Imagine having a plane wall of 5 in thickness and 6 ? area with two surfaces that are 2 maintained at 230°C and 70°C respectively. Determine the heat transfer between the surfaces and temperature gradient across the wall if conductivity of the wall material is16.5 W/(m-K).

Imagine having a plane wall of 5 in thickness and 6 ? area with two surfaces that are 2 maintained at 230°C and 70°C respectively. Determine the heat transfer between the surfaces and temperature gradient across the wall if conductivity of the wall material is16.5 W/(m-K).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.4P: An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a...

See similar textbooks

Related questions

Q: Would the volumetric flow rate in a pipe, assuming laminar flow, be more or less if the fluid were…

Q: How does a heat exchanger work? Where and when will you use a heat exchanger?

A: A heat exchanger is a device in which heat is transferred from one fluid to another. Working:- In…

Q: Wet steam at 200°C and 20% moisture is compressed in an irreversible adiabatic process to a process…

Q: Calculate the tangential stress in the steel.

A: Calculate the tangential stress in the steel.

Q: A machine shaft supported on bearings 11 ft apart is to transmit 288 hp at 200 rpm while subjected…

A: given; transmitted power (P)=288hp =214.76kw…

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Assume F = 660 N, a =…

A: Consider the free body diagram for the member ABC.

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 520 150 60° 60° 370 185 260…

A: To determine the centroid of the given segment.

Q: Assuming a constant flow, the equation governing the transfer of heat energy Q as a function of time…

A: Given : To find : Heat equation

Q: A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

Q: each of 0.15 m radius and 1.9 kg mass). If the system is released from rest when 0= 76°, when rod AB…

Q: Determine the moments of inertia about the y-axis of the circular area without and with the central…

Q: Mechanics of Deformable Bodies The rigid beam of negligible weight is supported by a pin at o and…

Q: The expression for stream function is described by y = x ^ 3 - 3x * y ^ 2 . Indicate whether the…

Q: Would the volumetric flow rate in a pipe, assuming laminar flow, be more or less if the fluid were…

A: Laminar flow through pipe Constant pressure gradient, pd/dz= constant

Q: The steel frame shown has a diagonal brace BD with an area of 1612 sq.mm. Determine the largest…

Q: A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: Differentiate the three modes of heat transfer.

Q: The trapeze/lanyard air drop (t/LAD) launch is a proposed innovative method for airborne launch of a…

A: Given : To find : Angular velocity

Q: Why was Gases and Smoke the cause of 75% of fire- related deaths worldwide? How can you apply this…

A: Given question : Why was Gases and Smoke the cause of 75% of fire- related deaths worldwide? How…

Q: Well-insulated ducts operate at steady state with parameters as shown. The pressure is about 1 atm…

Q: In the figure below, two applied forces are acting at point C where there is a 120 lb and let P =…

Q: Steel balls 10 mm in diameter are annealed by heating to 1,150 K and then slowly cooling to 450 K in…

A: Given Diameter, d = 10 mm Thermal conductivity, k = 40 W/mK Convection…

Q: Pressure drop between two sections of a unifrom pipe carrying water is 9.81 kPa. Then the head loss…

Q: Determine the coordinates of the centroid of the shaded area. y

Q: Steam enters a turbine operating at steady state with a mass flow rate of 10.1 kg min1, a specific…

A: Given data as per qestion m=10.1kg/minh1=3130kJ/kgv1=22m/sh2=2190kJ/kgv2=40m/sz1=3.2mz2=0Q=−1.1kJ/kg…

Q: Determine the x- and y-coordinates of the centroid of the shaded area.

Q: 3. At the instant shown, with an angular velocity of w=6rad/s and an angular acceleration of…

A: Solution - Given data -ω =6 rad/sa =3 rad/sωBC =0.866 rad/s

Q: For oil flow through a pipe, velocity increases O 1, with decrease in area of cross section O 2.…

A: Option : With decrease in area of cross section

Q: A hydraulic system consists of a piston with a 0.64 cm diameter and a second piston with a diameter…

Q: One mole of an ideal gas is kept in a container at an initial pressure of 2 kPa and temperature…

A: find the ratio of heat and work .

Q: Determine the magnitude of the pin force at A. Assume W = 565 Ib, a = 4.1 ft, b = 3.2 ft, r = 8 in.…

A: given; lets take reaction force at A=RAa=4.1ftb=3.2ftr=8in =0.66ftw=565lb

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: Following is not the assumption of Bernoulli Energy Equation

A: option B is the correct answer

Q: By the method of this article, determine the moments of inertia about the x- and y-axes of the…

A: A trapezoidal area is given below,

Q: Using the figure below, find the ff: 1. Crank rotates clockwise at constant rate of 900 rpm.…

Q: Steam is throttled to 0.1 MPa with 20- degrees of superheat. What is the quality of throttled steam…

Q: Air is compressed in an adiabatic compressor from 75 psia and 660 R to 290 psia and 1320 R.…

A: Given Initial pressure, P1 = 55 psia Final pressure, P2 = 270 psia Find Isentropic efficiency

Q: Air enters the diffuser of a turbojet engine with a mass flow rate of 65 lb/s at 9 lbf/in2, 420°R,…

A: Given data as per the question Flow rate = 65 lb/s The pressure ratio for the compressor = 12…

Q: Determine the force (written as a vector) which BC exerts on member AB (a) if the 650-N load is…

A: When a push or pull applied on the object in compressible or tensile manner, it has the ability to…

Q: For solid objects moving through a fluid, turbulence will occur fo Reynolds number greater than 10°.…

A: Critical Reynolds number, Recr=105Length of dolphin, Ld=2.0 mVelocity of dolphin, Vd=6.0 m/sLength…

Q: Consider the right-circular cylinder of diameter D, length L, and the areas A1, A2, and A3…

A: Right circular cylinder: Diameter D Length L Areas A1, A2, and A3 representing the base, inner, and…

Q: A cylindrical steel pressure vessel 200 mm radius with a thickness of 20 mm, is subjected to an…

A: Given: P = 5 MN/m2 t = 20 mm r = 200 mm

Q: The 17-lb link AB is pinned to a moving frame at A and held in a vertical position by means of a…

A: Given data as per the question Mass of link AB =17 lb Maximum tension =10 lb Calculations…

Q: A nylon thread is subjected to a 8.07-N tension force. Knowing that E = 3.25 GPa and that the length…

Q: A 3 m2 hot black surface at 80 C is losing heat to the surrounding air at 25 C by convection with a…

A: Given Area, A = 3 m2 Heat transfer coefficient, h = 12…

Q: 5.45 Two parallel disks of diameter D are brought together, each with a normal speed of V. When…

A: Mass flow rate then is decreasing in the vertical direction because of the plates motion must be…

Q: Example 6: Replace the force and couple system acting on the member shown by an equivalent resultant…

Q: Consider the rectangular cardboard shown in the figure. If you cut a hole in the material and…

A: Correct answer: (A) increases

Q: A petroleum product of viscosity 0.5 Ns/m² and density 700 kg/m³ is pumped from a tank through a…

Concept explainers

Radiation

Radiation can be described as the energy in the form of a particular matter or electromagnetic waves traveling in the air and can be in the form of light, sound, and heat. Radiation can be detected through special instruments like X-rays. The radiation from a cooler object is less intense as compared to the radiation from hot objects.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with dimensions 0.1m0.5m is determined to be 125 W when the surface of the plate is kept at 30C. What is the average convection heat transfer coefficient between the plate and the air?
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
1.29 A spherical interplanetary probe with a 30-cm diameter contains electronic equipment that dissipates 100 W. If the probe surface has an emissivity of 0.8, what is its surface temperature in outer space? State your assumptions in the calculations.
Determine the rate of heat transfer per meter length from a 5-cm-OD pipe at 150C placed eccentrically within a larger cylinder of 85 magnesia wool as shown in the sketch. The outside diameter of the larger cylinder is 15 cm and the surface temperature is 50C.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
A horizontal pipe having a surface temperature of 67 °C and diameter of 20 cm is buried at a depth of 1 m in the earth at a location where k = 1.8 W/m-°C. The earth surface temperature is 15 °C. Calculate the shape factor if the pipe length is 10 m.
Addition of fins may not necessarily increase the heat transfer from a surface; itmay even decrease the heat transfer. Comment on this stateme
HEAT TRANSFER A mild steel steam pipe with an outer diameter of 11.43 cm and inner diameter of 10.226 cm is covered with 2.5 cm layer of 85% magnesia. The outer surface temperature is 65°C. Determine the heat loss per hour per meter of the pipe. Assuming that the steam is saturated at the pressure of 1.14 MPa, its temperature is 185.68°C. k (steel) = 55.4; k (magnesia, 85%) = 0.0727 W/m-K
Question 1:A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg=1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15oC and -20oC, respectively, ona cold winter day, what is the rate of heat loss throughthe glass? To reduce heat loss through windows, it iscustomary to use a double pane construction in whichadjoining panes are separated by an air space. If thespacing is 10 mm and the glass surfaces in contact withthe air have temperatures of (last two digit of your Registration number) oC and -15oC, what isthe rate of heat loss from a 1 m x 2 m window? Thethermal conductivity of air is ka=0.024 W/m.K.
An experiment is undertaken to determine the thermal conductivity of an unknown material. The material is 5 cm thick and has a diameter of 15 cm. It is placed on a hot plate of equal diameter where the surfaces temperature is maintain at 60oC. The outer surface temperature is 24oC, and the power used by the hot plate is 45 W. Determine the thermal conductivity of material.