A cylindrical tank is being filled with water. The tank is initially empty but then water begins to flow into it at a rate of 56.00 kg/min. There is a small hole of radius r= 0.9000 cm at the bottom of the tank where water can escape. Because the flow rate of water leaving the hole is initially at a slower rate than water entering the tank, the water level rises. The average velocity of water leaving through the hole at the bottom of the tank is not constant and is a function of the height of the water level in the tank: 9in v= 2gh dout where g is the gravitational constant of Earth, 9.81 m/s?. Additionally, the density of water at this temperature is 1.000 x 103 ka/m3

A cylindrical tank is being filled with water. The tank is initially empty but then water begins to flow into it at a rate of 56.00 kg/min. There is a small hole of radius r= 0.9000 cm at the bottom of the tank where water can escape. Because the flow rate of water leaving the hole is initially at a slower rate than water entering the tank, the water level rises. The average velocity of water leaving through the hole at the bottom of the tank is not constant and is a function of the height of the water level in the tank: 9in v= 2gh dout where g is the gravitational constant of Earth, 9.81 m/s?. Additionally, the density of water at this temperature is 1.000 x 103 ka/m3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A vertical cylindrical tank is 9 m high and 5 m in diameter. It is two thirds full of water and is rotated uniformly about its axis until on the point of overflowing. Compute the linear velocity at the circumference of the tank.
A cylindrical tank of water is 2.0 m in diameter and 3.5 m tall. There is a 2.0 cm diameter hole at the bottom from which water is leaking. A feeder pipe at the top of the tank, 4.0 m above the ground, delivers water at a rate of 0.020 m3/min. If the tank is initially half full, at what rate is the volume of water changing? Assume the tank is open to air at the top. Use a negative rate to indicate a decreasing volume and a positive rate to indicate an increasing volume.
A cylindrical tank of diameter 3m and height of 8m is filled halfway with water. A small hole (ID = 3cm) is at the bottom of the tank, where the water is flowing out. Determine the volumetric flow rate of the water at the point where 0.5m of water is left in the tank.
An open vessel 4.0m wide, 5.0m long and 3.5m deep contains 3m of water. It is then accelerated to the right along its width. a. Calculate the acceleration just about water to spill. b. At this rate, what is the force (in N) causing the acceleration if the mass of the vessel if the mass of the vessel is 600kg? c. Consider the same vessel accelerated at 7.00 m/s2. Determine the volume (in m3) of water spilled at that acceleration.
9. The depth of flow of water at a section of a rectangular channel of width 2 m is 0.3 m. The discharge through the channel is 1.5 m3/s. Determine the height of hydraulic jump and loss of energy per kg of water.
A 10 cm diameter sharp edged orifice (C=0.60) is located at the vertical side of a tank having a horizontal cross section 2 m square. An inflow of 23 L/s keeps the head over the orifice constant. If the inflow is changed to 34L/s, how long will it take for the head over the orifice to reach 2.0 m? a.260 seconds b.235 seconds c.35 seconds d.415 seconds
A liquid flows through a pipe with a diameter of 10cm at a velocity of 9cm/s. If the diameter of the pipe then decreases to 6cm, what is the new velocity of the liquid
An open rectangular tank 3.8m high, 2.5m wide and 6m long is filled with water at a depth of 2.2m. If it is accelerated at 2.3 m/s^2 and is moving at a plane inclined 15 degrees from the horizontal, determine the following: a. acceleration of the vessel along the horizontal; and b. angle of fluid inclination. Note: Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3.
An open cylindrical tank having a radius of 0.34 m. Is filled with water at a depth of 0.84 m. If it is rotated about its vertical axis to a velocity of 110 rpm, what should be the height in meters so that no water will be spilled out
An square open tank with base length of 1.8 meters contains 0.9 m of water. It is translated horizontally to the right with an acceleration of 4 m/s^2. (a) How high should the tank be so that no water will be spilled? (b) If acceleration is increased to 7 m/s^2, how much water will be retained?
Determine the diameter of an orifice that permits a tank of horizontal cross- section 1.5m2 to have its liquid surface draw down at the rate of 160 mm/s for a 3.35-m head on the orifice. Use C=0.63.
A vessel 2 m in diameter containing 4 m high of water is being raised upward. Find the pressure at the bottom of the vessel when; a.) the velocity is constant. b.) the vessel is accelerating 2.5 m /sec²? A vessel partly filled with liquid and moving horizontally with the constant linear acceleration has its liquid surface inclined 45° . Determine its acceleration.? An open rectangular tank 3.8 m high, 2.5 m wide and 6 m long is filled with water at a depth of 2.2 m. If the tank is accelerated at 2.3 m/s². Compute the maximum acceleration without spilling any water.