In Method 1 of the two-way switching for.3 :lighting, connections of switch 1 are (answer can be found in the 3rd & 4th minutes) common to the bulb, L2 to L1 of switch 2, & L1 to L2 of switch 2 line wire to L1, common to L2 of switch 2, & L2 to L1 of switch 2 line wire to common, L2 to L1 of switch 2, & L1 to L2 of switch 2 line wire to L2, L1 to L2 of switch 2, & common to L1 of switch 2 حدد إجابتك

In Method 1 of the two-way switching for.3 :lighting, connections of switch 1 are (answer can be found in the 3rd & 4th minutes) common to the bulb, L2 to L1 of switch 2, & L1 to L2 of switch 2 line wire to L1, common to L2 of switch 2, & L2 to L1 of switch 2 line wire to common, L2 to L1 of switch 2, & L1 to L2 of switch 2 line wire to L2, L1 to L2 of switch 2, & common to L1 of switch 2 حدد إجابتك

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter21: Special-purpose Outlets—food Waste Disposer, Dishwasher

Section21.2: Dishwasher Branch Circuit

Problem 1R

See similar textbooks

Similar questions

Explain each option & Choose the correct option. 4) The _ calculated load is rarely placed on an electrical system.A. optionalB. standardC. total 5) What's the primary disadvantage of using copper conductors?A. CostB. AvailabilityC. Weight 6) You're evaluating the components of a multioccupancy building that won't have an on-site employee. To be compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water pump disconnect ..
The connection method from the equipment grounding conductor to the box is carefully controlled. Three methods are provided: (1) a(n) , (2) equipment listed for grounding, and (3) a listed grounding device (e.g., ground clip). _____________
Exercise 2 (from chapter 6) For the diagram below, set up the following items; Kirchhoff loop for the bottom loop of the diagram. Kirchhoff loop for the top loop of the diagram. Kirchhoff loop for junctions A and B.
According to the Code, what trade size EMT is required for each of the following combinations of conductors? Assume that these are new installations. Show all calculations. Refer to Chapter 9, NEC, Table 4, Table 5, and Table 8. a. Three 14 AWG THHN, four 12 AWG THHN __________________ b. Two 12 AWG THHN, three 8 AWG THHN __________________ c. Three 3/0 AWG THHN, two 8 AWG THHN __________________
4.a. The ___ calculated load is rarely placed on an electrical system.A. optionalB. standardC. total 4.b. What's the primary disadvantage of using copper conductors?A. CostB. AvailabilityC. Weight 4.c. You're evaluating the components of a multioccupancy building that won't have an on-site employee. Tobe compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water-pump disconnect.
Nec article 210 q.#1 the rating of a branch circuit shall bedetermined by the rating of the?
1. You have a difficulty in opening the metal lid of your jam jar. What will you choose: a) dip it in a cold water b) dip it in a hot water? Why? 2. Why the wire that is connected in the posts outside are are lightly saggy not tightly tied by the line man? 3. What do you think is the reason why there are always a small gaps in the road even in a tiled floor?
20. A separately derived system is an electrical source, other than a service, having ____ connection(s) to circuit conductors of any other electrical source other than those established by grounding and bonding connections. Select one: A. INDIRECT B. NO DIRECT C. DIRECT D. COMPLETE
Which of the following products are not suitable for bonding on the supply side of the service disconnecting means? a) Threaded hubs b) Bonding bushings with jumpers c) Standard locknuts d) Threadless connectors made up tight
A DC is supplied through a solid conductor cable. The fault in the cable can be determined by using Murray Loop Test. The healthy cable has the insulation resistance of 1 kilo Ohms per meter. No fault occurred till the first 10 km. The core of healthy cable has the circumference of 7.86cm. If the resistivity of insulation is 900 G Ohm-mm, what is the diameter of the cable.
In the past, it was common practice to connect the lighting and receptacle(s) in a bathroom to the same circuit. Because of overloads caused by high-wattage grooming appliances, the Code now requires that these receptacle(s) be supplied by a separate 20-ampere branch circuit. Where in the Code is this requirement found? NEC __________
13.B. The amount of fault current that bonding connections have to endure is related to which of thefollowing?A. The quality of the fittings that were chosen for the systemB. The amount of available fault current delivered by the system or utilityC. The type of equipment and the location in the systemD. The number of connections that are part of the listed assembly13.C. What is the most common grounding electrode used to connect utility service equipment to Earth?A. Ground rodB. PipeC. PlateD. Ground ring