please solve this example in short way If V GSQ = 7 V in the circuit in the figure, C1 = 57 nF and C2 = 41 nF, what is the low cutoff frequency of the system?NOTE: rd will be taken into account in the calculations.+20 V10 kQC222 M2C1VesCT = 3.5 Vk= 0.3 x 10-3Lor = 30 usO a. 151.44HZO b. 353.35 HzO c. 100.96HZO D. 504.79HZO to. 50.48HZO f. 302.87HZO g. 252.39HZO h. 403.83 Hz

Answered: If V GSQ = 7 V in the circuit in the…

If V GSQ = 7 V in the circuit in the figure, C1 = 57 nF and C 2 = 41 nF, what is the low cutoff frequency of the system? NOTE: will be taken into account in the calculations. +20 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i just need final answer If VGSQ = 7 V, C1 = 21 nF and C2 = 110 nF in the circuit in the figure, what is the low cut-off frequency of the system? NOTE: rd will be taken into account in calculations. a.37,63 Hz b.18,81 Hz c.112,89 Hz d.188,15 Hz e.150,52 Hz f.131,70 Hz g.56,44 Hz h.94,07 Hz
The parameters in the circuit shown in Figure-4 are Vp 0.7 V, Vi=2.3 V, and Vzz = 5.6 V. Find and plot Vo versus Vi over the range of -10 Vi+10 V (Hint: You can consider input signal as sine wave of amplitude of +10 V and -10 V). Note: please solve within 30 minutes. Avoid plagiarism.
ı just need fınal aswer If VGSQ = 7 V, C1 = 32 nF and C2 = 150 nF in the circuit in the figure, what is the low cut-off frequency of the system? NOTE: rd will be taken into account in calculations. a. 68,99 Hz b. 110,38 Hz c. 13,80 Hz d. 27,60 Hz e. 41,39 Hz f. 82,79 Hz g. 96,58 Hz h. 137,98 Hz
Electronic If VGSQ = 7 V, C1 = 11 nF and C2 = 105 nF in the circuit in the figure, what is the lower cutoff frequency of the system?
The figure below shows a phase shift oscillator with amplitude control. Design the circuit to produce 7kHz frequency and a ±8V output waveform. Assume that I1 = 1mA and R2=R3. Do your design on a piece of paper and then enter the various resistor and capacitor. NOTE: Use only E24 values for your design Enter the values of R1=_____Ω, R2_____kΩ . , R3._____kΩ , R4._____kΩ . , R5_____kΩ , R6_____kΩ and R7 _____kΩ and the value of C=_____ μF
Answer the following with illustration and solutions. 2.) If C1 = C2 = 100pF, determine the output frequencies produced by this arrangement:a. (a) when R1 = R2 = 12kilo-ohms andb. (b) when R1 = R2 = 8kilo-ohms See the example below..
Propose a digital to analogue converter circuit using 1 op amp and 3 resistors (R1=200 kΩ, R2=100 kΩ, and Rf = 10 kΩ). The sequence of two binary codes is applied and represented by thewaveforms in Figure 3. A high level (2.5 V) is a binary 1 and low level (0 V) is a binary 0. Theleast significant digit is D0. Draw circuit diagram, show the calculation involved and sketch theoutput waveform.
When VGSQ=7V, C1=96nF C2=44nF What is the low cut-off frequency of the system? Note : rd will be taken into account in the calculations
Question 4. Design a C converter by drawing according to the values given below.The C ´uk converter has 24 V input and 36 V output providing 80 W load. In this case, choose Duty ratio, switching frequency, inductor dimensions so that the variation in inductor currents is not more than 5 percent of the average inductor current, output voltage fluctuation is less than 1 percent and voltage fluctuation at C1 is less than 5 percent.
Determine the output voltage, Vout when:R1 = 10000, R2 = 14110, Vref = 5V
1. If we add a Zero into a system: I. The gain slop will be increased by 20db/decade at its corner frequency. II. The gain slop will be decreased by 20db/decade at its corner frequency. III. Gain will not be affected. IV. None of the above. 2. If we add a Pole into a system: I. The phase will be increased by 90 degrees. II. The phase will decrease by 90 degrees. III. Phase will not be affected. IV. None of the above. 3. In systems, the Integrator add slop to the system gain equal to: I. 20 db/decade. II. -20 db/decade. III. 0 db/decade. IV. None of the above 4. The purpose of the Lag Compensator is: I. Improve the study state response of the close system. II. Speed up the transit response. III. All the above. IV. None of the above. 5. In the Lead Compensator: I. Z > P. II. Z < P. III. Z = P. IV. None of the above.
If VGSQ = 7 V and C1 = 34 nF and C2 = 77 nF in the circuit in the figure, what is the low cut-off frequency of the system? NOTE: rd will be taken into account in calculations.