In a portion of the square, 2-D finite difference mesh shown, node 2 is located on an insulated edge. The thickness and thermal conductivity of the region are 1.50 mm and 20 W/m-K, respectively. If there is a point heat source of 1.2 W at node 2, calculate the steady temperature of node 2. T, = 40°C T = 52°C T= 60°C 0,= 1.2 W 8 = 1.50 mm k= 20 W/m·K 3

In a portion of the square, 2-D finite difference mesh shown, node 2 is located on an insulated edge. The thickness and thermal conductivity of the region are 1.50 mm and 20 W/m-K, respectively. If there is a point heat source of 1.2 W at node 2, calculate the steady temperature of node 2. T, = 40°C T = 52°C T= 60°C 0,= 1.2 W 8 = 1.50 mm k= 20 W/m·K 3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

High Voltage Technique For the most puncture-related arrangement of a concentric spherical electrode system with a voltage of 100 kV to be applied between the electrodes and with Ed=80 kV/cm (insulator puncture strength), Emax = 0.6. Ed a) Inner and outer sphere radii, b) Maximum and minimum field strengths, c) Equivalent electrode opening and utilization factor, d) Its capacity (Ɛ0=8,854x10-12 F/m, Ɛr=1) and insulator volume, e) By keeping the outer sphere radius constant, calculate the inner sphere radius value range that can be used in the system without discharge. ANSWERS: a) r1=4.16 cm, r2=8.32 cm b) Emax=48 kV/cm, Emin=12 kV/cm c) α=2.08 cm, η=0.5 d) C=9.257 pF, Vinsulator=2110 cm3 e)1.53<r1<6.8 cm
96 kg of ice has accumulated over 40 meters of a conductor whose 40 meters are 46 kg in a naked state. This conductor is III, where k=0.3. is in the ice zone.Since it is known that it is calculated with qb=k√d (kg/m) and the conductor is exposed to wind force at the same time with ice on it, calculate the q+bw value as kg/m.Frosted diameter D=√d2+216.46 qb mm (d bare conductor diameter, qb ice load in kg/m)Wind load qw=p x d x c x 10-3 N/m (no ice condition, different formula will be used in icy condition.)It will be taken as c=2 and p=294.3 N/m2
In a three layered, cylindrical electrode system, 100 kV is applied to the inner conductorwhile the outer conductor is grounded. Radii of cylinders in this system are: r1 =1 cm, r2 =1.5cm, r3 =3 cm, and R =5 cm. Relative dielectric constants of layers are r1 = 5, r2 = 3 and r3 =2.5 respectively;a) Calculate maximum and minimum field strengths across each layer.b) If R=5 cm and r3 =4.5 cm, for uniformly stress condition find the new values of r1 and r2and the thickness of each layer.
The outer radius of a coaxial cylindrical electrode system is given in 32 cm. The system is the most suitable sized according to puncture. Penetration of the insulator between the cylindrical layers Its strength is Ed = 72 kV / cm and the relative dielectric constant of the insulator is Er1 = 52 c) -Calculate the actual distance (d) of the system, the utilization factor (n) of the electrode aperture (alpha)? (E0 = 8,854x10-12 F / m)
The relative dielectric coefficient of the planar electrode system given in the figure is Er = Er0 n. It changes linearly according to the x relation. Ero == 8,3 for this electrode system; n = 1.7 cm and the gap between the electrodes is given as a = 3 cm. 28 kV direct voltage is applied to this planar electrode system, so find the amplitude of the electric field strength at the point A (2.5cm, 3cm). (Edge effects will be neglected, electrode length b <15 cm)
3.(Part I) A 50 V voltage generator at 20 MHz is connected to the plates of an air dielectric parallel-plate capacitor with a plate area of 2.8 cm^2 and a separation distance of 0.2 mm. Find the maximum value of displacement current density and displacement current. (Part II) A dielectric material with permeability that of free space, permittivity = 9xpermittivity of free space, conductivity = 4 S/m, is placed between the plates of a parallel-plate capacitor. Calculate the frequency at which the conduction and displacement currents are equal.
The outer radius of a concentric spherical electrode system is given as 22 cm. The system is most suitable sized for perforation. The puncture strength of the gas between the spherical layers is Ed=82 kV/cm and the relative dielectric constant of the gas is Ɛr1=1. a)- Calculate the capacity of the system and the highest voltage that can be applied to the system without rupture Determine what should happen. b)- For the case of U=120 kV application, the maximum and minimum occurring on the system Calculate the electric field values?
A rectangular aluminum bus bar is 0.9m long, 0.15 m wide, 0.013m (1.3cm) thick. If the current in the bus bar flows along its length, and the conductivity (σ) of aluminum is 3.57x10^8 S/m. Calculate the bus bar resistance in µΩ.
The relative dielectric coefficient of the planar electrode system given in the figure is Er = Er0 - n. It changes linearly according to the x relation. Er0 = 7.2 for this electrode system; n = 1.8 cm ^ -1 and the gap between electrodes is given as a = 3 cm. 26 kV direct voltage is applied to this planar electrode system, so find the amplitude of the electric field strength at point A (2.7cm, 3cm). (Edge effects will be neglected, electrode length b <15 cm) y 4 a (cm) -> electrode electrode
Hi, I need help with this question please Consider a coaxial cable of length l = 50 cm, inner radius of a = 3 cm, and outer radius of b = 5 cm. Due to the conductivity of σ = 0.05 S/m of the dielectric material, a total current of I = 1 mA flows radially outward between the two conductors. Find:a) the current density as a function of r,b) the electric field between the two conductors as a function of r, c) the voltage between the two conductors.
The outer radius of a coaxial cylindrical electrode system is given as 38 cm. The system is the most suitable sized according to puncture. Penetration of the insulator between the cylindrical layers Its strength is Ed = 78 kV / cm and the relative dielectric constant of the insulator is r1 = 40. a) - Calculate the capacity of the system and get the highest possible application without puncture to the system. Please respect what the voltage should be. b) - For the case of U = 180 kV application, the maximum and minimum occurrence on the system Calculate the electric field values? c) -Calculate the actual distance (d) of the system, the utilization factor (n) of the electrode aperture (alpha)? (Ɛ0 = 8,854x10-12 F / m)
A 132kV line with 1.956 cm diameter polished conductors is built so that corona takes place if the line voltage exceeds 75kV per phase. If the value of potential gradient at which ionization occurs cab be taken as 32kV (Max) per cm and air density factor 0.91. Distance between conductors is 1.21 meters. The corona loss is