Please answer correctly.Q.34 A 20 hp, 230 V, 1150 rpm DC shunt motorhas four poles, four parallel armature paths and882 armature conductors. The armature circuitresistance is 0.188 12.At rated speed and rated output, the armaturecurrent is 73 A and field current is 1.6 A.Calculate the electromagnetic torque.

Given V=230V P=20hp Ia=73 A Four pole, four parallel paths

lease answer correctly. 34 A 20 hp, 230 V, 1150 rpm DC shunt motor as four poles, four parallel armature paths and 82 armature conductors. The armature circuit sistance is 0.188 12. t rated speed and rated output, the armature urrent is 73 A and field current is 1.6 A. alculate the electromagnetic torque.

lease answer correctly. 34 A 20 hp, 230 V, 1150 rpm DC shunt motor as four poles, four parallel armature paths and 82 armature conductors. The armature circuit sistance is 0.188 12. t rated speed and rated output, the armature urrent is 73 A and field current is 1.6 A. alculate the electromagnetic torque.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given: shunt generator, efficiency=92%, %VR=5, shunt field current=3.1A, armature resistance= 0.125 Ω. Find the rated power and the required shunt field resistance
A 200V long-shunt generator delivers 100A, has an armature resistance of 0.050, a series field resistance of 0.250 and a shunt field resistance of 2000. If a brush contact drop of 2.5V IS considered, what will be the developed power inside the armature of the machine?
An 8-Pole, simplex lap wound, shunt generator has 800conductors and a flux per pole of 0.025Wb and running at 1200rpm. The armature and shunt field resistances are 0.25Ω and 120Ω respectively. If the armature voltage drop is equal to 10V, what is the load current (in Amp)? use two decimal places if the answer is not exact and do not include the unit anymore.
A shunt motor, supplied at 250 V, runs at 900 r/min when the armature current is 30 A. The resistance of the armature circuit is 0.4 Ω. Calculate the resistance required in series with the armature to reduce the speed to 600 r/min, assuming that the armature current is then 20 A.
Your Answers may be presented through Discussions, Drawings/Figures/Diagrams, Reference to NEC/PEC and Computations 4. Which NEC table is used to determine the full-load current of a torque motor?
A belt-driven 150 kW shunt wound DC generator is running at 500 rpm and is supplying full load to a bus bar at 230 V. At what speed will it run if the belt breaks and the machine continue to run taking 10 kW from the bus bar? The armature and the field resistances are 0.05 Ohm and 100 Ohms respectively. The brush contact drop is 150 Volts per brush. Neglect armature reaction.
3) The total Armature Winding resistance and shunt area winding resistance of a self-excitation DC shunt motor0.22 Ω and 170Ω respectively. Motor armature coefficient Ka = 40. DC shunt motor, a mechanical loadit operates at 230V for feeding and is powered by a full load current of 40A. Flux per polethe value is known to be 50mWb. Brush-contact voltage drop is 2V. Core losses andthe total loss of Rotary parts is 450W. Answer the following. (a) Armature current value (b) induced voltage value in Armature (c) the speed of the Motor,
A shunt generator us connected to a load that draws 8.8 kW, Ra= 0.04 ohms and Rsh=. 48 ohms. If the power developed in the armature is 106.3% of the power delivered to the load, determine the terminal voltage of the generator. A 15 kW, 230 V shunt generator was run light as a motor to determine its stray power losses at rated load . The applied voltage across the armature computed for test was 254 V and the armature current drawn is 2 A. The armature and shunt field resistances are 0.25 and 100. ohms, respectively. Calculate the generator efficiency at half load. Assume stray power losses to be constant. A shunt generator supplies 100 A at 200 V. The armature and shunt resistances are 0.025 ohms and 100. ohms respectively. If the copper losses are equal to the iron losses at this load, find the brake horsepower of the engine driving the generator.
Q3)A DC shunt generator has avoltage on open circuit of 150V. When machine is on load, the terminal voltage is 135V. Find the ratio between two speeds at no load and load condition (discuss the results). Assume emf induced remains unaltered. Field resistance 15(ohms), and armature resistance 0.02(ohms). Ignore the saturation. Neglect brush contact drop.
2. A 10-HP, 1,750 rpm 550-volt shunt motor has an armature resistance of 1.55 ohms. If the armature takes 14.8 amp at full load, calculate the following: the counter emf developed by the motor, volts? the power developed by the motor, Watts?
An 6-pole d.c. shunt generator with 850 Lap wound-connected armature conductors and running at 1200 r.p.m supplies a load of 13 Ω resistance . The armature resistance is 0.28 Ω. The field current is 1.13 A, the induced e.m.f. is 243V. Determine the load current, load voltage, armature current?
D.C. Shunt generator runs at 400 rpm and delivers 500 KW to bus-bars having a constant voltage of 400V. Assuming the field excitation to be constant at 5A, Calculate the speed at which the generator must run if the load on it is to be reduced to 300KW. The armature resistance is 0.0150?