In preparation of the earthworks of a proposed road, given below are the three-level cross section notes of stations 20 + 200 and 20 + 220. It is assumed that the ground slope is uniformly between sections with same side slope and width of base. Station 20 + 200 6.60 4.80 +2.4 + 2.0 +1.2 Station 20 + 220 6.30 7.20 +2.2 +2.8 What is the depth (m) of cut at station 20 + 220, if it has an area of 16.82 m2? O 1.38 O 1.27 O 1.49 O 156

In preparation of the earthworks of a proposed road, given below are the three-level cross section notes of stations 20 + 200 and 20 + 220. It is assumed that the ground slope is uniformly between sections with same side slope and width of base. Station 20 + 200 6.60 4.80 +2.4 + 2.0 +1.2 Station 20 + 220 6.30 7.20 +2.2 +2.8 What is the depth (m) of cut at station 20 + 220, if it has an area of 16.82 m2? O 1.38 O 1.27 O 1.49 O 156

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5. A square piece of land 60x60 m is to be leveled down to 6m above elevation zero. To determine the volume of earth be removed by the Borrow-Pit Method the land is divided into 9 squares whose corners are arranged as follows with the corresponding elevations, in meters, above elevation zero. Find the volume of cut in cu.m by u8nit area basis.A=29.8, B=27.3, C=25.2, D=28.3, E=26.5, F=24.3, G=26.9, H=23.3, I=24.2, J=21.3, K=22.6, L=20.5, M=21.1, N=18.5, O=17.8, P=20.5
Calculate the side widths and cross-section area of embankment having width =20m and side slope( 1/2 )formation level 20m.ground level=15m and ground slope ( 1/12) from C.L to side
Calculate the side widths and cross-section area of embankment having width =20m and side slope( 1/2 )formation level =20m . ground level=15m and ground slope ( 1/12) from C.L to side
Answer the subquestions: A. A slope measurement of 545.38 m is made between points A and B. The elevation of A is 424.25 m and that of B is 459.06 m. Determine the horizontal distance between two points. B. A traverse line was measured in three sections: 295.85 m at slope 8°45’, 149.58 m at 4°29’, and 373.48 m at slope 4°23’. Determine the horizontal length of the line. Note: Draw the figure and show the complete solution. Provide a recheck of the answers.
The areas in cut of two irregular sections 65 meters apart are 36m2 and 72m2 respectively. Base width is 10 meters, side slope of 3H:2V. Using prismoidal correction formula, find the corrected volume of cut in m3 between the two stations.
The areas is cut of 2 irregular sections 35m apart are 34 sq.mtrs and 56 sq.mtrs the base width is 10m. Find the volume of cutting using prismoidal rule having a side slope of 1 horizontal to that of 1 vertical. Discuss, how you derive your answer on the question above.
A rectangular concrete canal is to carry 0.182cms.The bottomwidth is trice the depth. What should be the dimensions of the stream cross-section if the slope is to be 0.001?n =0.014
Given a rectangular tract of land 690m by 1220m, the elevation at the center of the tract (E) is 165.0m and the elevation of corners A,B,C and D are 62.5m, 93.3m, 212.8m and 125.3m, respectively. Assuming uniformity of slope between the given corners, and contour interval of 20m, you are required to plot the contour lines. The contour lines with elevations of 100m and 200m to be shown as index contours.
A two-level section has the following data:bottom width=8m side ,slope=2:1 on the left ans 1:1 in the right,transverse slope of the ground=8:1.Find the area of the section if the height at the center is 35% of tge formation width
Define the term Slope Inclination Indicator.
A line was measured on a sloped ground to be 15.94 m long. If the vertical distance between the ends of the line is 0.78 m, what is the correction due to slope?
A traverse is a regular pentagon whose sides are 120 ft. The bearing of the first line AB is N 54° E. The elevations at each corner are A = 36ft, B = 28ft, C = 25ft, D = 33ft, E = 31ft, while at its center is 36ft. Assuming a uniform change in slope from corner to corner, and from the center to each corner, sketch the map and label “even” index contour lines at 2 ft-interval (i.e. 26ft, 28ft, 30ft, etc. Use an equivalence scale of 1 cm is to 20ft horizontal distance to plot the traverse.