In the continuous regime, there is a constant heat generation of q = 3x107 W/m³ in a one-dimensional wall with a thickness of 20 mm. The heat conduction coefficient of the wall material is k = 32 W / mK. The temperature Ts on the wall surface is T,1= 127 ° C and Ts on the other surface is Ts,2= 27 ° C. So, find where the highest temperature occurs in the wall?

In the continuous regime, there is a constant heat generation of q = 3x107 W/m³ in a one-dimensional wall with a thickness of 20 mm. The heat conduction coefficient of the wall material is k = 32 W / mK. The temperature Ts on the wall surface is T,1= 127 ° C and Ts on the other surface is Ts,2= 27 ° C. So, find where the highest temperature occurs in the wall?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.17P: 3.17 A 1.4-kg aluminum household iron has a 500-W heating element. The surface area is . The ambient...

See similar textbooks

Similar questions

2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
2.29 In a cylindrical fuel rod of a nuclear reactor, heat is generated internally according to the equation where = local rate of heat generation per unit volume at r = outside radius = rate of heat generation per unit volume at the centerline Calculate the temperature drop from the centerline to the surface for a 2.5-cm-diameter rod having a thermal conductivity of if the rate of heat removal from its surface is 1.6 .
Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
2.9 In a large chemical factory, hot gases at 2273 K are cooled by a liquid at 373 K with gas-side and liquid-side convection heat transfer coefficients of 50 and , respectively. The wall that separates the gas and liquid streams is composed of a 2-cm thick oxide layer on the gas side and a 4-cm thick slab of stainless steel on the liquid side. There is a contact resistance between the oxide layer and the steel of . Determine the rate of heat loss from hot gases through the composite wall to the liquid.
Estimate the rate of heat loss per unit length from a 5-cm ID, 6-cm OD steel pipe covered with high-temperature insulation having a thermal conductivity of 0.11 W/(m K) and a thickness of 1.2 cm. Steam flows in the pipe. It has a quality of 99% and is at 150C. The unit thermal resistance at the inner wall is 0.0026(m2K)/W the heat transfer coefficient at the outer surface is 17W/(m2K) and the ambient temperature is 16C.
1.37 Mild steel nails were driven through a solid wood wall consisting of two layers, each 2.5-cm thick, for reinforcement. If the total cross-sectional area of the nails is 0.5% of the wall area, determine the unit thermal conductance of the composite wall and the percent of the total heat flow that passes through the nails when the temperature difference across the wall is 25°C. Neglect contact resistance between the wood layers.
3.17 A 1.4-kg aluminum household iron has a 500-W heating element. The surface area is . The ambient temperature is 21°C, and the surface heat transfer coefficient is . How long after the iron is plugged in does its temperature reach 104°C?
Heat is transferred at a rate of 0.1 kW through glass wool insulation (density=100kg/m3) with a 5-cm thickness and 2-m2 area. If the hot surface is at 70C, determine the temperature of the cooler surface.
On a multi-layered square wall, the thermal resistance of the first layer is 0.005 ° C / W, the resistance of the second layer is 0.2 ° C / W, and the third layer is 0.1 ° C / W. The overall temperature gradient in the wall is multilayered from one side. to the other side is 70 ° C. a. Determine the heat flux through the walls. = Answerwatts / m2. b. If the thermal resistance of the second layer is changed to 0.4 ° C / W, what is the effect in% on heat flux, assuming the temperature gradient remains the same? = AnswerAnswer%.
the plane Wall seen in the figure is L=20 cm and the heat conduction coefficient is 57 W/mK. Inside the wall there is a uniform distributed volumetric heat generation of 120 kW/m3. One surface of the wall is a fluid alloy with a temperature of 15 Co, the otherits surface is subjected to heat flux of Q0 = 50 kW/m2. Since the heat transfer coefficient between the wall and the fluid is 400 W / m2 K, accepting the temperature change within the wall as one-dimensional and continuous,a) draw the temperature change curve by finding the correlation that gives the temperature distribution inside the Wall b) find the maximum temperature inside the Wall? E) find in x=L?
the composite wall of a refrigerator has a thermal conductivity of 0.05 W/m-K and a wall thickness of 50 mm. In a room of 25 °C, the refrigerated cold space inside the refrigerator is maintained at 4 °C. Assume the inner and outer convection heat transfer coefficients are 5 W/m² K and 10 W/m².K, respectively. Neglect radiation heat transfer. Determine the rate of heat leaking into the refrigerator per unit surface area.