminum plate of thickness 5 mm has ultimate strength of 70 GPa. The shear force required by the…
A: Given, Thickness of plate = t = 5 mm Ultimate strength of material = τu = 70 GPa = 70,000 MPa…
Q: Sketch a load-displacement plot for a linear elastic material, then illustrate on the plot how V…
A: Linear elastic material - Materials that obey Hooke's law are known as linear elastic materials.
Q: Evaluate bulk modulus, if modulus of rigidity and Poisson’s ratio for a material are 75 GPa and 0.3…
A: Modulus of rigidity, G=75GPa Poisson's ratio, μ=0.3
Q: If the moduli of rigidity and elasticity of a material are 15,000 ksi and 40,000 ksi, respectively,…
A:
Q: If an isotropic material has a Young's modulus of 120 Gpa and a Poisson's ratio of 0.3, calculate…
A:
Q: Stress-Strain behavior of a hypothetical material is given below. Using 0.2 % offset yield strength…
A:
Q: For a given material, the Young's modulus is 2.8 times that of rigidity modulus. The Poisson's ratio…
A: When an amount of load act on the object it has the tendency to change the shape of the object, so…
Q: A cylindrical specimen of a nickel alloy having an elastic modulus of 207 GPa and an original…
A:
Q: Pls answer thank you ! The modulus of elasticity of a material is 207 GPa and the modulus of…
A:
Q: A force of 25,000 N will cause 1cm x 1cm bar of carbon steel to stretch from 20 cm to 20.040 cm.…
A:
Q: 3. Derive an equation relating the elastic modulus of a unidirectional composite, a load applied in…
A: Actual cross-section of the composite is shown below in figure (i). But to find the transverse…
Q: For a material, Young's modulus is given as 3.2 X 105 N/mm2 and Poisson's ratio is (1/4) Calculate…
A: Given data : Youngs modulus=EPoisson's ratio =μTo find :Bulk modulus
Q: A cylindrical sample that is produced from a metal is tested under compression. The metal has a…
A: Given data: The Young's modulus of the metal is E = 150 GPa. The shear modulus of the metal is G =…
Q: Calculate the Vickers hardness when a 700-g load yields an indentation diagonal length of 0.050 mm.
A: Given data: P=700 gd=0.05 mm Need to determine the Vickers hardness.
Q: 4. Why is modulus a characteristic property but not yield strength.
A: The Young modulus, also known as the modulus of elasticity in tension or compression (i.e., negative…
Q: A structural material has a modulus of elasticity of 8 x 10^6 psi and a modulus of rigidity of 3.2 x…
A: Given data: Modulus of elasticity of the material, E = 8×106 psi. Modulus of rigidity of the…
Q: 2. Consider a cylindrical nickel wire 0.08 in. in diameter and 1200 in. long. Calculate its…
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: Draw a load vs. displacement curve as obtained from a homogeneous material using nanoindentation.…
A: Load vs Displacement curve-
Q: A cylindrical specimen of a metal alloy 10 mm in diameter is stressed elastically in tension. A…
A: Since you have asked multiple questions in a single request we would be answering only the first…
Q: Draw a hypothetical stress-strain curve and mention the yield stress, ultimate tensile strength,…
A:
Q: If the Poisson's ratio of an elastic material is 0.8 the ratio of modulus of rigidity to Young's…
A: This question is based on the concept of elastic properties of material. Poisson's ratio= 0.8
Q: If elastic modulus of material is 200 GPa and Poisson's ratio is 0.29, Bulk modulus is:
A: Given data, E= 200 GPa, Poisson's ratio μ=0.29 Need to find bulk modulus K
Q: A metal wire of diameter 1.2 mm is used to carry a load of 1100 N. If the material of which the wire…
A:
Q: Sketch two more stress-strain diagrams, again one for a ductile material and one for a brittle…
A: Stress and strain: Stress is defined as the internal resisting force per unit area; it represents…
Q: Calculate the stress of the cylindrical rod. Compare with data given in Table Q1 which are the…
A: we have to calculate the stress
Q: For a given material. Young's Modulus is 200 GN/m? and Modulus of Rigidity is 80 GN/m?. Its Poisson…
A: Given, Young's modulus = E = 200 GPa Modulus of rigidity = G = 80 GPa From the relation between…
Q: Consider a cylindrical titanium wire with crossectional area of 7 mm^2 and 2.5 x 104 mm long.…
A: Write the expression for elongation in the rod.
Q: If an isotropic material has a shear modulus of 125 Gpa and a Poisson's ratio of 0.2, calculate its…
A:
Q: round bar of 25mm in diameter undergoes a tensile load of 120kpa. The gage length is 30cm and…
A:
Q: Write down the Uniaxial, Bending and Torsional loading rigidity terms, and specify the name of…
A:
Q: If the Poisson's ratio of an elastic material is 0.6 the ratio of modulus of rigidity to Young's…
A:
Q: Q: Consider a cylindrical titanium wire 3.0 mm in diameter and 2.5 x 104 mm long*. Calculate its…
A:
Step by step
Solved in 2 steps with 2 images
- A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?A spherical steel pressure vessel (diameter 500 mm, thickness 10 mm) is coated with brittle lacquer that cracks when the strain reaches 150 X 10~ (see figure). (a) What internal pressure p will cause the lacquer to develop cracks? (Assume E = 205 GPa and v = 0.30.) (b) If the strain is measured at 125 x 10-6, what is the internal pressure at that point?Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
- Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
- A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
- Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.