In figure shown, use left end of the beam as reference and assume the upward reaction provided by the ground to be uniformly distributed. (a) Write the shear-force and bending-moment equations (not simplified and simplified (b) draw the shear-force and bending-moment diagrams 98 kN 50 kN/m 50 kN/m ) at each segment |B E . Label all significant points on each diagram. 1.5 m 2.5 m 2,5 m 1.5 m

In figure shown, use left end of the beam as reference and assume the upward reaction provided by the ground to be uniformly distributed. (a) Write the shear-force and bending-moment equations (not simplified and simplified (b) draw the shear-force and bending-moment diagrams 98 kN 50 kN/m 50 kN/m ) at each segment |B E . Label all significant points on each diagram. 1.5 m 2.5 m 2,5 m 1.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Applying the (AMM) Area Moment Method Approach. Consider 150 mm x 200 mm section and E = 80 GPa. Round off to two decimal places a. Vertical Reaction at C in kN.b. Slope of the elastic curve at support C in degrees.c. Deflection at point B in mm.d. Deflection at point D in mm. Show organized solutions
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
Q1/Find the horizontal displacement at C . and @y by using Virtual Work Method, i you know E - 200 GPa, I - 25°(10% mmé , (P KN)
Can you help me with this, please show complete clear solution A barge is pulled by 2 tugboats. If the resultant of the force exerted by the tugboats is a R-lb force directed along the axis of the barge calculate the tension of each rope. Given: R = 3800 Angle A = 36° Angle B = 26°
6. A simply supported beam carries a concentrated load of 24 kN at 6 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees. ROUND OFF TO FIVE DECIMAL PLACES.
PROBLEM 03In figure 03, determine the following.components of force P=150KN:a. Normal and Tangential components with.respect to the inclined surface,b. Rectangular components, andc. Components along with a’-axis (blue line),.and b’-axis (green line).
Replace the loading system by an equivalent resultant force and couple moment acting at point ?. Length AB = 1m Length BC = 2m F1 = 80 N F2 = 60 N F3 = 120 N Angle with respect to x-axis = 32 degrees Moment couple = 195 Nm
1 Use F1 = 12 kN is directed at theta = 45° and F2 = 10 kN. Using rectangular components, determine the magnitude and direction of the resultant force, measured counterclockwise from the positive x- axis. 5 KN 7 kN 30° 70°
Draw the shear and moment diagram using three moment equations. Assume the following support settlements: A= 1.00 in, B= 3.00 in, C= 1.50 in, D= 2.00 in Given that: E= 29x10⁶ psi and I= 3200 in⁴
(a) Find critical points (b) Calculate moment at these critical points (e) Draw a final moment diagram including dashed line (c) How many superposition sections (dashed line area)? Where is(are) superposition area(s)? (e.g., A-B or A-C, etc.) (d) Calculate moment value at B using superposition and show procedure including an equation in order to superimpose from the basic structures (f) Draw a shear diagram
A 30-m steel tape weighing 0.04 kg/m is constantly supported only at its end points, and used to measure a line with a steady pull of 8.5 kg. If the measured length of the line is 2465. 18 m, determine the correct length of the line. Please include the complete solution
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.