In an engineering structure shown in figure below, the material used to manufacture the cable AB is tested by tensile -test machine and the following result were recorded, knowing that the cable material having the following parameters, Determine the stress in the cable and its extension under the load shown? Original length (mm) Original diameter(mm) load (KN) 0 12.7 25.4 38.1 50.8 76.2 89.1 92.7 102.5 107.8 119.4 128.3 149.7 159 160.4 159.5 151.5 124.7 50.8 12.8 length (mm) 50.8 50.825 50.851 50.876 50.902 50.952 51.003 51.054 51.181 51.308 51.562 51.816 52.832 53.848 54.356 54.864 55.88 56.642

In an engineering structure shown in figure below, the material used to manufacture the cable AB is tested by tensile -test machine and the following result were recorded, knowing that the cable material having the following parameters, Determine the stress in the cable and its extension under the load shown? Original length (mm) Original diameter(mm) load (KN) 0 12.7 25.4 38.1 50.8 76.2 89.1 92.7 102.5 107.8 119.4 128.3 149.7 159 160.4 159.5 151.5 124.7 50.8 12.8 length (mm) 50.8 50.825 50.851 50.876 50.902 50.952 51.003 51.054 51.181 51.308 51.562 51.816 52.832 53.848 54.356 54.864 55.88 56.642

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

True-False Questions2. Floating can be done as soon as the straightening operation is concluded. ( )3. The center portions of form ties are temporally embedded in a concrete wall. ( )
!!!Show Complete Solutions and FBD!!! What is the bending stress in the beam 1.8 meteres from point A?a. 9.60Mpab. 8.60Mpac. 7.68Mpad.10.24Mpa What is the bending stress 20 mm from the top of the beam 1.5 meters from point A? a. 9.247Mpab. 7.225Mpac. 10.442Mpad.4.838Mpa What is the shear stress in the beam at point A?a. 0.48Mpab. 0.33Mpac. 1.57Mpad. 0.80Mpa
What is the maximum shear flow (qmals) that can occur in the section if it is subjected to a shear force of V = 80 kN? The dimensions of the section are: b = 450 mm, h = 250 mm, t = 25 mm. Please note that shear flow is typically measured in N/mm and it represents the distribution of shear stress along the section. a) 176,3 b) 184,7 c) 210,5 d) 225,9 e) 203,5
A line is recorded as 475.25 m long. It is measured with a 6.5 N tape which is 30.492 m long at 680F under a 10 lb. pull supported at end points. During measurement the temperature is 4.50C and the tape is suspended under a 71 N pull. The line is measured on 3% grade. What is the true horizontal distance? Modulus of elasticity of the tape is 1.93 X 108 KPa and cross-sectional area of tape is 0.0284 cm2. Coefficient of expansion of the tape material is 0.0000116 m/0C.
A steel cable 31 mm in diameter and 15.25 m long is to lift a 0.2 MN load. What is the length of the cable during lifting? The modulus of elasticity of the steel is 210 Gpa.
I tried to solve the problem using your solution and got a different answer. Also where is the angle in degrees made by cable with the horizontal at the supports?
Problem 1 What force is required to punch 20-33 diameter hole in a plate that is 25mm thick? The shear strength of the plate is 350 MN/m2? ANS: V= 550,000N
Refer to the photo provided and please make sure your handwriting is readable. Given E = 200 GPa and figure shown. 1. What is the maximum displacement? 2. Tensile stress at cable. 3. What is the safest load applied at B if the allowable stress in the cable is 125 MPa
Answer the ff about staad pro. a). Can we still analyze and design a structure if we did not use reference loads? explain why b). Why is there no earthquake load in the y direction of staad? c). What does it mean if there is a question mark attached to an item in staad? d).What is the difference between error, warning and notes in staad? e). What type of structural member will you place to act as a shearwall f).How can we specify different floor load values on different portions of a slab.
A uniform flexible cable 350m long weighs 6000 N. The resultant tensions at the ends of the cable are10,000 N and 12,000 N, respectively. What is the difference in elevation of the two ends? How far is the lowest point of the cable below the lower end? What is the horizontal distance between the ends?
The copper pipe shown in the figure has an outside diameter of 3.375 in. and a wall thickness of 0.386 in. The pipe is subjected to a uniformly distributed torque oft= 71 Ib-ft/ft along its entire length. Using a = 2.00 ft, b = 4.50 ft, and c= 9.25 ft, calculate
A cable 45.4 m long is carrying a uniformly distributed load along its span. If the cable is strung between two posts at the same level, 40 m apart, compute the smallest value that the cable may cable may sag.