In the figure below, a fluid with a specific gravity of 0.77 is flowing. The mass flow rate is recorder to be 18.5 kg/s and the pressure gage at point 1 is 175 kPag. Point 2 is right after the nozzle. The diameter of the nozzle is 4.87 cm. Note that the angle shown is 35 degrees. Determine the velocity at point 2 in m/s p = 175 kPag

In the figure below, a fluid with a specific gravity of 0.77 is flowing. The mass flow rate is recorder to be 18.5 kg/s and the pressure gage at point 1 is 175 kPag. Point 2 is right after the nozzle. The diameter of the nozzle is 4.87 cm. Note that the angle shown is 35 degrees. Determine the velocity at point 2 in m/s p = 175 kPag

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter9: Mass And Mass-related Variables In Engineering

Section: Chapter Questions

Problem 37P

See similar textbooks

Similar questions

In figure 3 compute the pressure head difference between m and n, in feet of fluid A, when: A. Fluid A is gasoline (sp gr 0.715), the gage liquid is mercury, and z = 47.77 in B. Fluid A is oil (sp gr 0.908), the gage liquid is water, and z = 27.77 in C. Fluid A is sea water (w = 64.0), the gage liquid has a specific gravity of 2.95, and z = 57.77
Consider a hydraulic jack being used in a car repair shop, as in the figure. The pistons have an area of Ap= 0,8 cm? and A= 0.04 m2, Hydraulic oil with a specific gravity of 0.870 is pumped in as the small piston on the left side is pushed up and down, slowly raising the larger piston on the right side. A car that weighs 13,000 N is to be jacked up. At the beginning, when both pistons are at the same elevation (h= 0), calculate the force F+ in newtons required to hold the weight of the car. 1. What height of mercury column will cause a pressure of 680 kPa? Use sg of mercury equals to 13.6 2. Determine the pressure in a vessel of mercury, specific gravity 13.6, at a point 20 cm below the surface. Express the answer in kN/m2.
Consider a fully filled tank of semi-circular cross section tank with radius R and width of b into the page, as shown. If the water is pumped out of the tank at flow rate of V· = Kh2, where K is a positive constant and h is the water depth at time t. Determine the time needed to drop the water level to a specified h value of ho in terms of R, K, and ho.
A block in the following figure is pulled up with a Force 20 +S Nt. The weight of the block is 10 Nt. The area of the contact surface between the block and fluid is 10 cm2. a)find the velocity of the block if the fluid is an ideal fluid b)find the velocity of the block if dynamic viscosity of the Fluid between the block and inclined surface in the figure is 0.2 Nt.s/m2. (S=4)
The figure shows gate AB, 4 meters high, submerged in water. It is inclined 40 degrees with respect to the horizontal. Using the figure shown, determine the distance of CG (center of gravity) to CP (center of pressure) in meters.
In figure 6, compute the pressure difference between m and n, in pounds per square inch, when: A. Fluid A is brine (sp gr 1.15), the gage fluid is oil (sp gr 0.92), and z = 47.77 in. B. Fluid A is water, the gage fluid is air, and z = 17.77 in.
The differential manometer shown in figure 4 is used to measure pressure difference between pipe A and B. Pipe A is conveying water while pipe B is conveying air. If the pressure at B is 12kPa calculate the pressure at A. Figure 4. (a) 35kPa (b) 12kPa (c) 23kPa (d) 24kPa
Water enters a large rigid tank steadily at a rate of V . = 0.5 m3/s, and exits through a large rectangular opening through which the velocity changes linearly in the vertical direction from 4 m/s to 5 m/s. Knowing that the tank is full, determine the magnitude of the velocity through the circular opening at the top whose diameter is D = 15 cm.
Fluid mechanics- Bernoulli's Equation along a streamline: The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure tap at station 1. The velocity at station 2 is twice that at station 1. Air with a density of 1.2kg/m3 flow through the duct. A water manometer is connected between the stagnation probe and the pressure tap, and a deflection of 10cm is measured. What is the velocity at station 2?
5. The system shown on the right is used to accurately measure the pressure changes when the pressure is increased by ∆? in the water pipe. When ∆ℎ=70??, what is the change in the pipe pressure (kPa)? (3 decimal)
fluıd mechanıcs If an oil tank is pulled uphill on a surface that makes an angle of 162 with the horizontal, the oil makes an angle of 160,a) Show the forces acting on the tank on the figure. Write the balance of force.b) Calculate the constant acceleration of the tank being pulled uphill.
The water flow rate in the pipe will be measured using the pitot tube system given in the figure. At point 1, the velocity is zero and represents the stationary point. Since there is mercury with a density of 13600 kg/m3 in the manometer and the height of the manometer is read 0.06, calculate the volumetric flow rate of the water flowing in the pipe with a diameter of 0.2 m. (ρwater = 1000 kg/m3)