In 33kV system, inductance and capacitance are 1.2 H and 0.02uF respectively. What is the prospective instantaneous voltage across CB when arc gets interrupted at an instantaneous current of 20A.

Q: A. A Wien-Bridge oscillator with a lead-lag circuit is shown in Figure 1. 6.8 V 6.8 V Ry 47 k 100 ki...

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for...

Q: Two lamps 5cd and 20cd are 15pcm apart. At what point between them will be the same illumination pe ...

A: The solution can be achieved as folows i.

Q: A three-phase, 3-wire, 120V, 60Hz, delta connected AC generator is applied to a balanced load having...

A: First calculate phase impedance parallel combination of resistor and capacitor.  By ohms law current...

Q: Question 5 Find the voltage required to send 2 A through a parallel combination of a 20-0, a 30- N, ...

A: 1. Find equivalent resistance 2. Draw the equivalent circuit 3. Use ohm's law find the voltage

Q: 2. Use KCL and KVL to: a. Establish the current equations at points x and y b. Establish the voltage...

A:

Q: What is the error in the ammeter which reads 3.25A in a circuit having a series standard resistance ...

A: % error = Actual computation - meter readingActual computationX 100 %

Q: 15. A factory takes a load of 2,400 kva at 0.6 lagging power factor. A synchronous motor having an i...

A:

Q: 4. When supplied with current at 240-V, single-phase at 50 Hz, a certain inductive coil takes 13.62 ...

A:

Q: Choose one appliance/electronic device that needs application before it can be used and explain why

A:

Q: A pole zero plot has one zero in origin and two poles located at 2 and -1. So the system is a. Type ...

A: In this question,  Choose the correct option We know Type of the system is number of poles at the or...

Q: A

A: Since the value of each resistor is not mentioned, we will assume that Each resistor value to be equ...

Q: Find VD1, VD2 and I

A: In this question we will find diode voltage and current through si diode...

Q: 17. A manufacturing plant has a load of 3,600 kva at a lagging power factor of 0.707. A 500-hp synch...

A:

Q: A four port network has a scattering parameters as follows. check the attached figure then answer t...

A: According to the question, for the given scattering matrix, we need to check (i) Is this network rec...

Q: A circuit takes a current of 8 A at 100 V, the current lagging by 30° behind the applied voltage. Ca...

A:

Q: Three resistors are connected in parallel across a 40 V source. The values of the resistors are 620n...

A: Given data, V=40 V, R1=620 Ω, R2=750 Ω, R3=820 Ω (a) According to question all the resistors are con...

Q: I) Convert from Binary to Decimal a) 11101001112 (b) 100101010.110012

A: Given a)11101001112

Q: 15. For the voltage-divider bias configuration of Fig. 4.125, determine: IBe b. Ico VCEQ d. Vc- e. V...

A:

Q: A single phase half wave uncontrolled rectifier is supplied using 220 V,60 Hz supply with a pure res...

A: Given : VS=220 Vf=60 HzRL=10 Ω

Q: Find the ABCD constants of a network consisting of a 500-ohm resistor shunted across its sending end...

A: In this question we will first make circuit diagram with given data and will find ABCD constants...

Q: The ground test lead/connector should be inserted on the socket. 20 A max V/N/Hz COM

A: Answer is option 4 : COM

Q: Equivalent circuit with a current source

A:

Q: An ammeter (instrument that measures current) carries 0.05 A and is in parallel with a shunt resisto...

A: (a) Consider the KCL suggest that the total current that enters the node is equal to the current tha...

Q: The network shown is initially unenergized. At t = 0, the switch is closed. Find the differential eq...

A: Given v(t) = 10cos4t                         iL0 =0AVL0 =0Vfor t >0, Apply Laplace transform, Z...

Q: UT (c) Assume that you have two numbers A and B that are represented in 4-bit 2's UTM UTM 2's comple...

A:

Q: 3. An inductive coil having a resistance of 15 Q takes a current of 4 A when connected to a 100-V, 6...

A:

Q: A 220V. dc series motor is running at a speed of 800 rpm and draws 100 A. Calculate at what speed th...

A: Supply voltage, V = 220 V Initial speed of the motor, N1 = 800 r.p.m Armature current at speed N1, I...

Q: Two identical 50 Hz, 400 V, 3Φ , alternators share equal power jointly delivered to a balance three-...

A:

Q: Using a circuit diagram and output waveform, describe the mechanism of a square wave oscillator.

A:

Q: )  A 50 cm length 50 ohms coaxial cable is terminated with an antenna having an impedance of 100 + j...

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for y...

Q: The transmission line in Figure Q.1 (a) now is shorten to L=λ/4 and the input impedance Zin is set t...

A:

Q: ohms transmission line of length L=λ/2 in Figure Q.1 is to be used in RF testing. Determine the inpu...

A:

Q: 3. A series circuit composed of a 0.2 henry inductor and a 74 micro farad capacitor is connected to ...

A: This question belongs to circuit theory . It is based on the relation between voltage , current and ...

Q: explain what are the differences between an N-type and P-Type Junction Diode.

A:

Q: List and describe 7 properties that an appropriate mediator used in sensor design should possess.

A: Sensors are defined as the devices which are used to detect something from environment as an input a...

Q: A PMMC instruments has a coil of dimensions 12 mm × 10 mm. The flux density in the air gap is 0.20 w...

A:

Q: 5. What will be the output of the following code?

A: Given information: The following lines of code are given: for i=1:3 i=i-1 end From the given options...

Q: A three-phase Y-connected alternator delivers a unity power-factor load at 220 volts. If the synchro...

A: In this question, we need to calculate a. calculate the generated voltage b. calculate the percent r...

Q: Q3: Find I, in the network in fig.(3) using superposition. YA

A:

Q: Satisfy the given table with three inputs using CMOS Logic. Write a clear logic diagram and label th...

A:

Q: An X band copper rectangular waveguide (22.9 mm × 10.2 mm) is filled with dielectric material having...

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for y...

Q: QI. Estimate the power consumed by the lamp shown in Figure 5. Battery E = 18 V Lamp R=30 Figure 5

A: This question belongs to circuit theory . It is based on the concept of power consumption in the bul...

Q: Compare hybrid model circuit and re model circuits. Which circuit are you going to recommend in solv...

A:

Q: A step up converter is operated with a duty cycle of k = 0.75. The input voltage is V,= 20V, and the...

A: Duty cycle, k = 0.75, Input voltage, Vs = 20 V Inductance, L = 5 m H Load resistance, R = 20 Ω The m...

Q: 26.11 · In Fig. E26.11, R1 = 3.00 N, R2 = 6.00 N, and R3 = 5.00 2. The battery has negligible intern...

A:

Q: A Step aown converter is feeding an inductive load with R-10 Ohms, Le15 mH and E15V. The supply is v...

A: Given thatVs=200vfs=10kHzTs=1fs=110k=0.1m sec Duty cyce k=0.5R=10ΩL=15mH

Q: Propose a digital to analogue converter circuit using 1 op amp and 3 resistors (R1=200 kΩ, R2 =100 k...

A: Here is your answer! I hope this will help you.

Q: A surface has an area of 3 m2 and its normal is along the direction of (9,6,9). If there is a unifor...

A: Given : Surface area, A=3 m2 The surface is having its normal direction along (9,6,9). The electric ...

Q: (a) Consider the minterm function F(A, B, C) = Em(1,3,4,7) Implement the circuit using 4-to-1 and 2-...

A:

Q: In the circuit, the switch has been open for a long time. Calculate the time-dependent equation of t...

A: Given circuit is

Star Delta Conversion

Find the input resistance between points A and B of the following resistive network: