In a relative density test, the following values are recorded: Dry mass = 3017 g Submerged mass = 1050 g Saturated, Surface Dry (SSD) mass = 3033 g Find the relative density values (RDapparent, RDbulk, and RDSSD) by first completing the phase diagram. (write answers in the phase diagram to the nearest whole number. Write the relative density answers to two decimal places.) VOLUME MASS Va = cm3 AIR Ma = grams Vw = cm3 WATER Mw = grams Vs = cm3 SOLIDS Ms = grams VT = cm3 MT = grams RDapparent = RDbulk = RDSSD =

In a relative density test, the following values are recorded: Dry mass = 3017 g Submerged mass = 1050 g Saturated, Surface Dry (SSD) mass = 3033 g Find the relative density values (RDapparent, RDbulk, and RDSSD) by first completing the phase diagram. (write answers in the phase diagram to the nearest whole number. Write the relative density answers to two decimal places.) VOLUME MASS Va = cm3 AIR Ma = grams Vw = cm3 WATER Mw = grams Vs = cm3 SOLIDS Ms = grams VT = cm3 MT = grams RDapparent = RDbulk = RDSSD =

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter9: Mass And Mass-related Variables In Engineering

Section: Chapter Questions

Problem 34P

See similar textbooks

Similar questions

Specific gravity is calculated by the formula: S.G. = density of sample/density of water at a given temperature Using the table below, compute the specific gravity of assigned samples (density data provided) at 4 deg., 20 deg., and 25 deg. Centigrade as standards. Tab. 1. Temperature dependence of distilled water density ρH2O. t [°C] ρH2O [g/cm3] 15 0.99996 16 0.99994 17 0.99990 18 0.99985 19 0.99978 20 0.99820 21 0.99799 22 0.99777 23 0.99754 24 0.99730 25 0.99705 Sample Density a. Citronella 0.882 b. Eucalyptus 1.465 c. Lemongrass 0.890 d. Tea Tree Oil 0.895 e. Wintergreen 1.182
1. A certain liquid has a unit weight of 57 KN/m^3. Compute the mass density.Unit of the correct answer: kg/m^3Decimap Places required in the final answer: 3
Calculate temporary and permanent hardness of a sample of water, which on analysis is found to contain the following: Ca(HCO3)2 = 16.2 mg/L; Mg(HCO3)2 = 7.3 mg/L; MgCl2 = 9.5 mg/L; CaSO4 = 13.6 mg/L.
USING FOL Differential Equation APPLICATION SOLVE THE FOLLOWING PROBELM AND SHOW COMPLETE SOLUTION AND FINAL ANSWER.In a tank of 100 liters of brine containing 50 kg total dissolved salt. Pure water is allowedto run into the tank at the rate of 3 liters a minute. Brine runs out of the tank at the rateof 2 liters a minute. The instantaneous concentration in the tank is kept uniform bystirring. How much salt is in the tank at the end of 1hour?
From the given figure. From the e-log p plot, two points were given. p1 = 80 kPa e1 = 0.60 p2 = 150 kPa e2 = 0.40 Determine the Liquid Limit.
Need answer ASAP. Please show your solution in detailed and clear. I. If a certain liquid weighs 6.80 kN/m³. Compute the following: 1) Mass density in kg/m³ . 2) Specific volume 3) Specific gravity relative to water at 20°C?
Please provide a clear solution. Thank you! If a certain liquid weighs 6.80 kN/m³. Compute the following: a)Mass density in kg/m³ b)Specific volume c)Specific gravity relative to water at 20°C?
In a falling head permeability test, head causing flow was initially 50 cm and it drops 2 cm in 5 minutes. How much time in minutes required for the head to fall to 25 cm ? Provide a diagram. a.49.4 b.89.4 c.98.4 d.84.9
Write the simplified equation for estimating TSS as a function of Q. Determine the 2 parameters associated with this relationship if TSS is 89 mg/L at Q = 8 m 3 /s and TSS is 109 mg/L at Q = 12 m 3 /s? What will be the TSS if Q is 20 m3 /s?
A 5-gram sample was placed in a graduated cylinder filled with water, where a rise of 4.5 ml was observed. 1. What is the volume of displaced liquid? 2. What is the weight of displaced water? (Enter the complete computed value) 3. What is the specific gravity of the solid?
The inside diameter of an open cylinder tank was measured. The results of four replicate measurements were 5.2; 5.7; 5.3; and 5.5 m. Measurements of the height of the tank yielded 7.9; 7.8; and 7.6m. Calculate the volume in liters of the tank and the standard deviation of the result.
A cube of material is 4 in. on a side and floats at the interface betweenkerosene (SG=0.82) and water, as shown.a. Find the specific gravity of the material. b. How much weight is required to fully submerge the cube underwater? Show prssure diagram with complete solution, correct formula, and conversions/