ISA 100 x 75 x 10 mm (cross-sectional area = 1650 mm-) Serves as a tensile member. This angle is welded to a gusset plate along A and B appropriately as shown. Assuming the yield strength of the steel to be 260 N/mm². ISA (100 × 75 × 10 mm) B Gusset base With reference to the information given, Determine Area of connected leg Area of outstanding leg i Net effective area of the member

ISA 100 x 75 x 10 mm (cross-sectional area = 1650 mm-) Serves as a tensile member. This angle is welded to a gusset plate along A and B appropriately as shown. Assuming the yield strength of the steel to be 260 N/mm². ISA (100 × 75 × 10 mm) B Gusset base With reference to the information given, Determine Area of connected leg Area of outstanding leg i Net effective area of the member

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Similar questions

an angle bar 100x100x11 mm tension member is connected with 20-mm-dia bolts as shown in the fig. both legs of the angles are connected. use fy=248 MPa and Fu=400 MPa. 1. determine the nominal strength for tensile yielding in the gross section. a. 515.59 kN b. 429.67 kN c. 545.60 kN d. 390.10 kN 2. determine the effective net area of member a. 1573 mm^2 b. 1632 mm^2 c. 1605 mm^2 d. 1815 mm^2 3. determine the nominal strength for tensile rupture in the net area. a. 642 kN b. 730 kN c. 554 kN d. 650 kN
Determine: Ix & ly = Moment of inertia about axis XX and YY Rx & Ry = Radius of gyration about axis XX and YY Sx & Sy = Elastic modulus about axis XX and YY steel specs are here http://www.toolsforengineer.com/steel-sections-properties-tables/ FOR WIDE FLANGE = W250X22FOR ANGLE BAR = L32X32X6.4
Determine the tensile capacity of a 200 x 100 x 12 mm angle in S275 steel assuming that the angle is connected through the longer leg by one row of M24 bolts (Fig. 3). (3 bolts in a row and p = 70 mm)
5. a bolted lap joint shown in the figure below. The bolts are 20m in diameter in 23 mm holes. The plates are 12m thick X350 Allowable stress of Plates: Tenaion in gross area0.60Fy Tension in net area0.50 Fu Shear on Net Area 0.30Fu Yield Strength of plate, Fy 248 Npa Ultinate tensile strength of Plate. Fu400 Mpa x, Find the safe load P based on a- Gross area yielding b. net area rapture c. block shear 2 of 3
The small postal scale consists of a counterweight W1, connected to the members having negligible weight. Determine the weight W2 that is on the pan in terms of the angles θ and Φ and the dimensions shown. All members are pin connected.
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 The figure below is a bracket which fastened by a bolts with a diameter of 0.5 inch. Compute the corresponding shear stresses. Assume single shear. Note: Round off your answer in two decimal places.
Continuing the solution of the given problem, find the required tie wire in kilograms if the reinforcements are space at: a.Vertical bars spaced at 80 cm and one horizontal bars atevery 3 layers of the block. b.Vertical bars at 60 cm and one horizontal bar at every after2 layers of the block. c.Tie wire in kilograms. (30 cm) Attached are the previous solutions
Determine the nominal tensile strength of the single angle. Consider 7/8" diameter bolt and A242 steel with Fy = 50 ksi and Fu = 70 ksi. L6x6x3/4 d = 6 in. b = 6 in. t = 0.75 in. k = 1.25 in. wt./ft. = 28.8 plf. A = 8.46 in.^2 x = 1.77 in.
TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
Determine the Net Area for the following Plate Section consider all possible Cases. The Plate thickness is 1-in. and the bolts' diameter is 7/8-in. s = 6.0 " g = 2.0 "
The figure shows a truss and the detail of the riveted connection at joint H. Using allowable stresses ofτ = H MPa and σb= I MPa, how many 19-mm diameter rivets are required to fasten member HB to thegusset plate? Member HC? Round-up your answer to a whole number F=162 H=110 I= 180