Fluid mechanics I Gate AB in the Figure below is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric pressure, compute the force F on the gate andits center-of-pressure position X.- The specific weight of water is 9790 N/m36 mOil,SG = 0.824 m8 mAK1.2 mImB40°

Answered: iš 1.2 m long and 0.8 m into the paper.…

Engineering

Mechanical Engineering

iš 1.2 m long and 0.8 m into the paper. Neglecting atmc on X. er is 9790 N/m3 4 m

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Related questions

Q: Calculate the rise of a liquid of density p = 0.8 g cm-3 inside a square straw, with the cross…

A: Given; Density of the liquid, ρ=0.8 g/cm3=800kg/m3 Side of the square cross L=2 mm Surface tension…

Q: re base (Fig Q3} of size 5 m x 5 ereby the surface height, in me- n by the function: 1)2 + 5

A: Given data Side of the square= 5m Hight of the container = - 0.1(5-1)2 +5 = -0. 1×16+5 =3.4 mm So…

Q: Evaluate the total force on the gate (unit width) and its direction. (specific weights of Water:…

A: Given data Specific weight of water = 9790N / m3

Q: Calculate the height of capillary rise in a glass capillary tube having a radius of 3.5 x10-5 m. The…

A: Given data : Surface tension σ=72.7 mN/m Radius R=3.5×10-5 m Acceleration due to gravity g=9.81 m/s2…

Q: A certain torpedo, moving in fresh water at 10 8 C, has a minimum-pressure point given bythe…

A: Given data: Pmin = P0 - 0.35 ρV2 P0 = 115 kPa The torpedo is accelerating from zero velocity to V.…

Q: A cube of lead with a side dimension of 5.0 cm is slowly lowered into the beaker of oil by a thin…

A: “Since you have posted a question with multiple sub-parts, we will solve first two sub-parts for…

Q: 4. Water is flowing in a pipe with radius of 25.4 cm at velocity of 5 m/s. The viscosity What is its…

Q: Q.2 As shown in Fig.Q2, a vertical concentric annulus, with outer radius r. = 50mm and inner radius…

A: Given, r0=51 mm=0.051 mri=50 mm=0.050 mY=0.0662 N/mSG=0.9θ=100

Q: 10- Find the height of blood in the capillary tube resulting from the addition of (10 cm) of blood…

A: Given, Volume, V=10cm3Density, ρ=1.051gm/cm3Viscosity, μ=2.3×10-3Pa.secLength of…

Q: Patm 0.5m A Hg Dr=0,85 I X 0.2m agua fig # 1 1,5 m

Q: Oil relation between the shear stress and rate of deformation is given in the figure, If the oil…

A: The relation between shear stress and rate of deformation is - τ=μdudyμ=τdudyThe slope of the graph…

Q: Patm T 0.5m F F Hg Dr=0,85 I 102m agua fig # 1 B. 1,5 m

Q: The dam for a lake is designed to withstand the additional force caused by silt that has settled on…

A: →Given , density of silt=ρ2=1.76x103 kgm3 →Assume at first there is only water in the…

Q: Here, a liquid's density is to be determined by a 1-cm diameter cylindrical hydrometer whose…

Q: The belt moves at a steady velocity V and skims the op of oil tank. Assuming a linear velocity…

Q: By neglecting friction, ( a ) use the Bernoulli equationbetween surfaces 1 and 2 to estimate the…

A: Part A) The incompressible Bernoulli equation between surfaces 1 and 2 yields.

Q: A square block weighing 1.1 kN and 250 mm on an edge-slides down an incline (20° with horizontal) on…

Q: Base radius ro Oil 20 A solid cone of angle 104.8 degrees, base 15.2 cm, and density 2745 kg/m3 is…

Q: 4. The belt in the figure moves at steady velocity V and skims the top of a tank of oil having…

Q: A = A . [1-x/ (2 L) ] Densityp L

A: Take a strip of thickness dx at a distance x. Then the force acting on the strip is,…

Q: Detemine the horizontal and vertical components of the liquid pressure acting on the semicylindrical…

Q: Q3. A piston having a diameter of 14 cm and a length of 25 cm slides downward with a constant…

A: Given data: Piston diameter, D=0.14mPiston length, L=0.25mFilm thickness, t=0.005×10-2mPiston force,…

Q: 8m- 3m Oil, sg.-a81 - Gate AB in figure is 1.0 m long and 0.9 m wide. Calculate force F on the gate…

A: Given Length of gate =1 m width of gate =0.9m ρoil=0.81×1000 To determine :- Force on the gate and…

Q: A smooth sphere of diameter d is dropped into a calm ocean. Data: d = 20 cm; Sphere material's…

A: Given that, Diameter of sphere, d=20 cm,Density of sphere, ρsm=3000 kg/m3Density of sea water,…

Q: A settling tank for municipal water supply is 2.5 m deep,and 20°C water fl ows through continuously…

A: The data given is, Water velocity, V = 35 cm/s = 0.35 m/s Water depth, h = 2.5 m Water temperature,…

Q: (2) Referring to the following figure, the distance between plates is Ay = 0.5 cm, Av: = 10 cm/s,…

Q: Torricelli’s idealization of effl ux from a hole in the side ofa tank is V = √2 gh, as shown in Fig.…

Q: A large open tank contains a layer of oil floating on water as shown. The flow is steady and…

A: Given data as per the question Total height of the tank =6 m Diameter of pipe at entry =0.2 m…

Q: Water with density Pwater = 1000 kg/m³, is transported in 30° circular pipe, inclined at an angle of…

A: For the given arrangement the density of manometric fluid = 13600 kg/m3 h = 12 cm To determine…

Q: 3.3 A 3 m diameter closed tank contains 0.61 m of mercury (s.g. =13.6), 1.524 m of water, 2.438 m of…

A: Given data

Q: The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity…

Q: A tainter semicircular gate is shown in the figure. Considering a ft wide strip, determine the…

A: Given:

Q: The 1m diameter tank is initially filled with gasoline. There is a 3.1 cm diameter orifice in the…

A: Given: Diameter of the orifice is 3.1 cm. Diameter of the tank is 1 m. Height drop from 2m to 1.5 m.…

Q: 30

A: For solution refer below images.

Q: Please answer the following question

Q: The shear stress at a point in a liquid is found to be 0.03 N/m2. The velocity gradient at the point…

A: Given data: The shear stress is τ = 0.03 N/m2. The velocity gradient is dv/dx = 0.15 s-1.

Q: final diameter

A: To determine the final diameter of ballon.

Q: If Re and Pr are identical in two problems, we can use the same average Nusselt number, even if…

A: Nusselt number has a empiriacal relation with Re and Pr

Q: 2. The shear stress developed in lubricating oil, of viscosity 9.81 poise, filled between two…

A: Given, Oil viscosity = μ = 9.81 poise = 0.981 Pa-s Distance between parallel plates = dy = 1 cm =…

Q: A cylinder is formed by bolting two semicylindrical channelstogether on the inside, as shown in Fig.…

A: Apply the Bernoulli equation to find surface pressure.

Q: In regions far from the entrance, fluid flow through a circular pipe is one dimensional, and the…

A: Given data as per question R = 0.07 m L = 35 m umax = 4 m/s μ = 0.0010 kg/m·s

Q: The iceberg idealization may becomeunstable if its sides melt and its height exceeds its width.…

Q: Find teh volume (m3) of teh water displaced for a wooden block of width 3.7 m and of depth D= 1.2 m,…

A: Calculate the volume of the block. V=LBD Here, V is the volume of the block, L is the length of the…

Q: Two immiscible liquids of equal thickness h are beingsheared between a fixed and a moving plate, as…

A: (a) The velocity of the interface is vL. Write the expression of shear stress for lower fluid.…

Q: 30 m length of smooth pipe? Calculate the total equivalent length of pipe that would produce a…

A: Given data :- Diameter D = 1 inch = 0.0254 meters Pressure drop (dp) = 70 kpa Mass flow rate m =…

Q: A hydraulic lift of the type commonly used for greasing automobile consists of a 280.18-mm- diameter…

Q: Gate AB is 4 m wide into the paper, find the value "X" in the figure below. 8m 3m Oil, (S=0.7) 8 m…

Q: The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity…

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

100%

Fluid mechanics I

Gate AB in the Figure below is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric pressure, compute the force F on the gate and
its center-of-pressure position X.
- The specific weight of water is 9790 N/m3
6 m
Oil,
SG = 0.82
4 m
8 m
AK1.2 m
Im
B
40°

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the Figure below, the cover gate AB closesa circular opening 80 cm in diameter. The gate is held closed by a 200-kg mass as shown. Assume standard gravity at 20 °C. At what water level (h) will the gate be dislodged? Neglect the weight of the gate. Specific weight of water 9790 N/m3
Consider a flatboat hull which carries cargo down a river. When fully loaded the craft weight 150 kN. How far will this boat sink into the water? (i.e., What is boat’s “displacement, D?”) Be sure to draw a free-body diagram that shows all external forces operating on the boat; also, show all relevant dimensions. Locate the center of buoyancy (ycb) from the bottom of the hull. If the metacenter (M) is located at 0.98 m from the bottom of the hull, is this boat stable?
A ship of displacement 36000 tonne carries oil fuel in four tanks 16.0 m long and 6.0 m broad, the tanks arranged with their length in the fore and aft direction. The specific gravity of the oil is 0.84, and the density of seawater inwhich the ship is floating is 1020 kgm-3. For a ship of this size, the metacentric height is at least 500 mm. What is the reduction of the metacentric height of the ship because of the oil that is contained in the tanks and how serious is this reduction? Please discuss further your conclusions.
The closed layered box in Fig. has square horizontalcross sections everywhere. All fl uids are at 20 ° C.Estimate the gage pressure of the air if ( a ) the hydrostaticforce on panel AB is 48 kN or ( b ) the hydrostatic force onthe bottom panel BC is 97 kN.
In Fig., the cover gate AB closes a circular opening80 cm in diameter. The gate is held closed by a 200 - kg mass asshown. Assume standard gravity at 20 ° C. At what water levelh will the gate be dislodged? Neglect the weight of the gate.
A conical vessel r=(b-z)tanA, rests with its open end downward on a flat surface, as shown in the figure. We want to fill it to a height h with a liquid of density p. What will be the lifting force on the vessel? (tanA: tangent of A)
The figure below shows a block of wood with total height H, submerged height h and square base with side b = 0.41 m, floating in a tank with water. a) Knowing that the wood density is d = 0.75, calculate: a) the ratio between the submerged height h and the total height of block H; b) the metacentric height, in meters, for the block to float, in the indicated configuration, with indifferent balance (critical); c) the value of H for the same situation as the previous item (indicate the unit).
A balloon weighing 3.5 lbf is 6 ft in diameter. It is fi lledwith hydrogen at 18 lbf/in 2 absolute and 60 ° F and isreleased. At what altitude in the U.S. standard atmospherewill this balloon be neutrally buoyant?
An underwater gate 8 m wide is held closed by a force, F, as shown in the figure. If the force is applied at the middle of the gate, what is the minimum value required to keep the gate closed? take density of water= 996kg/m3
A rectangular sea aquarium observation window is 119centimetres wide and 69 centimeters high. What is the force on this window if the upper edge is 6 centimeters below the surface of the water? The weight-density of seawater is 10065 N/m3. What is the total force of the fluid against the window?
Plz answer I will rate !:) A right circular cylindrical tank with its circular base on the ground is full of water. The diameter of the base is 4m and the height of the tank is 4m. Set up a Riemann sum to approximate the hydro static force against the lateral wall of the tank. Then express the force as an integral and evaluate it.
A cylinder is formed by bolting two semicylindrical channelstogether on the inside, as shown in Fig. Thereare 10 bolts per meter of width on each side, and the insidepressure is 50 kPa (gage). Using potential theory for theoutside pressure, compute the tension force in each bolt ifthe fluid outside is sea-level air.