pls only answer q ii Q1. Referring to the Figure Q1, answer the following questions:VAV;(ot)40 Vv(ot)20 VVm110 Ai(ot)Reference( 0°)3080°i) The maximum and effective (rms) values of v(wt), v;(wt) and i(wt). ii) Write the waveform equations of v(wt), v1(wt) and i(wt).

In the question II, Write the waveform equations of the given figure. Standard waveform equations…

Answered: ii) Write the waveform equations of…

Engineering

Electrical Engineering

ii) Write the waveform equations of v(wt), v;(wt) and i(wt).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a certain circuit supplied from 50 Hz mains, the potential difference has amaximum value of 500V and the current has a maximum value of 10A. At the instantt=0, the instantaneous values of the p.d. and the current are 400V and 4Arespectively, both increasing positively. Assuming sinusoidal variation, statetrigonometrical expressions for the instantaneous values of p.d. and the current attime t. Calculate the instantaneous values at the instant t=0.015s and find the angle ofphase difference between the p.d. and the current. Sketch the phasor diagram (neednot be to scale).
For the frequency-domain circuit , calculate: 1. a) the rms magnitude of Vo;2. b) the average power dissipated in the 9 Ω resistor;3. c) the percentage of the average power generated by the idealvoltage source that is delivered to the 9 Ω load resistor.
The feeder is to be used with an antenna for which an inductive reactance is measured as j60 Ohms at 1.7 MHz. The resistive part of the antenna’s impedance is measured as 80 Ohms. Using the online impedance matching calculator, design a suitable impedance-matching network for each of the two cables if the coaxial cable has a characteristic impedance of 75 Ohms and the twin lead cable has a characteristic impedance of 300 Ohms, so that the inductance is in the longitudinal branch, while the capacitor is in the transversal branch of the impedance matching network. Do not round the resulting values.
Please answer the following points in detail and rigorously. Instead ofresort to formulas, develop from basic principles (laws ofvoltages and currents, definition of electrical power, properties ofphasors, among others) a) Suppose that between the two terminals of an element there is a voltage v (t) and that through the terminal marked with a positive sign a current i (t). Show that if v (t) and i (t) are sinusoidal and are out of phase an angle θ, then the active power P which is consumed by this element is proportional to cosθ. b) How much is P for a pure inductor and how much for a capacitor pure? Does this make physical sense? c) When the power factor seen between two terminals is specified, Why is it necessary to indicate whether it is late or early? d) Show that the complex power consumed by two elements in parallel is the sum of the individual complex powers. After, repeat the procedure but for two elements in series. e) What meaning would you give to the P consumed by an…
An example power system has two distinct manufacturing areas, one with harmonic loads, and another with only linear loads. The portion of the system with the harmonic loads draws 75 A rms at 60 Hz, 10 A rms at 300 Hz, and 5 A rms at 420 Hz. The part of the system with only linear loads draws 75 A rms at 60 Hz. (i) What is the total load current (at 60 Hz) if both manufacturing plants are running? Calculate the THD. (ii) What is the total load current (at 60 Hz) if only the manufacturing plant with harmonic loads is running? Calculate the THD.
five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let R= 200, L=0.400H,C=6.0 Mf, and V=30.0 v. what's the reading of the voltmeter's V1,V2,V3,V4 and V5 if W= 200 rad/s
A voltage is given by v( t )=10 sin(1000πt+30°). First, use a cosine function to express v(t). Then, find the angular frequency, the frequency in hertz, the phase angle, the period, and the rms value. Find the power that this voltage delivers to a 50-Ω resistance. Find the first value of time after t=0 that v(t) reaches its peak value. Sketch v(t) to scale versus time. * Denotes that answers are contained in the Student Solutions files. See See Appendix E for more information about accessing the Student Solutions.
If the values of real power and reactive power is specified for a bus, then it is called as PQ bus. Select one: True False
Suppose the circuit shown represents a residential distribution circuit in which the impedances of the service conductors are negligible and Vg1=Vg2=120 0° V (rms). The three loads in the circuit are L1 (a new refrigerator, a coffee maker, and a microwave oven); L2 (2 incandescent lamps, a humidifier, and a ceiling fan); and L3 (a clothes washer and a clothes dryer). Assume that all of these appliances are in operation at the same time. The service conductors are protected with 20 A circuit breakers. Will the service to this residence beinterrupted? Why or why not?
Q6: An AC source operating at 60 Hz with a maximum voltage of 170 V is fed to a series combination of1.2kΩ resistor and 2.5μF capacitor connected in a timer circuit. How can you evaluate the maximumcurrent in the circuit? Can you estimate the rms value potential difference across each circuit element?Compare the power factor of this timer circuit with a circuit contain only ohmic resistance. Justify youranswer?
A. There is a sinusoidal current i(t) that has an rms value of 20 A, a period of 1 ms, and reaches a positive peak at t = .3 ms, write an expression for i(t). B. The voltage v(t) = 10 sin(250π(t)) V appears across a 20 ohm resistance. Sketch v(t) and p(t) to scale versus time. Find the average power delivered to the resistance.
Consider a PV module with the following external parameters at STC: Pmax = 320 W, VOC = 45 V, ISC = 8 A, NOCT =40 °C and the temperature coefficient of power is −1 W/°C. a) If the ambient temperature rises to 35 °C while the irradiance is 1,000 W/m2, what is the cell leveltemperature, calculated with the NOCT model?b) What is the new power output of the PV module under the new ambient temperature of 35 °C and 1,000W/m2irradiance?