In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm². The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. D 1.7m 1.7m x-P B 3.5m7 Find the magnitude P of the largest additional vertical force that can be applied to the bar. kN in 2 decimal places

In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm². The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. D 1.7m 1.7m x-P B 3.5m7 Find the magnitude P of the largest additional vertical force that can be applied to the bar. kN in 2 decimal places

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
Calculate the vertical reaction at support D. Enter your answer in kN to two decimal places.
The cylinder of weight, W, shown below is being hoisted up with the force F against the vertical wall. If us = 0.57 a. Determine the reaction force (resultant of normal force and frictional force) against the vertical wall. b. Calculate the force, F, needed to set the cylindrical roller in motion W or W1 (in kN) = 516
Why is the force Fd pointing downwards? By force equilibrium, shouldnt it be 3 + Fd = 9 Fd = 6kN, thus pointing upwards?
Determine the bending moment 2.16 m to the right of point A for the beam shown belowif P = 1990 N, T = 4712 Nm, a = 0.99 m, b = 0.7 m, and c = 1.29 m. Round of the final answer (in N m) to four decimal places.
Q1) For the force system shown in figure, 1) Find the angle (¢) so that the resultant of these forces will be vertical. 45 kN S5 kN 3m
In the figure on the right where there is a single load of 50 N at point B of the given rod system, (between AB: 4m / BC: 1m) a) Calculate the support reactions? b) Immediately after support A, just before point B and immediately after and just before the C-bracket Find the cross section effects by cutting? c) Draw the cross section effect diagrams?
Find the force in member BD.A 40 lb ladder 12 ft long leans against the wall making an angle of 30° with the wall. When a 180 lb man reached a point 8 ft from the lower end, the ladder is about to slip. Calculate the coefficient of friction between the ladder and the floor. The coefficient of friction between the ladder and the wall is 0.20
In the figure on the right where there is a 50 N single load at point Bof the given rod system, (between AB: 4m / BC: 1m)a) find the support reactions?b) Immediately after support A, just before point Band immediately after and just before the C-bracketFind the cross section effects by cutting?c) Draw the cross sectional influence diagrams.
Determine the bending moment 2.25 m to the right of point A for the beam shown below if P = 1705 N, T = 3205 Nm, a = 0.95 m, b = 0.97 m, and c = 1.15 m. Round of the final answer (in N m) to four decimal places
look for and show complete solution: a. Reactions b. Shear and Moment Diagramc. Maximum Momentd. Equations w=022 Kn/m
A man exerted a force of 60 lbs at B as shown in the figure. Compute the angle theta in degrees. Compute the tension of the cable CAD in lbs.