If the beam in the figure below is in equilibrium (A is a pin and B is a roller), determine the following: (Neglect the thickness of the beam) 450 N 300 N 30 A m 4 m A. Replace the supports on points A and B with their reaction forces. B. Draw the FBD for the beam. C. Write the equilibrium equations of the forces in x, y axes. D. Write the equilibrium equation of the moment around point A. E. Determine the reaction forces acts on A and B.

If the beam in the figure below is in equilibrium (A is a pin and B is a roller), determine the following: (Neglect the thickness of the beam) 450 N 300 N 30 A m 4 m A. Replace the supports on points A and B with their reaction forces. B. Draw the FBD for the beam. C. Write the equilibrium equations of the forces in x, y axes. D. Write the equilibrium equation of the moment around point A. E. Determine the reaction forces acts on A and B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the moment of force F in the figure about the AC axis
Determine the moment over the support A and B of the beam shown in the figure using Three-Moment equation.
Solve for the moment of the 50N force about point O in the figure given.
The coefficient of static friction between the drum and brake bar is μs = 0.4. If the moment M = 35 N ⋅ m, determine the smallest force P that needs to be applied to the brake bar in order to prevent the drum from rotating.Also determine the corresponding horizontal and vertical components of reaction at pin O. Neglect the weight and thickness of the brake bar. The drum has a mass of 25 kg.
Calculate the equivalent force of the distributed load and the Support Reactions (Ax, Ay and By).
Learning Goal: To determine the reaction forces at supports on a horizontal beam by using the equations of equilibrium for a static application. As shown, beam ABC is supported by the roller at A and pin at C. The geometry of the beam is given by a=2.0a=2.0 ftft, b=6.0b=6.0 ftft, and c=11.0c=11.0 ftft. The applied forces are F1=1.50F1=1.50 kipkip and F2=2.00F2=2.00 kipkip. Force F1F1 is applied at an angle θ=35∘θ=35∘ with the horizontal. Neglect the weight of the beam. Determine the vertical reaction at A. Determine the horizontal component of the pin reaction at C. Determine the vertical component of the pin reaction at C.
A Pole is connected to the wall with a ball and socket joint and also supported by two cables. The weight of the pole is 80 lb. Forces F1 and F2 are applied to the pole at point D. F1 is + 120j lbs. and F2 is -340k llbs. (a) Draw the free body diagram of the pole, make a list of all of the coordinates for each point, and write your assumptions.(b) Write the full set of equilibrium equations for the pole.(c) solve for the tension in the cable CG and DF and for the reaction forces at A. The two cables are separate.Augmented Matrix for RREF. When you copy your Augmented Matrix into MatLab, remember to only use the same number of equations (rows) as you have unknown values.
Calculate the reaction force at joint H and joint A.
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the maximum positive moment in the beam in kN.m.0
A barge floating in water, is loaded as shown. Determine the length so that it will remain in horizontal position and will be subjected to a uniform upward buoyant pressure. Find the value of x and w. Draw the shear and moment diagram.
Determine the moment of the two forces about X, Y and Z axes shown in the figure
Calculate for the beam shown below the components Ax and Ay of the reaction force in the setting (point A) and the moment MA present in the same setting, in such that the beam is in balance.