King Arthur tries to remove a cylindrical hollow metal rod attached to a wall at one end by rotating it at 25 rad/s counter clockwise using a power of 1.10 kW. The rod has an inner and outer diameter of 15 and 30cm respectively. The length is 900 mm. What is the maximum shear stress in kPa, is experienced by the hollow rod?

King Arthur tries to remove a cylindrical hollow metal rod attached to a wall at one end by rotating it at 25 rad/s counter clockwise using a power of 1.10 kW. The rod has an inner and outer diameter of 15 and 30cm respectively. The length is 900 mm. What is the maximum shear stress in kPa, is experienced by the hollow rod?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An open tank 3m by 3m in horizontal section weighs 4 kN and contains water to a depth of 1m. It is acted by an unbalanced force of 18 kN parallel to the pair of sides. a) Determine the acceleration of the tank. b) What must be the height of the tank so that no water will spill out? c) If the acceleration is increase by 4m/s2 , how much water will spill out?
gage pressure at point 1 = 275 kPa velocity = 3 meters/sec *Neglect friction* Given the figure, determine the total longitudinal thrust applied on the horizontal pipe.
An open horizontal tank, 1.5m high, 2m wide, and 5m long is full oil (sp gr=0.9. it is accelerated in the direction parallel to the longer length at 2.3m/s^2 a) what is the force acting at the wall of the tank with the shortest depth in kN b) if the acceleration is increased by 0.88m/s^2, find the volume of oil spilled out
The power transmission cable in the figure below weighs 165 N/m. Using the table below, write down the numerical value of w. If h= 2.5m, determine the resultant horizontal and vertical forces the cable exert on tower BD.
A sliding gate 3m wide by 1.60 m high is in a vertical position. The coefficient of friction between the gate and guides is 0.20. If the gate weigh 18 kn and its upper edge is 10 m below the water surface, what vertical force is required to lift it? Neglect the thickness of the gate.
1. A Vertical semicircular area of radius r = 100cm is submerged and has its diameter in a liquid surface. Determine (a) total force acting on one side and (b) its location from the liquid surface.2. Determine (a) the magnitude and (b) location of the total hydrostatic force acting on the 2m x 4m gate shown in Figure.
A two-dimensional converging duct is being designed for a high-speed wind tunnel. The bottom wall of the duct is to be flat and horizontal, and the top wall is to be curved in such a way that the axial wind speed u increases approximately linearly from u1 = 100 m/s at section (1) to u2 = 300 m/s at section 2. Meanwhile, the air density ? is to decrease approximately linearly from ?1 = 1.2 kg/m3 at section (1) to ?2 = 0.85 kg/m3 at section (2). The converging duct is 2.0 m long and is 2.0 m high at section (1). (a) Predict the y-component of velocity, ?(x, y), in the duct. (b) Plot the approximate shape of the duct, ignoring friction on the walls. (c) How high should the duct be at section (2), the exit of the duct?
An open can of water is subjected to an upward acceleration of 4.50 m/s2. What is the pressure at a depth of 1.50 m?
A horizontal bend in a pipeline conveying 1m^3/s of water gradually reduces from 600mm to 300mm in diameter and deflects the flow through an angle of 60 degrees. At the larger end, the pressure is 170kN/m^2. Determine the magnitude of the force exerted on the bend.
An open tank 1.82m square contains 1m of water. It is translated horizontally to the right at an acceleration of 3m/s2. a) How high should the tank be such that no water will be spilled? b) If the acceleration is now 5m/s2 and the height of the vessel is the answer in (a), how much water will be spilled? c) If the vessel is initially closed at the top and accelerated to the right at 5m/s2, what will be the hydrostatic force acting on the left side of the vessel?
A sector-shaped sluice gate having a radius of curvature of 5.4 m is as shown. The center of curvature C is 0.9m vertically below the lower edge A of the gate about which the gate is constructed to turn. If the water level is 2.4m above the lower edge of the gate (a) Determine the magnitude (in kN) and direction (R or L) of the horizontal component of the force acting on the curved gate AB. (b) Determine the magnitude (in kN) and direction (U or D) of the total vertical component of the force acting on the curved gate. Determine the magnitude of the total force (in kN) acting on the gate. Determine the angle that the total force acting on the gate makes with the horizontal.
An inclined circular gate with a diameter of 3.9 meter has water on one side. Calculate the gate's total hydrostatic force in Kn. a = 4.8 meters