In the figure shown below, set F1 710 lb, F2 = 120 lb, F3 = 320 lb, the shaft diameter to 0.5 in, the shaft length to 14 in and the gear radius to 7 in. Determine the magnitude of the shear stress for the element of material at point A. Input your answer in units of ksi. F3 F1 F2

In the figure shown below, set F1 710 lb, F2 = 120 lb, F3 = 320 lb, the shaft diameter to 0.5 in, the shaft length to 14 in and the gear radius to 7 in. Determine the magnitude of the shear stress for the element of material at point A. Input your answer in units of ksi. F3 F1 F2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.4P: The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft...

See similar textbooks

Related questions

Q: Find the specific volume for state 1 in ft3/lb. b) Find the specific volume at state 2 in Ft3/lb

A: Need to find Specific volume for state 1 and 2

Q: In a condenser containing air and water, the air pressure is 22 kPa absolute. What is the gage press...

A: Given data, Pa(abs) =22 KPa h= 1.25 m

Q: n in the figure below, a closed, rigid tank fitted with a fine-wire electric resistor is filled with...

Q: An aluminum alloy [E = 10,000 ksi; ơy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi; O...

Q: 6-47* A beam is loaded and supported as shown in Fig. The beam has a uniform cross section and weigh...

A: Resolving the uniformly distributed load of magnitude 400 ×10= 4000 lb , which acts at the mid secti...

Q: Find the total (resultant) pressure acting on the tail end of the container containing gasoline (S =...

A: We will solve the problem using D'Alemberts theorem, Resultant force acting at the tail of contain...

Q: l engine is 30%. If air to fact ratio by weight is 20 and calorific value of fuel is 41800 kJ/kg. Fi...

Q: The flight path of the helicopter as it takes off from A is defined by the parametric equations x = ...

Q: What is the shear rate of a

A: Given: flow rate= 10 kg/min density=0.9 g/c L=10 cm w=25 mm t=3 mm To determine: shear rate

Q: 2.0 lb of water inside a piston-cy inder assembly undergoes the following two processes in series Pr...

Q: A propped cantilever beam is loaded as shown. Determine the reactions at A and D (positive if the fo...

Q: A wall is made from a quarter circle and flat plate with h = 4 m, R = 1.5 m, and w 3 m. The water is...

A: we will use projected area for horizontal force for vertical force we will use weight of fluid that ...

Q: Two model rockets are fired simultaneously from a ledge and follow the trajectories shown. Neglectin...

Q: 5-86. Operation of exhaust and intake valves in an automobile engine consists of the cam C, push rod...

A: Given Data The copression of the spring is: 20 mm=0.02 m The stiffness is: 300 N/m To Determine T...

Q: A 1.875-in-diameter solid steel shaft supports loads PA = 360 lb, Pc = 520 lb, and PE = 360 Ib, as s...

Q: A particle is observed to start at rest and accelerates at a = 30 + 2t, where t is in seconds, until...

Q: Blocks A and B are released from rest in the positions shown. Neglecting friction between all surfac...

Q: need help finding dimension x and y in the casting shown 2.80 cm 5.20 cm 6.00 cm 2.50 cm E 7.20 cm

A: Draw a diagram for the given problem.

Q: Q3: As shown in figure, find that at what distance body A will attain a velocity of 3 m/s from 2000 ...

A: To obtain the solution to the given question, we must the three statics equations which are- 1. The ...

Q: An electronic component with dimension of 5 cm wide, 6 cm high, and 9 cm long is cooled by aluminum ...

A: Fins are used to improve heat transfer from surfaces in a variety of applications. When the availabl...

Q: 2. Projectile Motion - D(ais)ynamics (12) The cat Daisy (pictured to the left) enjoys sitting on her...

A: Calculated how far back from the platform d must she jumped so that she reached the top edge of the ...

Q: Oil at 38 deg. Celsius is being drawn from a closed tank having a pressure of 70 kPa gage. The level...

Q: An aluminum pipe has a length of 75 m at a temperature of 18°C. An adjacent steel pipe at the same t...

A: Using formula, ∆LL=αT

Q: The object shows the center of the whole is three inches from the left surface and one inch from the...

A: we have to determine what kind of dimensions are used in the hole

Q: Two kg of water at 105°C and a quality of 50% (i.e. x = 0.5) is first heated until the piston locks ...

A: Given; m = 2kgT1=105°Cx1=0.5T3=90°Cx3=1

Q: Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the s...

A: Given Data The torque transmitted by the shaft is: T=1300 N·m The allowable stress is: τall=40 MPa ...

Q: At a production machine, parts arrive according to a Poisson process at the rate of 0.35 parts per m...

A: Given:arrival rate, λ=0.35 parts per minuteservice rate, μ=12=0.5 per minute

Q: 2. Determine the angular velocity of the gear and the velocity of its center O at the instant shown....

A: Calculated angular velocity of gear and velocity of the centre at this instance.

Q: A particle is traveling along the parabolic path y = 0.3x² . If x = 8 m, Vx %3D = 8 m/s, and a, = 3 ...

A: The calculated magnitude of acceleration at this instant.

Q: A high flying jet cruising at 3000km/hr displays a mach number of 3.2. What is the speed of sound an...

A: Mach number is defined as the ratio of local flow speed to the speed of sound. M=vc v=3000 km/hrv=30...

Q: Discuss Figure 3 in details, including: a) Basic components required to have such those system b) Ad...

A: The given figure shows the Flexible Manufacturing System (FMS) in flexible manufacturing system con...

Q: EXAMPLE 1 DETERMIE THE RESULANT MOMENT OF THE FORCES .SHOWN ABOUT POINT O 10 4 3 22 3m 30 15 1m 35 2...

Q: ne space constant for a resistance of 10

A: Need to find space constant foran axon.

Q: A 60 mm diameter pipe enlarges to a 90 mm diameter pipe. In the smaller pipe, the density of a stead...

A: given; →inlet pipe diameter(D1)=60mm=0.06m→outlet pipe diameter(D2)=90mm=0.09m→inlet velocity(v1)=40...

Q: 1. Determine the volume of an object that weighs 5 lb in water and 7 lb in oil of specific gravity 0...

A: Given data Weight of object in water = 5 lb Weight of object in oil = 7lb Specific gravity = 0.82 We...

Q: Gas at 1.5 bar abs. and 20 °C in a closed vessel is compressed to 10 bar abs. Its compressed tempera...

A: The value of 'n' can be calculated using the characteristics equation for Polytropic processes which...

Q: Ball A is thrown straight up with an initial speed v, and reaches a maximum elevation h before falli...

A: Given data: initial speed=v0Maximum height=h Need to determine the height when they meet.

Q: The 50-kg homogeneous smooth sphere rests on the 30° incline A and bears against the smooth vertical...

Q: A tank 1.5 m stands on a trolly and is full of water. It has an orifice of diameter 0.1 m at 0.3m fr...

A: Given:h=1.5 md=0.1 mCd=0.6

Q: A piston/cylinder setup contains 1 kg of air at 20°C with an initial volume of V1=0.1 m3. Initially,...

Q: 4-3.18. Repeat Prob. 4-3.17 if the loads Q are zero and each load P = 2000 lb.

Q: A cylindrical boiler with an outside diameter of 3.60 m and a wall thickness of 40 mm is made of a s...

Q: What is the center of gravity in this figure?

A: given; center of gravity on given figure?

Q: 3. The pump of a water distribution system is powered by a 15 kW electric motor whose efficiency is ...

Q: In a casting machining company, it takes an operator 30 seconds to load ,15 seconds to unload each m...

Q: Problem 3.50 Y Body D is in equilibrium when cable AC suddenly breaks. If B is fixed, does the tensi...

A: In the given figure, when the cable AC is breaks than the mass start moving in circular path with ra...

Q: A Pelton wheel has to develop 12 MW under a head of 300 m at a speed of 500 rpm. If the diameter of ...

A: Given Data The shaft power is: P=12 MW The speed is: N=500 rpm The head is: H=300 m The efficiency ...

Q: 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be...

Q: The flat square of side length 2 m is submerged vertically in water, 2 m below the surface as shown...

A: GIVEN DATA - FLAT SQUARE PLATE GIVEN 2m*2m WEIGHT DENSITY OF WATER =9810N/m3 WE HAVE TO FIND FORCE E...

Q: How can you give the effect of the hydraulic brake

A: Given Data : Effect of hydraulic break

Question

In the figure shown below, set F1 = 710 Ib, F2 = 120 lb, F3 = 320 lb, the shaft diameter to 0.5 in, the shaft length to 14 in and the gear radius to 7 in.
Determine the magnitude of the shear stress for the element of material at point A. Input your answer in units of ksi.
F3
F1
F2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
The stresses acting on a stress element on the arm of a power excavator (see figure) are ax= 52 MPa and txy= 33 MPa (sec figure). What is the allowable range of values for the stress if the maximum shear stress is limited to = 37 MPa?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.