in Newton), and one couple. Determine the equivalent force-couple system with the force acting at point 0. • Resultant of all forces and its direction Resultant couple Consider PI - 100 + last digit of your student ID - Consider P2 - 50 + last digit of your student ID ree body diagram & direction of the Resultant are required

in Newton), and one couple. Determine the equivalent force-couple system with the force acting at point 0. • Resultant of all forces and its direction Resultant couple Consider PI - 100 + last digit of your student ID - Consider P2 - 50 + last digit of your student ID ree body diagram & direction of the Resultant are required

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bar with a right angle bend is supported by a collar A on smooth square rod, and by a roller at B. The forces and geometry are as shown in the figure and parameter table. Determine all the support reactions. Define all vector quantities to be positive in the positive coordinate axes directions. F₁ Az = Ay = B₂ parameter value 3 1.5 1.5 600 250 300 = F₂ (MA) T (MA)y= (MA) z C L₁ L2 L3 F₁ F₂ F3 B N N N units m ε|ε|ε|Ζ m m N N N N•m N•m N.m A cc 080 2021 Cathy Zupke
Problem 5.2 The rigid bar shown is pinned at A and supported by two steel rods, each having a diameter of 1 in. The system is subjected to a load P = 2 kip (note: kip refers to kilopound). If the bar is assumed to be rigid (meaning that it does not bend due to the loading) and is initially vertical, determine: A) The force in each bar when P is applied B) The displacement of end B when P is applied a = 1 ft, b= 1 ft D -b 2b B E AG Check your work: FEF = 1.26 kips a a a a P
a string of length L is stretched between points (0, 0) and (L, 0) on the x axis. At time t = 0 it has a shape given by f(x), 0 0 at2 The ends of the string are fixed at x = 0 and x = L, y(0, t) = y(L, t) = 0 t 2 0 The initial velocity of the string is zero, y(x,0) = 0 0 *>0 < x < L 0
The force F has a magnitude of 500 Ib and acts along the line AM where M is the midpoint of the vertical side OB of the parallelepiped. Express F as its magnitude times the appropriate unit vector and then determine its x-, y-, and z-scalar components. B 15" M F= 500 lb A 12" 17" Answers: Vector F = (500 Ib)(L Scalar components Fx = Ib Fy = Ib F = Ib
All the tension/compression members of the frame structure shown in the figure are pin-jointed and of equal length and negligible weight. An external load P = 27.3 kN is applied vertically at joint E. The frame is pin-connected at fixed support A and supported by a roller at D. What is the force in member BE? Input your answer as a value only in KN to one decimal place without +/- sign. B L A L L- E
Problem 2-16 Resolve the force Fzinto components acting along the u and v axes and detemine the magnitudes of the components. Given: F1 = 250 N F2 150 N e1 = 30 deg 82 = 30 deg 83 = 105 deg
4. Determine the three components of force (F3) the three concurrent forces as shown in the figure. F3=10KN 60° 45 F1=30KN 3 1 14 F2=50KN 60° 30° X
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 12 mm d = 100 mm t = 6.4 mm Additionally: • The area of each pipe is A = 1882 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 171660000 mm4. If the beam will be subjected to a shear force of V = 175 kN, determine the shear stress at point H, located at yH = 100 mm above the z centroidal axis.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 12 mm d = 100 mm t = 6.4 mm Additionally: • The area of each pipe is A = 1882 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz=171660000 mm4. If the beam will be subjected to a shear force of V = 120 kN, determine the shear stress at point H, located at yμ = 100 mm above the z centroidal axis. H Hv K Answer: TH= X MPa Ун Ук K Iv
Q3: Determine the resultant of the three concurrent forces shown in the Figure below. F = 10N F = 50N 60° F3 = 60N
• The three steel bars shown in the figure are pin connected to a rigid member. If the applied load on the member is 15 kN, determine the force developed in each bar. Bars AB and EF each have a cross- sectional area of 50 mm2, and bar CD has a cross-sectional area of 30 mm?. Take Est = 200 GPa. B D F 0.5 m E - 0.4 m- 0.2 m 0.2 m 15 kN
The following truss system is Pin Supported at Joint C and Roller Supported at Joint E. Joint B is subjected to a Point Load of 1000 Newton. Joint A is subjected to a Point Load of 1500 Newton. Show the values of Fat the beginning of the solution as well as the calculation steps and answer in the unit Newton. Using the Method of Joint, determine the forces in each member of the trusses shown in the following figure. 1500N 1000 N 12m 12m A В 8 m E 6 m D 12m 6 m Identify all the reaction forces at the supports.