In the circuit shown below, let Imax be the maximurm lo current in the circuit, and Imin be theminimum l, in the circuit. Let the total resistance of the potentiometer = 20KO. Then, thevalue of the resistance R, such the ratio Ima/lmin equals to 10 isReDMM10vPoA. SkOB.0.55kOC125k(2D. 2.22kONext pageThe maximum and minimum values of Is are 0.5 and 0.1 A. This indicates that the value of the rheostat resistance R is:40 S2IsVs=RO a. 280 0b. 350 0C. 160 0Od. 240 0

To find the value of Ro The maximum current flows in the circuit when slider is at 0 ohm position…

In the circuit shown below, let Imax be the maximurm lo current in the circuit, and Imin be the minimum l, in the circuit. Let the total resistance of the potentiometer = 20k). Then, the value of the resistance Ro such the ratio Ima/lmin equals to 10 is DMM Vs Po A Sk) B. 0.55k2 C125kt2 D. 2.22k Next page The maximum and minimum values of Is are 0.5 and 0.1 A. This indicates that the value of the rheostat resistance R is: 40 $2 Is Vs O a. 280 0 O b. 350 n OC. 160 0 Od. 240 0

In the circuit shown below, let Imax be the maximurm lo current in the circuit, and Imin be the minimum l, in the circuit. Let the total resistance of the potentiometer = 20k). Then, the value of the resistance Ro such the ratio Ima/lmin equals to 10 is DMM Vs Po A Sk) B. 0.55k2 C125kt2 D. 2.22k Next page The maximum and minimum values of Is are 0.5 and 0.1 A. This indicates that the value of the rheostat resistance R is: 40 $2 Is Vs O a. 280 0 O b. 350 n OC. 160 0 Od. 240 0

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 11PP: In an R-L parallel circuit, ET=208 volts, R=2.4k, and XL=1.8k. Find IT.

See similar textbooks

Similar questions

Virtual Lab: circuits and Kirchoff’s rules Go to: https://phet.colorado.edu/it/simulation/circuit-construction-kit-dc-virtual-labBuild each of the circuits in the figures, with the designed characteristics.For each of the circuits, show the calculations to find the current and the potential difference in eachelement of the circuit.In building the circuit in Figure 1) through the simulator, adjust the small resistance of the battery tozero and put in series a small resistance as required from the design.For instance, for E1 you will need abattery with V = 6V and you will need to put in series a small resistance of 0.5 Ω to simulate the smallresistance in a battery.Figure 1)Figure 2)
Using the following values for the circuit in the figure, find what is required in the questions? For the circuit in the figure, find the ones requested in the questions by using the following values? VDD= 30 V, IDSS=8 mA, VP=-6V, R1=110 MΩ, R2=18 MΩ RD=1.9 kΩ, RS=9.12 kΩ VD=? VS=? VDS=?
Using the following values for the circuit in the figure, find what is required in the questions? For the circuit in the figure, find the ones requested in the questions by using the following values? VDD= 30 V, IDSS=8 mA, VP=-6V, R1=110 MΩ, R2=18 MΩ RD=1.9 kΩ, RS=9.12 kΩ VG=? VGS=? ID=? VD=? VS=? VDS=?
Help me answer, I want to check my solution To get the contribution of the 75V source to iR, we first kill the 50mA source. What is the resulting equivalent resistance in series with the 75K resistor (in Kohms) To get the contribution of the 75V source to iR, we first kill the 50mA source. What is the resulting value of iR (in mA)? What is the nodal equation for Vx? What is the Thevanin voltage in (Volts) and Thevanin resistance in (Kohms)?
Using the diagram, solve for the Rth, Vth, and load current (IL) through each resistance using Thevenin’s Theorem. Please draw the circuit diagram for each Rth and Vth computation.
Using the following values for the circuit in the figure, find what is required in the questions? For the circuit in the figure, find the ones requested in the questions by using the following values? VDD= 30 V, IDSS=8 mA, VP=-6V, R1=110 MΩ, R2=18 MΩ RD=1.9 kΩ, RS=9.12 kΩ VG=? VGS=? ID=?
If we connect n 1000-Ω resistances in parallel, what value is the equivalent resistance?
How about the Norton Resistance (RN) of the circuit?
Need help with this Question The D-MOSFET circuit shown in Figure Q1(b) has IDSS = 3 mA and VGS(off) =−8 V. Given the following:R1 = 50 kΩR2 = 150 kΩRD = 1 kΩRS = 2 kΩVDD = +10 VVSS = −10 VDetermine VGS, ID and VDS.
following equation applies: V = IR. Outside of the linear range, V*IR, outside of the linear ranges where resistors are broken The resistor has a resistance of 100ohm, and a power rating of 250mW. 1) Sketch the plot (and label) of the i-v relationship for the resistor using only the linear range of the resistor. Determine the range of values for the voltage and current that the resistor operates as a linear element and note these simplified numerical values on the plot.
For the circuit in the figure, find the ones requested in the questions by using the following values? VT=2,91 V, ID(on)=6,13 mA, VGS(on)=6,9 V VG=? VGS Q =? ID Q =? VDS=?
For the given circuit in Figure below, find the open circuit voltage VTH and the short circuit current IN across the terminal. then, find R TH by using the RTH=VTH/IN equation and find RTH with replacing voltage source with short circuit. Let’s assume we connect RL (load resistance) to the circuit between points A and B, what should be the value of RL in order to have max power transfer.