In the circuit of Figure 1, let R = 0:125 Q, L= 10 mH, and the source voltage is e(t) = 151 sin(377t + a) V. Determine the current response after closing the switch for the following cases: (a) no dc offset; (b) maximum dc offset. Sketch the current waveform up to t = 0:10 s corresponding to case (a) and (b). Figure 1 Current in a series R-L circuit with ac voltage source R L V2V sin(wt + a) sw: = 0 elt) elt) ilt) + wt

In the circuit of Figure 1, let R = 0:125 Q, L= 10 mH, and the source voltage is e(t) = 151 sin(377t + a) V. Determine the current response after closing the switch for the following cases: (a) no dc offset; (b) maximum dc offset. Sketch the current waveform up to t = 0:10 s corresponding to case (a) and (b). Figure 1 Current in a series R-L circuit with ac voltage source R L V2V sin(wt + a) sw: = 0 elt) elt) ilt) + wt

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A series connection of a 30-ohm resistor and a 100-mH inductor is connected across 240-V, 60-Hz supply. What will be the resulting equation of the current? a. i(t) = 7.04 sin(377t + 51.49°) b. i(t) = 7.04 sin(377t - 51.49°) c. i(t) = 4.98 sin(377t - 51.49°) d. i(t) = 4.98 sin(377t + 51.49°)
In the circuit, C = 0.05 microFarad, V0 = 30 volt capacitor starting voltage and Io coil starting current = 0 amperes. In this case, the voltage response of the circuit; Since volts for t> 0 V(t)=-10e-5000t+40e-20000t , t = 0.0003. How many milliamperes per second iL (t) is the current iL (t). V(t)=-10e-5000t+40e-20000t
5.A RL circuit has no applied emf, a resistance of Rohms, an inductance of 2 henries, and an initial current of 10 amperes. Find the current in the circuit at any time t. Use R = 50
A resistor of R = 50Ω resistance is in series with a capacitor of C = 150μF. At t= 0, it is suddenly connected to a source of dc voltage of 25V. Determine the current in the circuit at any time t. Determine the current and the voltages across each element at t = 2τ.
A resistor of resistance 20 ohms is in series with an inductor of inductance 2H. At t = 0, it is suddenly connected to a dc source voltage of 50V. Determine the current in the circuit at any time t. Determine the current and the voltages across each element at t = 15ms.
In the circuit of the figure suppose that E = 9.00V, R = 15.0 ? and L = 0.060H. At t = 0, switch S1 is closed. Given data: The magnitude of resistance in the circuit is R=15 Ω. The magnitude of inductance in the circuit is L=0.06 H. The emf across circuit is E=9 V. A. i. What is the initial potential difference between points b and c just after switch S1 is closed? (Just give an answer) ii. Which point, b or c, is at higher potential or are they at the same potential (just after switch S1 is closed)? (Just give an answer). D. When the current has reached its final steady-state value, which point, b or c, is at higher potential or are they at the same potential? (Just give an answer).
In an AC circuit, resistance 50 Ω, inductance 0.3 H and capacitance 15 μF is connected to an AC voltage source 25 V, 50 Hz. Determine the inductive reactance in the circuit.
An AC circuit contains a 24-Ω resistor, a 15.9-mH inductor, and a 13.3-µF capacitor connected in parallel. The circuit is connected to a 240-V, 400-Hz power supply. Find the following values. P = I2 / R = VARsL = √VA squared - P squared = VARsC = VARsL(present) - VARsL(needed) =
The initial rate of current rise in an RL circuit is 300 amp per sec when 120 volts is suddenly impressed. What is the inductance of the circuit?
A 1-H inductor is connected in series with a 6-ohm resistor. If the connection is energized from a 9-V DC source, determine the current (in amperes) through the circuit for a long time. The initial current is 100 mA. Express your answers accurate to four decimal places. No need to put the units.
An R-L circuit takes a current 7A that lags behind the 231 V source by 35electrical degrees. Calculate the power factor, impedance, resistance, andinductive reactance of the circuit.
Please show your detailed solution Number 38 What value of inductance will draw a 160-mA rms current when connected to a 110-V 25-Hz source? A. 4.38 H C. 4.38 mH B. 687.5 H D. 110 mH