In the figure below, the rigid beam of negligible weight is supported by a pin at O and vertical rods. Find the vertical displacement of the 62-kip weight. Bronze A = 2 in.2 E= 12 x 106 psi ← 4ft O The vertical displacement. 9ft 3 ft Steel 10 ft A=0.5 in.2 E = 29 x 106 psi 5ft 62kips inches 2 decimal places

In the figure below, the rigid beam of negligible weight is supported by a pin at O and vertical rods. Find the vertical displacement of the 62-kip weight. Bronze A = 2 in.2 E= 12 x 106 psi ← 4ft O The vertical displacement. 9ft 3 ft Steel 10 ft A=0.5 in.2 E = 29 x 106 psi 5ft 62kips inches 2 decimal places

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the bending moment 5.94 ft to the right of point A for the beam shown below if P = 1067 lb, W = 377 lb/ft, T = 5529 lb ft, a = 3.03 ft and b =5.96 ft. Round of the final answer (in lb ft) to four decimal places.
Determine the displacement of point B of the steel beam as shown. Take E = 200 GPa, I = 500(106) mm4.
For the steel rigid frame in Figure P8.31, com- pute the rotation of joint B and the horizontal displace- ment of support C. Given: E = 200 GPa, A = 500 mm2 , I = 200 × 106 mm4
2. (CASTIGLIANO'S THEOREM) Determine the vertical displacement of point B of the beam shown below. E= 200 GPaI= 150(10) mmsP= 15.4 kNQ= 6.4 kN/ma = 6 m
Using forced method of analysis, determine the reaction of supports from the beam shown in the figure. EI is constant. Possible Answers: Ay=698/27 kN (Upward) By=1484/27 kN (Upward) Cy=518/27 kN (Upward)
Calculate for the axial force in kN at member BA of the frame shown in figure 2 using cantilever method. Enter absolute value and use 2 decimal places in your solution. a = 33.8 kN b = 27.2 kN C= 4.8m
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
Compute all reactiosn for the beam in FigureP9.15 assuming that the supports do not move; EI is constant. (b) Repeat computations given that support C moves upward a distance of 288/EI when the load is appleid
Double Integration The given overhanging beam is loaded as shown. Use E = 1.5 x 10^6 psi and I = 40 in^4. A) determine the deflection at point B in inches. B) determine the location of the maximum deflection from the left support in ft. C) determine the maximum deflection in inches and calculate the slope of elastic curve over the right support.
Draw the shear-force and bending-moment diagrams for the beam shown. Determine the bending moment 6.2 ft to the right of point A if P = 2.19 kips and Q = 5.58 kips. Round off the final answer (in lb ft) to two decimal places.
Beam ABC is fixed at support A and rests(at point B) upon the midpoint of beam DE (see partaof the gure). Thus, beam ABC may be representedas a propped cantilever beam with an overhang BCand a linearly elastic support of stiffness k at point B(see part b of the figure).The distance from A to B is L =10 ft, the distancefrom B to C is L/2 = 5 ft, and the length of beamDE is L =10 ft. Both beams have the same flexuralrigidity EI. A concentrated load P =1700 lb acts atthe free end of beam ABC.Determine the reactions RA, RB, and MA for beamABC. Also, draw the shear-force and bending-momentdiagrams for beam ABC, labeling all critical ordinates.
Determine the bending moment 5.37 ft to the right of point A for the beam shown belowif P = 916 lb, W = 365 lb/ft, T = 5917 lb ft, a = 3.54 ft and b =5 ft. Round of the final answer (in lb ft) to four decimal places.