In the figure shown, the voltage at Vxy is equal to

Q: Problem 1. A Darlington Transistor is composed of two NPN transistors. Given transistor Ql's gain B1...

A:

Q: The SCR operation characteristic is plotted for la (anode current) vs lg (gate current), Va (anode –...

A: Silicon Controlled Rectifier (SCR) is the most important and widely used member of the thyristor fam...

Q: A polarity test is performed upon 1150/115-volt transformer. If the input voltage is 120 V, calculat...

A:

Q: Given the circuit below, calculate the voltage drop across R2 when the voltage on each LED is 3 volt...

A:

Q: In the circuit shown, the coil has inductance and resistance. When X is joined to Y, the time consta...

A: In steady state=P=I2REnergy stored in inductor =12LI2τ=LRAfter connecting x and z, the whole energy ...

Q: (a) Describe the difference between displacement power factor and true power factor. (b) Briefly exp...

A:

Q: D2 R2 추 mA Germanium D1 R1 Silicon E1 E2

A: The solution is given below 

Q: Q1: For the cascaded system of Fig. 1, determine: (a) The loaded voltage gain of each stage.(b) The ...

A: In order to improve the total gain of the system the amplifier are connected in cascade. The overall...

Q: Find the total resistance at terminal a-b

A: To solve above problem, one should know how to find equivalent resistance for series and parallel ci...

Q: if an fir has 27 taps, how many unit delay elements are needed

A: FIR filter has 27 taps then how many unit delay elements are needed ?

Q: A 16 pole, 3Φ synchronous generator has a resultant air gap flux of 0.06 wb per pole. The flux is d...

A:

Q: b) Assume that the transmitted signal is s(t) = cos(300 x 10°71) %3D Determine the received signal w...

A: Transmitted Signal- Transmitted Signal is define as the signal which is to be transmitted with the h...

Q: For the circuit given in the figure, a) determine the impedance b) the circuit current c) the power ...

A: Here, we have given an electrical circuit having the series parallel combination of resistors and in...

Q: Logic gate No. 6 DOU Dov. D Y B W C

A:

Q: The voltage phasor diagram for a certain series RLC circuit is shown in Figure below. Find the maxim...

A: Step 1-Given:∆VL=193V∆VC=75V∆VR=124VTo find-∆Vmax(in volt)

Q: R, 10uF Emitter - follower CE amplifier i ka 10uF 4- 50 k2 2,-12 k2 R222 ka 2-4.6 ka 640 Z- 202

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are...

Q: Given an input sinewave of 20Vpk-pk with its axis at the origin. If the axis is raised to 10V, at wh...

A: Option B  0 volts Just shift the waveform 10v up  So the values will be added 10 to every point So i...

Q: (c) Two (2) ideal voltage sources, V1 and V2 are connected together by a line impedance, Z. (i) Draw...

A:

Q: What is the power transmitted by the isotropic radiator having a field intensity of 1.51 V/m at 6om?...

A: Note : After calculating the power transmitted by the isotropic radiator we come to know that none o...

Q: 5. When you touch the twisted wire with the positively charged pen, the electrons travel from the fo...

A: “Since you have asked multiple true/false questions, we will solve the first three questions for you...

Q: R13 3300 R11 5602 R 14 V3 5602 R12 12V 220Ω 10

A:                                                                  

Q: 2) A light sensitive switch needs a voltage of 0.45V to compare to the voltage coming from the light...

A:

Q: 2) For the system shown below, find the magnitude of the force experienced by charge Q, and state it...

A:

Q: The ratio of the terminal voltages is: 10 9.2 10.5 9.5

A:

Q: Design a differentiator to have a time constant of 10-2s and an input capacitance of 0.01µF. What is...

A: Given,Time constant τ=RC=10-2sand C=0.01μFSo,R=τC=10-20.01×10-6R=1MΩ      

Q: Find the load current IL by use of norton’s theorem

A: We find the Norton equivalent circuit of the given circuit to find load current iL 

Q: In the circuit in the figure, the apparent power (S) of the second arm is given as 1490 VA. Accordin...

A:

Q: 4.1 Assume that an ideal transformer used to step down 13.8–2.4kV and that it is fully loaded when i...

A:

Q: A wire with length 120cm is placed along x-axis and carrying 10A current coming out of the axis. It ...

A:

Q: 3-phase wye connected alternator is rated at 1600 kVA, 13.5 kV. The armature resistance and synchron...

A:

Q: A tor the creuit Shown beluo where all resislors are given in k2, apply Transformation technique to ...

A:

Q: (c) A 230 V, 50 Hz power source is connected to the some loads, the source is supply current with po...

A:

Q: Briefly explain TWO (2) disadvantages of low power factor.

A: Power factor angle (φ) is the angle between the voltage (V) and the current (I)

Q: 9. Which of the following equation represents mass action law for semiconductors in electronic circu...

A: In this case, the correct option corresponding to the law of mass action for semiconductors needs to...

Q: 2300V to 230V step down transforme ave the following resistances and induc Re' =0.093 ohm Re" = 0.00...

A:

Q: State advantage and disadvantage of delta-connected three-phase voltage source compare to the Y-conn...

A: Delta connected system has a closed path including the sources and is independent of load.  Where as...

Q: The switch has been closed for a long time before it opens at t = 0. After the switch opens, find th...

A: Brief description : Generally transient analysis is applicable only for the circuit which have energ...

Q: SP 7: Using superposition, find the current l, in the circuit. 3 kx 42 Io

A:

Q: 4- Consider the following arbitrary fields. Find out which of them can possibly represent electrosta...

A:

Q: When t 0, is = l1 Find v(t) = A ·e¯h +B__for t > 0 10 Ω is v(t): 10 Ω 20Ω Given Variables: 10:1A 1:3...

A: In this question we need to find a value of A , B and time constant.

Q: The regulation of a 250 volt shunt generator is 6 percent. Calculate the no load voltage.

A: GivenFull load volatge=250 vPercentage of regulation=6%

Q: Calculate IR3 in mA of the circuit with R1=1228 ohms, R2=2326 ohms, and R3=3158 ohms and a supply vo...

A:

Q: A balanced three-phase delta connected source supplies to a balance three-phase star connected load,...

A:

Q: Find the Laplace impedance of a series parallel circuit where 2Ω resistor is in series with the para...

A: It is given that: R=2 ΩL=2 HC=0.5 F    

Q: If A - B = 0, is it necessarily true that A = B? (A and B are vectors) Select the correct response: ...

A: Let A = Axax+Ayay+Azaz and B = Bxax+Byay+Bzaz

Q: 1. What do you understand by the term 'back e.m.f.' ? A d.c. motor conn mature resistance of 0.15 2....

A: Given      A d.c motor withSupply voltage V=460 vArmature resistance Ra=0.15 Ω

Q: In order to keep 10 gram current carrying conductor with 40 cm length suspended inside a magnetic fi...

A:

Q: Calculate the total current in the circuit below; R ell 100 mH 520° V

A: Given that Vs=5∠0L=100mHR=133Ωf=140Hz

Q: The circuit Gn be draun as, R is 102 26MH VIH) = 200V gin (250 t)

A: Resistance, R = 10 Ω Inductance, L = 25 mH Angular frequency, ω = 250 rad/s Supply Voltage, V = 2002...

Q: EXERCISE 9 Include fprintf in exercise 6 to print the roots of the quadratic equations with the foll...

A:

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.