In the circuit shown, assume that the op-amp is ideal. If the gain (vo/vin) is -12, the value of R (in k Ohms) is Input the whole number only. Show solution on your answer sheet. 10 k2 10 kQ 10 kQ Vin VO

In the circuit shown, assume that the op-amp is ideal. If the gain (vo/vin) is -12, the value of R (in k Ohms) is Input the whole number only. Show solution on your answer sheet. 10 k2 10 kQ 10 kQ Vin VO

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Related questions

Q: 6. c. Sketch the configuration of the measurement system. d. Classify the types of operational…

A: Measurement system is define as a system which is fabricated to measure any quantity or any physical…

Q: For the circuit illustrated in Figure Q3, determine the state space representation Ax + Bu and y =…

Q: hat is the impulse response of a stable discrete-time system with the following mathematical…

Q: Wr R-12 kO 10 v c100 V

Q: Consider the sequences n+) +3 sin (n -) vin] = cos (품7). and = COS x[n] = v2 cos Is it possible to…

A: From the eigen value property of Fourier transform we know that:-

Q: 15 Which of the following circuits requires greatest number of transistors? O single-phase…

A: Single phase full bridge inverter uses 4 transistors. Single phase half bridge inverter uses 2…

Q: A 12 KVA, 440/220 V, 50 Hz single phase transformer has 275 secondary turns. he no load current of…

Q: Determine and sketch the Vo for each of the network shown.

A: Brief description: In the above given circuit they need to know the value of output voltage…

Q: Ql) Fill in the blanks: 1- The acronym VHDL stands for 2- FPGA consists of a matrix of…

A: VHDL stands for very high speed integrated circuit(VHSIC) Hardware Description language.

Q: The Beta of a certain BJT is known to be approximately 172. How much base current (in microamperes)…

Q: - the transistor circuit shown below, what is the value of the emitter current? Vcc = +16 V Ic Rc…

Q: Boit-Savart Law 7/21 • Exercise: Consider eircular filamentary wire located at the z 0, with a…

A: It is given that: Circular filamentary wire located at z=0Constant current=I

Q: Twenty-four voice signals are to be transmitted via multiplexed PAM with a marker pulse for frame…

Q: Two 3-phase, 6.6 kV, star-connected alternators supply a load of 3000 kW at .f. lagging. The…

Q: Q2\ Find the Thévenin circuit for the portions of the networks in Figure below external to the…

Q: transfer function

A: Given: Consider the following circuit: To find: Transfer function

Q: 2) A 240 Volt 60cycle source is connected to a coil of wire that has a resistance of 750 and an…

Q: A DC Circuit V When Is = 5 A, then the voltmeter reads 1 V and when Is = 7 A, then the voltmeter…

A: Using thevenin theorem, we can convert the DC network across the load terminal into thevenin circuit…

Q: or the transistor circuit shown below, what is the value of the collector current? Vcc = +20 V Rc…

Q: Q3. a) Angle modulation is categorised as either Frequency Modulation (FM) or Phase Modulation (PM)…

Q: In the circuit shown in Fig. 2.87, determine v, and the power absorbed by the 12-N resistor. 12 1.2…

Q: Q) An op amp has a GBP of 10°. If a signal of 10 mV at 10 KHz is required to be amplified to 12 V.…

A: Given,The gain bandwidth product is,GBP=106The input signal is,Vin=10mVThe amplified output signal…

Q: For the given state diagram, design and implement the circuit using T Flip-Flops and necessary…

Q: 2.43 Find VA and V, in the circuit in Fig. P2.43.

Q: Sometimes we can account HV Under Ground Cable (HVUGC) as a power factor improvement because of:…

A: The power factor gets improved with the length of the cable.

Q: Given the following h1(n) = {2, 2, 1} h2(n) = (5) u(n) - (*) sin (n) u(n) h3(n) = 3 Determine the…

A: According to the question, we need to find the system function H(z).

Q: = Find the Integration

Q: A Wheatstone bridge requires a change of 212 in the unknown arm of the bridge to produce a change in…

A: Given, Change in deflection of 9 mm of the galvanometer, Resistance change in unknown arm is 21 ohm.

Q: i need the answer quickly

A: Here grammatical Q. is discussed.

Q: Ohm is the unit of resistance and it is a unit. ........ Derivative basic complex

Q: Suppose you have a three-phase generator that provides 120 Vac per phase and works at a frequency of…

A: In delta connection line voltage is equal to phase voltage.

Q: please tell me last part answer

A: let Z = a+jb then a is called real part and b is called imaginary part .

Q: E3.19 Use mesh analysis to find V, in the circuit in Fig. E3.19. 12 V 2 kl 20001,+ 4 kf? 2 kn Figure…

A: We need to find voltage for given circuit

Q: c) Why diodes should be connected in antiparallel with the transistors in inductive circuits? d) A…

A: Diode is uncontrolled Device in which their ON and OFF state is controlled by external circuit…

Q: In the circuit of Fig. 2.75, calculate Vị and V2. 1 V 2 V + + + + V1 5 V V2 V1 = V V2 = V

Q: power of 750 W. How much power is added to the signal when the transmitter is 100 percent

Q: For circuit below if propagation Delay of each gate is 20 nsec, Octermine out put duration. A Timing…

Q: For the circuit below, use nodal analysis with impedance and/or admittance opera- tors to find the…

A: Solution

Q: What is the BJT DC Analysis?

A: DC Analysis of a Bipolar Junction Transistor Circuit Using Thevenin's theorem and Kirchhoff's…

Q: If Ibc is equal to 353.338∠146 and Ia is 204∠56, Ica should be…

Q: An independent and constant current source is supplying 0.6 ampere to a uniform copper conductor…

A: Given: An independent and constant current source is supplying 0.6 amperes to a uniform copper…

Q: For the voltage-divider configuration of the figure below: a) Sketch the DC equivalent circuit b)…

A: Brief description: In the above given question they have mentioned a common source amplifier…

Q: In the circuit of Fig. 2.76, obtain v1, V2, and v3. 15 V 25 V 10 V + V2 - + v2 20 V v1 = V V2 = V3 =…

A: To find voltages v1 , v2 and v3 in the given circuit

Q: 29 The zener diode current is: * R1 = 5002 15 V 12 13 R2= 15002 AVz = 10 V O 667 mA 5 mA O 333 mA 10…

A: We need to find out zener diode current for given circuit

Q: The shown equivalent circuit is valid for BJT PNP MOSFET MOSFET IGBT Bipolar transistor Diode

Q: In the circuit shown below , find the following: (a) total resistance, (b) current through each…

A: We need to find out current, voltage and power for given circuit

Q: 0.4mH 1N 12 V2 Vi W We are determining the Thevenin equivalent of the circuit as seen by Ra. The Vth…

A: Given data Vth=13.65 at angle of 28.95

Q: Consider the following circuit. Find the values of the voltages V.V and v, Find the currents in the…

Q: Q) An inductive proximity sensor is used to detect the presence of car in traffic lights. The output…

A: Given data, input frequency(fi)=30kHzAllowable variation in frequencies,=10kHz=∆f

Q: 6. Determine the total energy consumption and cost of using the following appliances if the rate is…

A: In this question we need to find the total energy consumption and cost of the given appliances

Concept explainers

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.

Question

In the circuit shown, assume that the op-amp is ideal. If the gain (vo/vin) is -12, the
value of R (in k Ohms) is
Input the whole number only. Show solution on your answer sheet.
10 k2
10 kQ
R
10 k2
Vin
Vo

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The op amp in the adder-subtractor circuit attached is ideal. A. Find the output voltage v0 given Va = 2V, Vb = 3V, Vc = 5v, Vd = 6V. B. For the values given in A, find V0 if the feedback resistor is replaced with a 100 ohm resistor.
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem. c. If L = 1H, sketch the straight-line approximation of the Bode plot for the circuit’s gain assuming the op amp can still be considered as ideal.d. The op amp you select turns out to be non-ideal, and it has a real pole at wC = 1krad/s. Write the updated transfer function for your circuit (using your values of R1, R2, and L = 1H). Make it in the canonical form.e. Sketch the straight-line approximation of the Bode plot for the circuit with your updated transfer function from D.
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem.
Please show that gain = -(1-n)/(1+nA) , n = R1/(R1+R2) and compare to gain of ideal op amp. Calculate the input and output impedances, and lastly whats the point of the resistor R1//R2 on the non-inverting input? What would be the best value for this resistor? (pretending it wasn't given that the value is R1/R2).
Using the components listed below, design an amplifier having a voltage gain of −10 ± 20 percent. The input impedance is required to be as large as possible (ideally, an open circuit). Remember to use practical resistance values. Cascade a non-inverting stage with an inverting stage.1) Standard 5%-tolerance resistors.2) Standard 1%-tolerance resistors. (Don’t use these if a 5%-tolerance resistor will do, because 1%-tolerance resistors are more expensive.)3) Ideal op-amps.4) Adjustable resistors (trimmers) having maximum values ranging from 100 Ω to 1 MΩ in a 1–2–5 sequence (i.e., 100Ω, 200Ω, 500Ω, 1 kΩ, etc.). Don’t use trimmers if fixed resistors will suffice.
For the op-amp circuit shown below, find the value of vO, where R1 = 19 Ω, R2 = 14 Ω, R3 = 18 Ω, R4 = 14 Ω, Rf = 11 Ω, VS1 = 15 V, and VS2 = 3 V.
Consider the active circuit:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw) in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem.
Consider the following op amp configuration.(a) Choose R2 such that the ideal voltage gain is Av = 40dB and draw the amplifier’stransfer characteristic.(b) Find the amplifier’s input and output resistances.(c) If the op amp’s internal gain is Ao = 120dB, what is the expected voltage gain ofthe entire network?
Assume the op amps as shown are ideal except for power supply voltages of ±12 V. (a) If the input voltage is 5 mV, what are the voltages at the8 nodes in the circuit? (b) Repeat for an input voltage of 10 mV. (c) Repeat for an input voltage of 10 mV with an open-loop gain of 80 dB.
Assume the op amp is ideal. Find the expression for Vo in terms of VA, VB and theresistances.
The inverting amplifier in the circuit shown has an input resistance of 500 kΩ, an output resistance of 5 kΩ, and an open-loop gain of 300,000. Assume that the amplifier is operating in its linear region. 1. Calculate the voltage gain (vo/vg) of the amplifier. 2. Calculate the value of vn in microvolts when vg=1 V. 3. Calculate the resistance seen by the signal source (vg). 4. Repeat (a)–(c) using the ideal model for the op amp.
The above cascade circuit uses ideal op-amps. Assume the following: in the second picture Find A of vo1(t) in units of [V ]. Find B of vo1(t) in units of [V ]. Find F of vo2(t) in units of [V ]. Find G of vo2(t) in units of [V ]. Thank you!