in short Explain any two protective devices in the substation

Q: If you tested the system with a scan tool and you observed a diagnostic trouble codes DTC P0503 what…

A: The code P0503 means that the engine control mode has received a faulty signal voltage from the…

Q: Answer item number 1 only

A: Above question is based on DC network. In a DC network, the current flowing in the network is…

Q: The protective devices, such as ground wires, lightning arrestors, circuit breakers, relays are used…

A: Protection devices are installed with the aims of protection of assets and ensuring continued supply…

Q: Answer and write the solution. The substation bus bar is made up of 1.5 inches round copper bars 30…

A:

Q: 29: Suspension type insulators are used for voltages beyond

A: There are many type of insulators are available  strain type shackle type pin type suspension type

Q: The protective devices, such as ground wires, lightning arrestors, circuit breakers, relays are used…

A: The protective devices like relays, circuit breakers etc. are used to protect the equipment of power…

Q: power amplifier

A: a) Maximum Po(ac)        Vdc=VL(max)=30 VVdc=VpeakπVpeak=Vdc×π=30π=90.25…

Q: WHICH OF THE ELECTRICAL SWITCHES (USING JUST ONE UNIT ONLY) CAN YOU USE TO PUT ON AND OFF…

A:

Q: b) Material, which used to manufacture air conditioning pipes and air duct. c) Motor slip.

A: Polyurethane: This material is extremely strong and has excellent insulation properties. That is…

Q: e signals involved.

A: Delta Function- It is also known as the unit impulse function. It's value is equal to zero…

Q: Direction: List one (1)  safety precaution on electrical apparatus and one (1) safety precaution on…

A:

Q: True or False: In a 110 punch down block, each metal space joins two wires together then insert a…

A: Solution: 110 punch down is a tool used to install wiring from telephone,computer and various audio…

Q: What are the two factors that can disrupt the power supply

A: In this case, the two factors that can disrupt the power supply needs to be discussed.

Q: 2- Which quantity has been measured in order to measuring B?

A: we need to find Which quantity has been measured in order to measuring B.

Q: How do you do Kirchoffs Current law for this?

A: Given :    Let us consider the operational amplifier ideal hence it will offer infinite open loop…

Q: Questions A: 1. What happen if you only touch one test probe of the voltmeter to one end of a…

A: According to the question we have to discuss  1. What happens if you only touch one test probe of…

Q: Explain any 2 protective devices in the distribution system

A: The protective devices in distribution system consists of protective relays, fuses, lightening…

Q: Article 430 contains requirements for motor installations. The Section that requires a motor…

A: This is a multiple choice question about NEC (National Electrical Codes) which is a set of standards…

Q: fill the table with formula

A:

Q: Is there any iron lost in the short circuit test? If there is, why is it omitted

A: Yes, in short circuit test, iron losses or core losses are not absent (or zero) but they are…

Q: 17. Four electricians are discussing the size of boxes that must be installed to allow for the…

A: Here four electricians are discussing about the size of boxes that must be installed to allow for…

Q: Support the finding that workers face many electrical hazards on the job

A: Electrical Hazards on the job 1.Contact with live wire results in electric shock or burn 2.Exposed…

Q: Write the names of the given components and equipment in Table1. Table 1 2. 3. 4. 5. 6. 7. 8. 9. 10.…

A: Here the names are, 1. Speaker. 2.Solar panel

Q: Q1) Fill in the blanks by inserting appropriate words/numbers 1- The low value of k in voltage…

A:

Q: A copper bar has a length of (month) feet, width of (day) millimeters and thickness of (year)…

A:

Q: What are the type of circuit breaker

A: There are mainly four types of circuit breakers  1. Air blast Circuit Breaker  2. SF6 circuit…

Q: Explain the working of the electrical equipment used in the substation

A:

Q: Explain any 2 protective devices in the substation.

A: There are many protective devices which are used in the substation, this is done mainly to isolate…

Q: With the aid of diagram explain how Hot Water Geyser Control Circuit works.

A:

Q: Mention and explain 4 Electrical Hazards.

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: The operation of lamp-ballast circuit

A: Ballast are basically devices that controls the initial voltage and the operating current in a…

Q: How to put this on a breadboard without jumper

A: When the same current flows through all they resistors, they are said to be in series. In series…

Q: Explain from where ; 1) operation 2) circuit diagram 3) neat diagram 4) applicaiton note : pls…

A: Operation: The Generator is a device, which converts any kind of energy into electricity. The…

Q: Explain any 2 protective devices in the distribution system

A:

Q: A steel cable is used to hang an object. If you doubled the diameter of the cable for the same…

A: Stress: It is the ratio of force that is applied on an object and the cross-sectional area of the…

Q: Write the necessity of power supply and briefly describe different types of SMPS and UPS.

A: We use a lot of electronic devices in our homes, industries, and workplaces. These electronic…

Q: Mention 2 dangers on the wrong use of Appliances

A: Introduction: There are some danger electric hazards that could arise at any place like home,…

Q: Explain how the following Tests are undertaken; Insulation Test Earth Resistance Test iii.…

A: Insulation Test it is used to measure the total resistance between two pints which is separated by…

Q: Which of the following does not refer to electrical energy? Select the correct response: Joule…

A:

Q: Discuss the types of oil circuit breakers. Please write more answer

A:

Q: Which one of the following is the main function of the Anemometer in a Windenergy conversion system?…

A: The main function of the Anemometer in a wind energy conversion system

Q: . Part I of which article in the National Electrical Code provides general requirements for…

A: Correct option is ARTICLE 250

Q: Use the C-Strip material cards to fill in each blank with the correct abbreviation by first…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: 3- Assume you are a health safety environment engineer and you are working in an oil field. Explain…

A: Fire and explosion Because of the ignition of vapors or gases which is flammable people in the oil…

Q: What symbol or variable is used to represent the Electrical Admittance? A. B B. Y C. G D. Z

A: Electrical admittance is the reciprocal of electrical impedance. Electrical impedance is a vector…

Q: Year of birthday is 2001 so what would it be for part A, also help with part B!!

A:

Q: each tap conductor must be sized using which table in the NEC? a. 250.166 b. 250.102(C)(1) c. 250.66…

A: According to NEC, 250.166 is used for sizing of the grounding electrode conductor for a direct…

Frequency Modulation

Frequency modulation is a method or process of encoding the data of a specific signal (analog or digital) by modulating the carrier wave frequency according to the frequency of the modulated signal. Modulated signals are nothing more than information or data that should be conveyed after being converted into electronic signals.