In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. P P 1.95in -bb P P 6.25in Determine the dimension b so that the joint is as strong as the boards. inches in 2 decimal places

In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. P P 1.95in -bb P P 6.25in Determine the dimension b so that the joint is as strong as the boards. inches in 2 decimal places

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. Determine the dimension b so that the joint is as strong as the boards.____________inches in 2 decimal places.
A joint is made by gluing two plywood gussets of thickness t = 0.56 in to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 12.65 in and the applied force is P = 7475 lb. Round off the final answer to three decimal places.
A steel has a modulus of elasticity of 200GPa and a Poisson’s of 0.4. Compute the shear modulus of steel. a. 73,265.55 MPab. 71,428.57 MPac. 96,354.54 MPad. 81,234,45 MPa
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 6 (Example: 4QT mm2 = 406 mm2). Just substitute the number in letter. Thank you! A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 4QT mm2. Determine the average axial stress in each bar.
Estimate the shear strain yxy at point D with respect to the xx and yy directions. A rectangle ABCD has width 400 mm (in the x-direction) and height 300 mm (in the y-direction). It deforms into the shape in the dashed lines. Point A (lowe right corner) moves to the right by 3 mm and upward by 2 mm, point B (upper right corner) moves to the right by 5 mm and upward by 4 mm, point C (upper left corner) moves to the right by 2 mm and upward by 2 mm.
Two boards are joined by gluing along a scarf joint, as shown in the figure. For purposes of cutting and gluing, the angle a between the plane ofthe joint and the faces of the boards must be between 10° and 40°. Under a tensile load P, the normal stress in the boards is 4.9 MPa.(a) What are the normal and shear stresses acting on the glued joint if α = 20°?(b) If the allowable shear stress on the joint is 2.25 MPa, what is the largest permissible value of the angle a?(c) For what angle a will the shear stress on the glued joint be numerically equal to twice the normal stress on the joint?
Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.94 in2, A2 = 0.38 in2, P1 = 81 kips, P2 = 49 kips, P3 = 31 kips and E = 29x106 psi Your final answer should have three decimal places
Text:A beam is made using the HE240A profile. The beam is 7 meters long and secured against displacement at node A and restrained against displacement in the vertical direction at node B, which indicated on the sketch. The beam is supported by a uniformly distributed load q= 6,40 kN/m between junction point A and B. and concentrated downward load P. Modulus of elasticity for steel is 2,0x105N/mm2. Cross-sectional data is obtained from steel table. A)Calculate how large the force can be when the transverse displacement (see image)apply superposition principle Calculate how large the transverse displacement (see image), , under the concentrated load will be for this the load effect. When the transverse displacement u(x) for a freely supported beam with uniform distributed load is: SEE IMAGE
The cross section of a continuous one way slab in a building is shown in the figure. The slabs are supported by means of beams that span 3.6 m between simple supports. The dead load on the slab is 3 kPa (besides its own weight) and a live load of 7 kPa. =21 MPa, =276 MPa. Use 20 mm clear cover. Unit weight of concrete = 24 kN/m3.a) Determine the thickness of slabb) Determine the spacing of 16 mm bars at section CDc) Determine the spacing of 16 mm bars at section E.
Two strips of plastic material are bonded together using splice plates as shown. The average shearing stress in the glue must be limited to 1,050 kPa. If P = 45 kN, what splice plate length L is required? a. 142.9 mm b. 149.2 mm c. 192.4 mm d. 124.9 mm
The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the wood makes a 30.3º angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 20.2 MPa. Round off the final answer to four decimal places.
An alloy steel having a diameter of 0.45 in. extends 0.002 in. over a gage length of 2.2 in. due to a tensile load of 3900 lb. What is the modulus of elasticity of this alloy steel? A)29,010 ksi B)27,000 ksi C)30,000 ksi D)28,000 ksi