Inside a helical spring of circular cross section 20 mm in diameter. Another spring is placed having the same cross -section The mean radius of the outer spring is 80 mm where as that of the inner spring is 50 mm. Both the springs are of the same height and have 10 coils each. With a load being transmitted to both the springs they defeat by 50 mm. In which spring is the maximum shear stress greater, and what are their magnitudes? What is the corresponding load being transmitted? The shear modulus C=80GPA for both the spring materials.

Inside a helical spring of circular cross section 20 mm in diameter. Another spring is placed having the same cross -section The mean radius of the outer spring is 80 mm where as that of the inner spring is 50 mm. Both the springs are of the same height and have 10 coils each. With a load being transmitted to both the springs they defeat by 50 mm. In which spring is the maximum shear stress greater, and what are their magnitudes? What is the corresponding load being transmitted? The shear modulus C=80GPA for both the spring materials.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.10P: The tensional pendulum shown in the figure consists of a horizontal circular disk of a mass M = 60...

See similar textbooks

Similar questions

Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
A helical compression spring is to be used for a maximum load of 1.5 kN using the spring index of 8. The maximum permissible shear stress for the spring wire is 400 MPa. Which of the following is the wire diameter of the spring to be used?
The corediameter of the double start square threaded screw having a pitch of 12mm is 50 mm. A load of 18kN is lifted through a distance of 180mm. Find the work done(in Joule)in lifting the loadand the efficiency of the screw, when 1. The load rotates with the screw, and 2. The load rests on the loose head which does not rotate with the screw. The external and internal diameter of the bearing surface of the loose head are 60 mm and 10 mmrespectively. The coefficient of friction for the screw is 0.11,whilefor the bearing surface is 0.13.
Ensssprrs wuii. Inside a helical spring of circular cross-section 20 mm in dimater spring is placed having the same cross-section. The mean radius of the outer spring is 80, that of the inner spring is S0 mm. Both the springs are of the same height and have 10 coils With a load being transmitted to both the springs they deflect by 50 mm. In which spring is the maximum shear stress greater, and what are their magnitudes? What is the corresponding load being transmitted? The shear modulus C = 80 GPa for both the spring materials.
A helical spring in which the mean diameter of the coil is 8 times the wire diameter is to be designed to absorb 0.2 kNm of energy with an extension of 100 mm. The maximum shear stress is not to exceed 125 N/mm2. Determine the mean diameter of the spring, diameter of the wire and thenumber of turns. Also find the load with which an extension of 40mm could be produced in the spring. Assume G = 84 kN/mm2.
The inner spring of a compound helical spring is arranged within and concentric with the outer one and is shorter by 9 mm. The outer spring has 10 coils with a mean diameter of 24 mm and a wire diameter of 3 mm. (a) Determine the stiffness of the inner spring when an axial load of 162 N causes the outer spring to compress by 16 mm. If the radial clearance between the springs is 1.5 mm and the inner spring has 8 coils, find its wire diameter. (c) Disregarding the effect of curvature, find the maximum shear stress in each of the spring. Given G = 78 GPa.
A shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: (a) The magnitude of the mass in plane E and its angular position relative to the mass in plane A (b) The distance of the plane E from plane A (c) The dynamic loading on each bearing when the mass in plane E has been attached and the shaft rotates at 200 rev/min. For the bearing loads in the opposite direction determine all the unknown values. For the bearing loads in the same direction, show the diagrams and equations only to use for a possible solution.
A shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. USING THE METHOD OF DRAWING m*r and m*r*l diagram Determine: The magnitude of the mass in plane E and its angular position relative to the mass in plane A The distance of the plane E from plane A The dynamic loading on each bearing when the mass in plane E has been attached and the shaft rotates at 200 rev/min. For the bearing loads in the opposite direction determine all the unknown values. For the bearing loads in the same direction, show the diagrams and equations only to use for a possible…
A shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: The magnitude of the mass in plane E and its angular position relative to the mass in plane A The distance of the plane E from plane A PS – Use graphical methods to solve the balancing problem
A shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: The dynamic loading on each bearing when the mass in plane E has been attached and the shaft rotates at 200 rev/min. For the bearing loads in the opposite direction determine all the unknown values. For the bearing loads in the same direction, show the diagrams and equations only to use for a possible solution. PS – Use graphical methods to solve the balancing problem
A typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: Mean coil diameter = 100mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: Mean coil diameter = 75 mm No. of turns = 20 Both the springs are of equal initial length when unloaded. If the working stress for each spring is to be the same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following: a. Diameter of steel wire for inner spring b. Stiffness of inner spring c. Stiffness of the compound spring
A transmission shaft is supported on two bearings which are 1m apart. Power is supplied to the shaft by means of a flexible coupling, which is located to the left of left hand bearing. Power is transmitted from the shaft by means of a belt pulley, 250 mm diameter, which is located at a distance of 300 mm from the left hand bearing. The mass of the pulley is 20 kg and the ratio of belt tension on tight and slack sides is 2:1. The belt tensions act vertically downward. The shaft is made of steel with yield stress 300N/mm2 and the factor of safety is 3. Determine the shaft diameter, if it transmits 10 kW power at 360 rpm from the coupling to the pulley.