If P = 35 kN, determine the total strain energy stored in the truss. Each member has a cross-sectional area of 3500 mm2 and is made of 2014-T6 aluminum (E=75 GPa). - 2 m 1.5 m A Lütfen birini seçin: a. 51.5 J O b. 54.3 J c. None d. 42.4 J e. 59.4 J

If P = 35 kN, determine the total strain energy stored in the truss. Each member has a cross-sectional area of 3500 mm2 and is made of 2014-T6 aluminum (E=75 GPa). - 2 m 1.5 m A Lütfen birini seçin: a. 51.5 J O b. 54.3 J c. None d. 42.4 J e. 59.4 J

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.4P: An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy =...

See similar textbooks

Related questions

Q: 6. Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L…

A: Given:P=8 KNL=400 mmν=0.35E=70 GPa

Q: 10-11. The state of strain on an element has components q = -150(10-9), e, = 450(10-9). Yay =…

Q: The polysulfone block is glued at its top and bottom to the rigid plates. If a tangential force,…

A: GIVEN :-y=3.56x14TO DETERMINE :-the shear strain at the corners A and B,

Q: The steel shaft has a radius of 15 mm. Determine the torque T in the shaft if the two strain gages,…

A: Write the given data:

Q: The rigid beam ABC is supported by pin A and wires BD and CE. If the load P on the beam causes the…

Q: The load P produces an axial strain of –1,800 µɛ in post (2). Determine the axial strain in rod (1).…

Q: Acetal plastic has a stress-strain diagram as shown. If a bar of this material has a length of 3 ft…

Q: The normal stresses at a point in a steel member are σx = 8 ksi, σy = -4 ksi, and σz = 10 ksi. Using…

Q: Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L =…

Q: Determine the Poisson's ratio if the lateral strain is -0.1 and longitudinal strain is 0.4 Select…

A: Given data : Longitudinal strain is denoted by εL Lateral strain is denoted by εLt To find :…

Q: Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L =…

A: Given:-P=8 kNL=400 mmE=70 GPa=70×109 Pav=0.35To find:-Lateral strain

Q: If the normal strain is defined in reference to the final length Δs′, that is,P= = lim Δs′S 0 aΔs′ -…

A: Given ε'=lim∆s→0∆s'-∆s∆s'

Q: if the rod is subjected to a tensile load P = 6 kN, and has a diameter of 44 mm. if the modulus of…

Q: Determine the Poisson's ratio if the lateral strain is -0.1 and longitudinal strain is 0.4 Select…

A: As per given question we have determine poisson's ratio

Q: 11.4 (A/B). Compare the strain energies of two bars of the same material and length and carrying the…

Q: What strain will be produced by a stress of 20 x 10° N/m?, for a given modulus of elasticity 100GPA.…

A: Stress = 20 × 10 6 N/m2 modulus of elasticity = 100 Gpa =100×109N/m² Stress = Strain × modulus of…

Q: A strain gage is mounted to the outer surface of a thin-walled boiler. The boiler has an inside…

Q: Determine the maximum force P and the corre- sponding maximum total strain energy that can be stored…

Q: The 45° strain rosette is mounted on the surface of a shell. The following readings are obtained for…

A: Given that,εa=-200×10-6εb=300×10-6εc=250×10-6Here,εx=εc=250×10-6εy=εa=-200×10-6

Q: The state of plane strain at a point has strain components of Px = -400(10-6), P y = 200(10-6), and…

A: The components of strains are given as, εx=-400×10-6εy=200×10-6γxy=150×10-6 The principal…

Q: b) Define volumetric strain. Prove that the volumetric strain fora rectangular bar subjected to an…

Q: A= 1200 mm?. Use Strain Energy Method 35 kN - 4m B 84 kN 4m 3m

Q: H.W.2: The load P produces an axial strain of -1,800 ue in post (2). Determine the axial strain in…

Q: If a load of P = 3 kip is applied to the A-36 structural-steel beam, determine the strain P x and…

A: Calculate the moment at point A due to the force P. M=Px Here, x is the distance between point A and…

Q: The rigid bar is pinned at A and supported by two aluminum rods, each having a diameter of 1 in. a…

A: P=20 Kips =88.964432 kN L1=distance between the point A to C =0.3048 m ; L2=distance between the…

Q: A 20-mm diameter steel rod, 250 mm long is subjected to a tensile force of 75 kN. If the Poisson’s…

Q: The 45° strain rosette is mounted on a steel shaft. The following readings are obtained from each…

Q: 10. The 8-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has…

Q: A string 4 mm in diameter has original length 2 m. The string is pulled by a force of 200 N. If the…

Q: The 60o strain rosette is mounted on a beam. The following readings are obtained for each gage: ϵa =…

A: Write the given data:

Q: 10–11. The state of strain on an element has components €x = -150(10-6), €, = 450(10-"), Yxy =…

Q: The strain at point A on the bracket has normal components 750x106 and 150x106 in x and y…

Q: 3. Each member of the truss is made of steel and has the cross-sectional area shown. Determine the…

A: Given Data: Young's Modulus E=200 Gpa=200×103Nmm2 Area of Trusses ACD=ACB=1500 mm2 and ABD=2000 mm2…

Q: 01-Determine the new length of Bar have two parts. The first with diameters3 in, length is12 ft. and…

Q: The strain in the a direction at point A on the A-36 structural-steel beam is measured and found to…

Q: Determine the total strain energy in the steel assembly. Consider the axial strain energy in the two…

A: From the above given FBDThe load is located at the middle of the beamso both the supporting…

Q: The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a…

Q: Determine the Poisson's ratio if the lateral strain is -0.1 and longitudinal strain is 0.4 Select…

A: Given data : The value of lateral strain is=-0.1 The value of longitudinal strain=0.4 To find :…

Q: The strain components ex = 466 µE, ey = -524 µe, and yxy = -646 µrad are given for a point in a body…

Q: at A has coordinates (0, 0). If a load P acts on the ring at 3 becomes EAB = 0.02 in/in., and the…

A: data providedthe length of rod AB LAB = 5 in the length of rod Ac ,LAC = 8 in The normal…

Q: Determine the maximum force P and thecorresponding maximum total strain energy stored in thetruss…

A: The given area of cross-section of each member is The required properties of the A-36 steel are:

Q: The timber member has a cross-sectional area of 1850 mm² and its modulus of elasticity is 12 GPa.…

Q: Determine the Poisson's ratio if the lateral strain is -0.1 and longitudinal strain is 0.4 Select…

Q: The 45° strain rosette is mounted on a steel shaft. The following readings are obtained from each…

A: Given data: Strain rosette of 45° angle is attached to the steel shaft εa…

Q: If P = 35 kN, determine the total strain energy stored in the truss. Each member has a…

Q: 11.3 (A) Calculate the strain energy stored in a bar of circular cross-section, diameter 0.2 m,…

Q: The bar has a length of 8 in. and a square cross-sectional area of 0.5 in. × 0.5 in. It is made of a…

Question

please

If P = 35 kN, determine the total strain energy stored in the
truss. Each member has a cross-sectional area of 3500 mm2
and is made of 2014-T6 aluminum (E=75 GPa).
- 2 m
B
1.5 m
A
VP
Lütfen birini seçin:
a. 51.5 J
b. 54.3 J
c. None
d. 42.4 J
e. 59.4 J

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the strain if a rod is experiencing a stress of 70,000kPa with a modulus of elasticity of 175 GPa.a. 300 x 10−6b. 400 x 10−6c. 500 x 10−6d.. 600 x 10−6
A 20-mm diameter steel rod, 250 mm long is subjected to a tensile force of 75 kN. If the Poisson’s ratio μ is 0.30, determine the lateral strain of the rod. Use E = 200 GPa. Ans; Ey= -3.581x10^-4mm/mm
The 45° strain rosette is mounted on the surface of a shell. The following readings are obtained for each gage: Pa = -200(10-6), Pb = 300(10-6), and Pc = 250(10-6). Determine the in-plane principal strains.
The steel shaft has a radius of 15 mm. Determine the torque T in the shaft if the two strain gages, attached to the surface of the shaft, report strains of Px = -80(10-6) and Py = 80(10-6). Also, determine the strains acting in thex and y directions. Est = 200 GPa, nst = 0.3.
A single strain gage, placed in the vertical plane on the outer surface and at an angle 60° to the axis of the pipe, gives a reading at point A of PA = -250(10-6). Determine the principal strains in the pipe at this point. The pipe has an outer diameter of 1 in. and an inner diameter of 0.6 in. and is made of C86100 bronze.
The state of plane strain at a point has strain components of Px = -400(10-6), P y = 200(10-6), and gxy = 150(10-6), Fig. a. Determine the maximum in-plane shear strain and the absolute maximum shear strain.
Determine the maximum force P and thecorresponding maximum total strain energy stored in thetruss without causing any of the members to have permanentdeformation. Each member has the cross-sectional area of2.5(103) mm2 and is made of A-36 steel.
If the normal strain is defined in reference to the final length Δs′, that is,P= = lim Δs′S 0 aΔs′ - Δs Δs′ b instead of in reference to the original length, Eq. 2–2, show that the difference in these strains is represented as a second-order term, namely, P - P= = P P′.
The 45° strain rosette is mounted on the surface of a pressure vessel. The following readings are obtained for each gage: Pa = 475(10-6), Pb = 250(10-6), and Pc = -360(10-6). Determine the in-plane principal strains
Determine the shear strain ??? at the corners C and D if theplate distorts shown by the dashed lines. (2) Determine theaverage normal strain that occurs along the diagonals AC andBD.
6. A prismatic bar of length L is subjected to axial load P. Determine the maximum strain & along the bar length, given that the axial displacement along the member length varies according u = (12/L) × 10-3.
The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Determine the average normal strain Px along the x axis.