I need the answer as soon as possible If modulus of elasticity of a material is189.8 GN/m2 and its Poisson's ratio is 0.30, whatis the approximate value of shear modulus of thematerial?(a) 73 GN/m2(C) 103.9 GN/m2(b) 93.3 GN/m2(d) 123.3 GN/m2

Given data : Poisson' ratio (μ)=0.3Modulus of elasticity (E)=189.8 GN/m2

Answered: If modulus of elasticity of a material…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB? Determine the average shear strain in the plate at A relative to the horizontal and vertical axes? In micro rad
Calculate the value of rate of deformation in yz direction
50% Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 32 in., b= 40 in., δ1= 0.225 in., δ2= 0.075 in. Determine the average normal strain along the side AB? Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
A flat bar with a cross section of 8 mm by 50 mm elongates 2.1 mm in a length of 1.5 m as a result of an axial load of 50 kN. The proportional limit of the material is 240000 KN/sq m. Determine the axial stress in the bar and the modulus of elasticity
A plate 0.035mm distant from a fixed plate, moves at 80 cm/s and shear stress is 2 N/m2 to maintain this speed. Determine the fluid viscosity between the plates.
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 17 MPa, Sy = 29 MPa, and Sxy = 26 MPa. Assume β=tan^−1(b/a)=23.2∘, a = 7, and b = 3. Using the equilibrium equation approach, determine the normal and shear stresses σ (positive if tensile, negative if compressive) and ττ (magnitude only) at this point on the inclined plane shown.
The extruded plastic shape has dimensions of D = 21 mm. d = 17 mm. a = 87 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 360 N. (b) If the allowable shear stress for the plastic material is 1050 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
The extruded plastic shape has dimensions of D = 23 mm, d = 21 mm, a = 93 mm, and t = 3 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 360 N.(b) If the allowable shear stress for the plastic material is 2250 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 24.3 ksi, Sy = 2.7 ksi, and Sxy = 4.1 ksi. Assume β=25∘β=25∘. Determine the normal stresses σxσx and σyσy and the shear stress τxyτx⁢y at the point.
A steel rod with a diameter of 12 mm, on which two points were fixed, with a distance of 75 mm between them, and then a pulling force of 10.5 kilonewtons was applied to it, so the distance between the two points increased by 0.035 mm and the diameter decreased by 0.0015 mm. What is the stress generated in the steel bar in megapascals? What is the type of stress generated? What is the amount of longitudinal strain? What is the amount of transverse strain? What is the modulus of elasticity for the steel rod?
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 28 MPa, Sy = 28 MPa, and Sxy = 37 MPa. Assume β=tan−1(ba)=21.8∘β=tan-1(ba)=21.8∘, a = 5, and b = 2. Using the equilibrium equation approach, determine the normal and shear stresses σσ (positive if tensile, negative if compressive) and ττ (magnitude only) at this point on the inclined plane shown.
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 22 ksi, Sy = 1.5 ksi, and Sxy = 5.2 ksi. Assume β=21∘. Determine the normal stresses σx and σy and the shear stress τxy at the point.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

If modulus of elasticity of a material is 189.8 GN/m2 and its Poisson's ratio is 0.30, what is the approximate value of shear modulus of the material? (a) 73 GN/m2 (C). 103.9 GN/m2 (b) 93.3 GN/m2 (d) 123.3 GN/m2