In an oil cooler of the counter flow type 5000 kg per hour of oil of specific heat 0.6 are cooled from 40°C to 24°C by means of 6000 kg per hour of water which enters at 15°C.find the cooling surface required if the overall coefficient of heat transmission is 3000 kcal/m^2 hour °C.

In an oil cooler of the counter flow type 5000 kg per hour of oil of specific heat 0.6 are cooled from 40°C to 24°C by means of 6000 kg per hour of water which enters at 15°C.find the cooling surface required if the overall coefficient of heat transmission is 3000 kcal/m^2 hour °C.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.16P

See similar textbooks

Related questions

Q: Question 6: Find the required length of a 5 cm-diameter tube to heat water from an inlet temperature…

A: Given data: Diameter of the pipe, d=5 cm=0.05 m Let 'L' be the length of the pipe. Inlet temperature…

Q: Water at T, = 24°C is heated to T, = 74°C by passing it through an alternating 2. %3D array of…

Q: Determine the power required for a forced draught and induced draught fan in a boiler having coal…

A: Given data Coal consumption = 25 kg/min = 0.4167 kg/sAir/fuel ratio = 19Draught required = 32.2 mm…

Q: 2 mon. Mw: 17 Water at 33 °C flows in a straight horizontal pipe in which there is no exchange of…

A: Given data: ◆ Diameter of pipe at inlet and exit: D1 = 1.5 inch , D2 = 2 inch ◆ The velocity of…

Q: 147 Find the volumetric efficiency and estimate the approximate clearance of 45.75 x 45.75-cm,…

Q: Determine the temperature of hot flue gases & efficiency of chimney for maximum discharge through…

A: Given:Height of the chimney, h=80 mTa=27+273=300 KTemperature of hot gas, Tg=110+273Tg=383 Kmass of…

Q: A perfectly stirred cylindrical tank (D -2 m, H= 1.6 m) with steam jacket, is initially full of a…

A: Given data Aperfectly stirred cylindrical tank (0-2 m, H=1,6 m) with steam jacket, is initially…

Q: The turbine's inlet is coupled to a steam throttling valve with inlet conditions of 2MPa and 400C.…

A: Write the given data. P1=2 MPaT1=400 °CW=200 kWQR=100 kWT2=300 °Cm˙=1 kg/s

Q: Air is used in a Carnot engine where the volumes at the beginning of the constant temperature heat…

A: given data- V2 = 6.73 cubic cm V3 = 0.456 cubic cm to determine - efficiency of the engine

Q: 3. A 6 in x 20 ft uninsulated B.I pipe conveys steam at 385 °F with an average ambient temperature…

A: Given, Do=6.625 in=6.62512 ft=0.552 ftDi=5.761 in=5.76112 ft=0.48 ft L=20 ft k=30 BTUhr.ft.0Fhi=1000…

Q: An industrial adiabatic heat exchanger utilizes cold-water stream to cool down the waste-hot air…

Q: In an oil cooler of the counter flow type 5000 kg per hour of oil of specific heat 0.6 are cooled…

Q: A Carnot engine receives 130 BTU of heat from heat reservoir at 700oF and rejects 49 BTU of heat.…

A: Given Data⇒ Heat received QH=130 Btu TH=7000F=644.261 K Heat rejected QR=49 Btu

Q: At the intake to a turbo-jet engine the air temperature is at pressure p 1 = 1.013 bar and…

Q: Determine the power required for a forced draught and induced draught fan in a boiler having coal…

Q: A reaction turbine used 9,000 kg of steam per hour. At one point in the turbine, the blades are 20…

A: Given data mass flow rate of steam (m˙) = 9000 kg/hr h = 20 mm P=0.32 MPa x=0.95 V1 = 120 m/s…

Q: A large fridge freezer is to extract 80 kJ of energy every second from inside of the fridge,…

A: We are suppose to solve only 3 subparts. Please post other parts as a separate question.

Q: Used to cool the cockpit of a refrigerated aircraft (33 tons of simple air refrigeration). The…

Q: Q8/ A turbine that uses steam drives an electric generator. The inlet steam flows through a…

A: Given:Inlet diameter of pipe, di=10 cm or 0.10 mexit diameter of pipe, de=25 cm or 0.25 mmass flow…

Q: An ice plant produces 10 tons of ice per day at 0°C using water at room temperature of 27°C.…

A: There are two types of heat, 1. Specific heat and 2. Latent heat In this question, we convert the…

Q: Speed of the turbine in Revolutions per minute. Power developed in kilowatts

A: Given: Reaction turbine ms=9000 kg/hrh=20 mm=0.02 mP=0.32 MPax=0.95vf1=0.7uvf2=0.76uleakage of…

Q: For the production of high-speed trains at the SIEMENS company in Krefeld, considerable amounts of…

Q: Q6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the…

Q: Feed water heaters are used to preheat water before entering the boiler of a steam power plant by…

A: Assumption took to this question:- 1. Steady flow device 2. Kinetic and potential energy are…

Q: A two-stage compressor has water-jacketed cylinders and a water cooled inter cooler. The compressor…

Q: Air at 27°C enters the channels of a finned air heater with a velocity of endplates are both kept at…

A: Given, T∞ = 27oC Ts = 127oC W = 200 mm B = 100 mm t = 1 mm L = 15 mm S = 3 mm ηf = 0.98 U = 5 m/s cp…

Q: Water at 90C is being pumped from a large storage tank at 1 atm abs at a rate of 0.189 m3/min by a…

Q: Steam at 15 bar and 300°C expanded in a nozzle till its pressure falls to 1 bar. If the 12% of…

A: The solution is in next step

Q: An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps…

A: Option D is right

Q: Helium at 30°C and 100kPa flows to a compressor at a rate of 2kg/s. The Helium at the outlet is at…

A: Given data: P1=100 kPaT1=30°Cm˙=2 kg/sP2=200 kPaT2=150°C Need to determine the power required to…

Q: A forced-circulation triple-effect evaporator using forward feed is to be used to concentrated a 10…

Q: Q3: pressure. During compression the heat loss to surrounding is estimated to be 5% of compression…

Q: Air enters a cooler at 1450C and at a pressure of 3 bar and is cooled to 450C by passing through…

Q: The isentropic heat drop in the nozzle of an impul: steam turbine with a nozzle efficiency 0.9, blad…

A: Given:Nozzle efficiency, η=0.9Blade-velocity ratio, uV2=0.5mean blade velocity,u=150 m/s

Q: Air (R = 0.3074 psia.cf/lbm.R) is compressed from 14.7 psia and 60°F to a pressure of 150 psia while…

A: Given data P1=14.7 psiaT1=60°F

Q: Dry saturated steam at 12 MPa enters a superheater at a rate of 211907 kg/hr and leaves at 512°C.…

Q: Hot spring water is used to operate the heat engine in a power station. If the hot spring water is…

A: Given data: The temperature of hot spring water is TH=95°C The temperature of atmosphere is T∞=20°C…

Q: Q3→ Steam enters a steam turbine at a pressure of 4 MPa and a flow rate of 25 kg / s at 450 ° C. At…

A: The turbo generator is a device used to generate mechanical energy using heat in the form of fluid.…

Q: Feed water heaters are used to preheat water before entering the boiler of a steam power plant by…

Q: Water is flowing in a tube "D= 3 cm, L= 5 m" and is to be heated from 15°C to 47°C by applying a…

Q: Determine the power required for a forced draught and induced draught fan in a boiler having coal…

Q: - Q4// An open gas turbine plant works between the fixed absolute temperature limits 300K and 1500K,…

Q: A (293 MW) steam power plant of the pressurized-water Nuclear reactor type uses Once-Through…

A: According to the question, we have Power of the steam power plant, P=293MW change in temperature,…

Q: An air compressor compresses atmospheric air at 0.1 MPa and 27°C by ten times of inlet pressure.…

Q: Q6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the…

Q: Question attached

A: Internal Combustion Engine: Internal combustion engine mainly known as IC Engine. In this kind of…

Q: Q3: An air compressor compresses atmospheric air at 0.1MPA and 270C by 10 times of inlet pressure.…

Q: In refrigeration process, a region is cooled and the temperature was maintained at -15oC. The…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At the intake to a turbo-jet engine the air temperature is at pressure p 1 = 1.013 bar and temperatureT 1 = 220 K and the air velocity (relative to the engine) is v 1 = 200 m/s. The compressor pressure ratior p = 10 and gas is intended to exit the combustor at 1250 K. Estimate all temperatures and pressuresin the system, and the thrust developed by a heat input of 100 kW
The turbine's inlet is coupled to a steam throttling valve with inlet conditions of 2MPa and 400C. 200 kW of power may be generated by the turbine, and 100 kW of heat can be removed from the system. Assuming a mass flow rate of 1kg/s and a steam exit temperature of 300C, calculate the exit turbine pressure
Hot fluid enters at a flow rate of 3 kg/sec with an inlet temperature of 150 C while cold fluid enters 5 kg/sec and with an inlet temperature of 60 C. Determine the maximum heat transfer that can happen during the heat exchange process? Take specific heat value of the fluid as 2000 J/(kgC)
A steam turbine operates with inlet conditions of 500 C and 2 MPa, and exit conditions of 10 kPa and x=0.95. If the required turbine work per kilogram of steam flow is 900 kj/kg. calculate the magnitude of heat transfer from the turbine per unit mass of steam.
Furnace walls are lined by 3 layers: firebrick with a thickness of 6 in (k=0.95 Btu/h.ft. F), insulating brick (k-0.4 Btu/h.ft.°F) and common brick (k=0.8 Btu /h.ft.°F) Firebrick inlet temperature, T₁ = 1800°F, maximum insulating brick temperature, T₂ = 1720°F and T3 = 280°F. 1. Calculate the thickness of the insulating brick layer. 2. If the common brick is 9 in, calculate the exit temperature.
Air at 20°C is hydrodynamically fully developed as it flows in a 1 cm I.D. pipe. The average velocity is 0.7 m/s. If it enters a section where the pipe wall is at 60°C, what is the temperature 0.25 m farther down stream?
Consider a turbojet-powered airplane flying at a standard altitude of 4 km. The inlet and exit areas are 0.82 m^2 and 0.45 m^2. The velocity, pressure, and temperature of the exhaust gas are 300 m/s, 230,000 Pa, and 830 K, respectively. Calculate the thrust of the turbojet. Detailed solution pls
At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg.
A fan is used to transport CO2 gas (MW = 44 g/mol) gas at rest @ 700mmHg. At the discharge end, the pressure is 765mmHg, and the velocity is 100 m/s. Assuming the flue gas behaves ideally, and the process is isothermal, with the temperature maintained at 100C. Determine the theo. power required to move 45000 m /h of the flue gas.
A stationary temperature probe inserted into a duct where air is flowing at 190 m/s reads 85°C. What is the actual temperature of the air?
The maximum flow rate of standard shower heads is about 3.5 gpm (13.3 L/min) and can be reduced to 2.75 gpm (10.5 L/min) by switching to low-flow shower heads that are equipped with flow controllers. Consider a family of four, with each person taking a 5-min shower every morning. City water at 15°C is heated to 55°C in an electric water heater and tempered to 42°C by cold water at the T-elbow of the shower before being routed to the shower heads. Assuming a constant specific heat of 4.18 kJ/kg·°C for water, determine the amount of electricity that will be saved per year, in kWh, by replacing the standard shower heads with the low-flow ones.
The maximum flow rate of standard shower heads is about 3.5 gpm (13.3 L/min) and can be reduced to 2.75 gpm (10.5 L/min) by switching to low-flow shower heads that are equipped with flow controllers. Consider a family of four, with each person taking a 5-min shower every morning. City water at 15°C is heated to 55°C in an electric water heater and tempered to 42°C by cold water at the T-elbow of the shower before being routed to the shower heads. Assuming a constant specific heat of 4.18 kJ/kg·°C for water, determine the ratio of the flow rates of the hot and cold water as they enter the T-elbow.