Show solution Calculate the reading of each wattmeter in thecircuit in Fig. 11.20 if the phase voltage at theV and (a) Zój6 N; (c) Zó = 5 + j5V3 N; andload is120= 8 + j6 N;(b) Z4 = 8 –(d) Z = 10 /-75° N. (e) Verify for (a)-(d) thatthe sum of the wattmeter readings equals the totalpower delivered to the load.%3DAaссW1pcZ4 = |Z|Z0 VANBbeONW2pcV CNccС+Figure 11.20 A A circuit used to analyze thetwo-wattmeter method of measuring average powerdelivered to a balanced load.m

Answered: Image /qna-images/answer/1b585c43-b7f8-4dec-b603-0293a4ce1a5e.jpg

ircuit in Fig. 11.20 if the phase voltage at th pad 5) Z4 = 8 – j6 N; (c) Z, = 5 + j5V3 N; an = 10 /-75° N. (e) Verify for (a)–(d) tha is 120 V and (a) Za = 8 + j6 f. - 1) Z ne sum of the wattmeter readings equals the tota ower delivered to the load. %3D A a cc W1 pc Z4 = |Z|Z@ VAN %3D B be W2 pc VCN cc С+ +1

ircuit in Fig. 11.20 if the phase voltage at th pad 5) Z4 = 8 – j6 N; (c) Z, = 5 + j5V3 N; an = 10 /-75° N. (e) Verify for (a)–(d) tha is 120 V and (a) Za = 8 + j6 f. - 1) Z ne sum of the wattmeter readings equals the tota ower delivered to the load. %3D A a cc W1 pc Z4 = |Z|Z@ VAN %3D B be W2 pc VCN cc С+ +1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 25 kVA, 240 V single phase source supply the rated power at the rated voltage to a motor at 0.8 power factor lagging. Find the capacitor bank in order to improve the power factor to 0.9 lagging connected to a motor.a. Calculate the real power, reactive power and current before capacitor bank is connected? b. Calculate the power and reactive power after capacitor bank is connected? c.What is kVA rating of capacitor bank QC?
It is desired to correct the 2,400-kVa 0.65 lagging power factor load in a plantto unity by the installation of a synchronous condenser. Calculate the kilovoltampere rating of the latter. Ans.: 1824 kVA
An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance (capacitive) ZC = (8 – j20) ohms. Calculate (a) the conductance and susceptance of each branch; (b) the total conductance, susceptance, andadmittance of the circuit; (c) the current in each branch, and the total current and power factor, if the impressed emf is 120 volts. draw the circuit diagram
Design a power factor correction circuit with the value of parallel capacitance needed tocorrect a load of 179 kVAR at 0.85 lagging pf to unity pf. Assume that the load issupplied by a 110-V (rms), 60-Hz line.
Two 3Ø alternators are supposedly operating in parallel and supplying a total load of11kV, 1500kW at a pf of 0.866 lagging. Initially, one alternator supplies ¼ of the totalpower at 60Hz. The other alternator supplies ¾ of the total power at 59.9Hz. Thesynchronous reactance of each is 50/Ø and the effective AC resistance at 25⁰C is 4/Ø.Without changing any given data, determine the generated voltage of the 2nd alternator
When the three identical star-connected coils are supplied with 400 V, 50 Hz, 3-phase supply, the 1-phase wattmeter whose current coil is connected in line R and pressure coil across the phase Rand neutral reads 6 kW and the ammeter connected in R-phase reads 30 Amp. Assuming RYB phase sequence find: (i) the power factor, of the load, (ii) resistance and reactance of the coil (iii) reactive power of 3-phase load and (iv) Apparent Power Power Factor, of the Load Reactance Resistance Reactive Power Apparent Power
2. Solve the following problem: A THREE-PHASE PLANT CONSUMES 600 KVA, WITH A VOLTAGE OF 2400 VOLTS AND A POWER FACTOR OF 0.8 BEHIND. a) DETERMINE THE EQUIVALENT DELTA IMPEDANCE OF THE PLANT. b) IF THE PLANT WERE A STAR, CALCULATE THE RESISTANCE, REACTANCE AND THE CORRESPONDING PASSIVE ELEMENT.
If a 3- Ø, Y-connected system has a line-to-line voltage of 1103Sin(377t) V, then the line-to-neutral (RMS) voltage would be:
A three-phase system includes a 346.4 V line-to-line supplying a three-phase motor rated 15KVA 0.8pf lag plus additional balanced constant impedance loads. The single-phase representation of the system is shown below. Assume that sources and loads are Y-connected. 1. What is the RMS value of the line current, I in A? 2. If this set of loads will be supplied through a service transformer. What should the minimum size of the transformer in kVA? 3. What should be the size of three-phase capacitor(that will be added to the load mix) to improve power factor to almost 0.95 lag?
A single phase wattmeter is used to determine the power taken by a three phase squirrel cage induction motor. The current coils is placed in line 1 while the potential coil is shifted from lines 1 and 2, then from lines 1 and 3 respectively. If the wattmeter registers 5760 and 3380 watts respectively, what is the line current drawn by the motor. Line to line voltage is 230 V.
A Δ-connected, 60−Hz, balanced, 3ϕ, positive-sequence voltage source is connected to a Δ-connected, symmetric 3ϕ load via a non-ideal transmission line. The line-line voltage magnitude of the source is 480VRMS. The series impedance of each phase of the transmission line is 0.1+j1.5Ω. The impedance of each leg of the load is 3+j6Ω. a. What is the total, 3ϕ complex power consumed by the load. b. What are the total active power losses (all three phases) in the transmission line?
please solve this question with complete solution : A 50 Hz, 250 V single phase power line has the following loads placed across it in parallel; 4 kW ata pf of 0. 8 lagging; 6 kVA at a pf of 0.6 lagging; 5 kVA which includes 1.2 kVAR leading. Determinethe overall pf of the system and the capacitance of the capacitor which, if connected across themains restore the power factor to unity.