In the Fig. is shown the cross-section of the tank full of water under pressure. The length of the tank is 3 m. An empty cylinder lies along the length of the tank on one of its corners as shown. Find the horizontal and vertical components of the force acting on the curved surface LMN of the cylinder. * 35kN/m 1.2 m Tank full of liquid s=0.85 Empty cylinder Your answer -2 m

In the Fig. is shown the cross-section of the tank full of water under pressure. The length of the tank is 3 m. An empty cylinder lies along the length of the tank on one of its corners as shown. Find the horizontal and vertical components of the force acting on the curved surface LMN of the cylinder. * 35kN/m 1.2 m Tank full of liquid s=0.85 Empty cylinder Your answer -2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

DETERMINE THE PROPER POSITION OF THE C- PURLIN IF THE LOAD IS SUBJECTED DOWNWARD. (B) 10 mm 100 0mm 0mm DETERMINE THE MOMENT OF INERTIA WITH RESPECT TO ITS CENTROIDAL X - AXIS (Uit: mm^4) Your answer DETERMINE THE MOMENT OF INERTIA WITH RESPECT TO ITS CENTROIDAL Y - AXIS (Unit: mm^4) Your answer
Draw the FDBS of member ADB and BEC 1 m 1 m В C E 1 m D 1.6 m
The bracket shown below consist of two plates riveted to a column by 4-20 mm Ø rivets which is subjected to an eccentric load of 150 kN. 1. Which of the following gives the shearing stress due to axial load only a. 29.84 MPa b. 42.20 MPa c. 49.32 MPa d. 66.72 MPa 2. Which of the following gives the shearing stress due to axial load only? a. 29.84 MPa b. 42.20 MPa c. 49.32 MPa d. 66.72 MPa 3. Which of the following gives the value of the maximum shearing stress in the rivets? a. 29.84 MPa b. 42.20 MPa c. 49.32 MPa d. 66.72 MPa
1- For the beam shown in the figure below: aReplace the loading system with an equivalent resultant force and couple moment at point A. b) Replace the loading system with an equivalent resultant force and couple moment at point B. 650 N 30° 1500 Nm TH 300 N -3 m- -5 m- 500 N 60 -2 m
L+I 7 (ab)" a-bm f 2 1 TY –314 - 2- 6 STATICS ENGINEERS MECHANICS CHAPTER Lecture Notes: = m %3D EXAMPLE: 22 einber 6O 3.45 m 1.25 m + 3 Pz 1.85 m 1 1.22 m Wa120 IN A weight W• 120 kM is being supported by steel sections with force T. force and force C. The coordinates of A. B. C. and D are given. Assume that E is the origin (0.0.0). Determine Forces T. F, and C.
water 3cm D=5 cm Mereury The tank in the has a 5 cm diameter plug at the bottom.on the rrght. All fluids are at zóc The Plag will pup out if the hydrestatic force is 30 for this condition what will be the readineg h ont Meicury mahometer on the left side2
DETERMINE THE PROPER POSITION OF THE C-PURLIN IF THE LOAD IS SUBJECTED DOWNWARD. 1. DETERMINE THE MOMENT OF INERTIA WITH RESPECT TO ITS CENTROIDAL X-AXIS (Uit: mm^4) 2. DETERMINE THE MOMENT OF INERTIA WITH RESPECT TO ITS CENTROIDAL Y-AXIS (Unit: mm^4) 3. PROPER POSITION OF THE PURLIN (A or B) (A) (B) 10 mm I80 mm 100 mm 10 mm 10 mm 100 ma 10 mm 180 mm 001
Y:1E O ZVA N O 令 hw#3.docx -> If the resultant force acting on the bracket is to be Determine the magnitude and direction of the nesutant fone 750 N directed along the positive a axis, determine the magnitude of Fand its direction 6. Determine the magnitude of the resultant force acting on the plate and its direction, measured counter dlockwise from the positive r atis If the magnitude of the resaltant force acting on the bracket is to be 80 Ib directed along the u axis, determine the magnitude of Fand its direction e. If F-30 lb and F;-40 Ib, deteramine the angles ana o so that the positive atis and han a magnitude of F-60 h e resultant force is directed along the Determine the magnitude of the resultant force and its direction, measured counterclockwise from the positive x axis. F-8AN 5-SAN 45 = 4 kN
Q2: Reduce the system of forces and moment shown to (a) an equivalent two * forces and couple system at A 5 KN 0.5 m 2 m 75° To.15 m 10.15 m 500 N-m ---x 1.2 kN
The bracket BCD is hinged at € and attached to a control cable | ! at B. For the loading shown, determine (a) the tension in the cable, (b) the reaction at C. a=0. 18m 20N 20N 8 c o I_.l_nm—l—um—-l 02¢m
Calculate the magnitude and nature of forces in members marked 1, 2, 3 and 4. Assume all member to be pinjointed. ion: ] H C J 4 2 D K E L F 30 t 15t 30 t -6 panels @ 4 m = 24 m- M G Solved Papers T 3m4m BIL
Problem 14 , 3 parts ....plz solve all parts I vll upvote