Let's begin by determining the equilibrium position of a seesaw pivot. You and a friend play on a seesaw. Your mass is 90 kg, and your friend’s mass is 60 kg. The seesaw board is 3.0 mm long and has negligible mass. Where should the pivot be placed so that the seesaw will balance when you sit on the left end and your friend sits on the right end?

Let's begin by determining the equilibrium position of a seesaw pivot. You and a friend play on a seesaw. Your mass is 90 kg, and your friend’s mass is 60 kg. The seesaw board is 3.0 mm long and has negligible mass. Where should the pivot be placed so that the seesaw will balance when you sit on the left end and your friend sits on the right end?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.3DP

See similar textbooks

Similar questions

4. Use Geogebra and the Klein-Beltrami model to show that a pentagon with five right angles and a hexagon with six right angles can be drawn in hyperbolic geometry. Hint: Start with two lines that have a common perpendicular.Find the poles of those two lines, then draw an appropriate line through each pole, so on.
Recall the discussion on spacecraft from the chapter opener. The following problems consider a rocket launch from Earth’s surface. The force of gravity on the rocket is given by F(d)=−mk/d2, where m is the mass of the rocket, d is the distance of the rocket from the center of Earth, and k is a constant. 172. As the rocket travels away from Earth’s surface, there is a distance D where the rocket sheds some of its mass, since it no longer needs the excess fuel storage. We can write this function as F(d)=⎨(−m↓1 k / d^2) if d < D (−m↓2 k / d^2) if d ≥ D Is there a D value such that this function is continuous, assuming m1≠m2?
Hello, I need your help. Topics: Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation, Moment of a Force-Vector Formulation, and Principle of Moment. Note: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. Thank you so much.
counterweight is 200g, goal is to shoot a 7g clay ball 3 meters. B) Find velocity vector of the clay ball if you think there not enough information to solve. You can make up a value to solve it.
JUST DRAW THE SCHEMATIC DIAGRAM. NO NEED TO SOLVE. THANK YOU In Rizal province, one of its power plants has been thoroughly monitored for possible conversion into a wind power plant. A propeller wind turbine is to be used. Survey showed that Rizal Province at a height of 10 meters above the ground has a minimum wind speed of 7.1 miles per hour duringthe month of June and a maximum wind speed of 12.9 miles per hour during the month of January. The minimum temperature is at 75 degree Fahrenheit during the month of January and maximum temperature is at 89 degree Fahrenheit during the month of May. The existing power plant has an output of 54MW. For the proposed wind power, the power coefficient of turbine is 35% and the generator efficiency is 95%. Theimpeller diameter is assumed not to exceed 90m. Determine the following:a. Theoretical Wind Power Outputb. Electrical Power Outputc. Number of turbines to be installed
The title of our study is "Design and Fabrication of an Agricultural Spraying Attachment for an Autonomous Rover" we need help in the machine design part of our study, specifically Pump selection, battery selection, and center of gravity computation I already sent you the image of the rover Rover weight capacity 35 kilo grams (payload) Rover measurements: Wheel distance - 14.5 inches and 8.5 inches Rover platform size (width & length) 14.4 inches x 10.4 inches Height- 15.8 inches. Water tank selection More or less 25 liters *For tank selection we need to justify the size with the center of gravity, proving that is the maximum dimension or liters of the tank because the center of gravity will be higher making the rover prone to toppling Pump selection *Our sprayer design has two nozzles which splits using a tee splitter, we need to find the size of the pump to obtain the same discharge rate of a normal sprayer. A normal sprayer has a 12V pump and a pressure from 0.2 to 0.45 mpa…
Read the question carefully and give me right solution according to the question. Use Superposition method.
Come up with a problem and solve it using these information below.
Please help me solve the question in the picture below using matlab
solve the question with explanation asap and I'll give you multiple upvotes
As an automotive engineer, your role is to design a petrol engine for SUV car with fourstroke and four cylinder petrol engine. Describe the performance criteria need to beconsidered in detailing out the possible outcome of your spark ignition engine? Write asimple essay and an example of your design calculation to describe the prototype ofyour engine.
Need help with these Q2. Identify any zero force members. ( there can be more than one ) Member AB Member AJ Member BCBC Member BH Member BJ Member CD Member CG Member CH Member DE Member DF Member DG Member EF Member FG Member GH Member GJ q3. You are asked to find the forces in members GHGH and CGCG using the Method of Sections. Which members should you make a cut through? Member AB Member AJ Member BC Member BH Member BJ Member CD Member CG Member CH Member DE Member DF Member DG Member EF Member FG Member GH Member GJ Q4. Having made a cut through the members in the previous part, you next want to solve for Member GH. Which of the following equilibrium equations is the most efficient? (i.e. which one will allow you to solve for the required member in one equation?) a. ΣFx=0. b. ΣMC=0. c. ΣMH=0. d. ΣFy=0 e ΣMD=0