Liquid methanol is fed to a space heater at a rate of 12.0 L/h and burned with excess air. The product gas is analyzed and the following dry-basis mole percentages are determined: CH3OH = 0.45%, CO2 = 9.03% and CO = 1.81%. (a) Draw and label a flowchart and verify that the system has zero degrees of freedom.  (b) Calculate the fractional conversion of methanol, the percentage excess air fed, and the mole fraction of water in the gas product

Q: Output variable response to a unit step input is given in Figure 1. a) Calculate the time constant o...

A: a. Time constant is the time required for the response y(t) to reach 63.2% of its ultimate value (ma...

Q: A dead-weight gauge measures a pressure of 40 mmHg. If the local barometric pressure is 69 cmHg, wha...

A:  

Q: If a 0.2800g sample of sodium bicarbonate (96.5% NaHCO3) is titrated with 0.9165N Sulfuric acid, wha...

A: We are asked to find the volume of the acid required to produce the end point. given, the mass of so...

Q: Make a table as required in the illustrated example with commentary on the amount of heat transfer l...

A: Given: m=3.416 h=11W/m2K   (Taking SI units as proper units are not given in question) k=377 W/mK  (...

Q: Draw Newman projections to show all the major conformers of bromoethane. Predict which one is lowest...

A: To do draw Newman projections to show all the major conformers of bromoethane predict the one lowest...

Q: 3. An urban sludge basin has a volume of 500 m3. The basin is initially 64% full. The sludge with a ...

A: The volume of the sludge basin, V = 500 m3 Density of sludge, ρ = 1320 kg/m3 The rate at which basin...

Q: The combustion of C3H6 to CO2 and H2O can be described by any of the reactions:C3H6 + 9/2 O2 → 3 CO2...

A:

Q: Calculate the volumetric flow value of the oil flowing through the pipe, such as shown in the figure...

A: Given, Height of the manometer, h = 4 in acceleration due to gravity, g = 32.2 ft/s Calculate the ve...

Q: In a pharmaceutical plant, a copper pipe (kc=400 W/mK) withinner diameter of 20 mm and wall thicknes...

A: Given:-

Q: The manufacturers of a new oatmeal product want to determine the least expensive way to safeguard an...

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question...

Q: What is the % v/v of 10.0 mL of CH3OH (methanol) dissolved in water to a volume of 40.0 mL?

A:

Q: Consider a hemispherical droplet of liquid water residing on a flat surface, as shown in the figure....

A: Given data: The vapor pressure of water at 40 0C (pA1) = 0.073 atm Diffusion coefficient of water va...

Q: If an uncovered pot of boiling water has a vapor pressure of 12 psi in Denver, what is the atmospher...

A: Answer: 12 psi

Q: The flow rate through the pipe is 14999 L/hr. The pipe is new commercial steel pipe with an internal...

A:

Q: A steam power plant uses 10 tons of coal per hour to produce electricity.If in the power generation ...

A: Given:- mass flow rate = 10 tonn of coal per hour                Temperature =  500°C,              ...

Q:

A: To Find the the correct option that gives the correct description of alkaline error associated with ...

Q: Explain the reaction of Ethene with Bromine water?

A: When ethene reacts with bromine water 1,2 dibromoethane is formed. The reaction is used as a test fo...

Q: The system equations for two liquid surge tanks inseries are A₁dh′₁/dt=q′i−1/R₁h′₁,q′₁=1/R₁h′₁ A₂dh′...

A: The system equations are A1dh1'dt=q1'-1R1h1'        ........(1)A2dh2'dt=1R1h1'-1R2h2'        ..........

Q: 1. What mass of methane (CH4) must be burned to release -185 kJ of heat? CH4(g)+ 2O2(g)→CO2(g)+ 2H2O...

A: Given: CH4(g) + 2O2(g) → CO2(g) + 2H2O(l)              △H=-890.4 kJmolIt is required to find the mas...

Q: Necesito ayuda

A: Volume of N2 = 25 litres Pressure = 200 atm Dimension of laboratory = 5 * 5*3 m3  

Q: The vapour pressure and molar volume of water as function of temperature are given below: T, K 49...

A: (a) Write the Clapeyron equation as follows: P2-P1 = ∆Hvap∆VlnT2T1             ......(1) Since we ha...

Q: 1)Define what is meant by polarity in covalent bonds 2) Is HCI a polar or non polar molecule? Explai...

A: 1.) Polar covalent bonding is a type of chemical bond where a pair of electrons are unequally shared...

Q: The pH of a fruit juice is 4.2. Find the hydronium ion concentration, H,0* of the juice. Use the for...

A:

Q: An ideal Rankine cycle operates with the following design: 100 kg/s of steam enters the turbine at 3...

A:

Q: Determine the amount of steam to be consumed, the economy, and the heating area required, for the pr...

A: Feed with flow rate F flows through the evaporator and water(pure) evaporates at flow rate of V and ...

Q: In a pharmaceutical plant, a copper pipe (kc=400 W/mK) with inner diameter of 20 mm and wall thickne...

A:

Q: Classify each molecule as polar or nonpolar.

A:   CO32- = Non-polar Using VSEPR or Lewis structure rationale, carbonate (CO32- ion) ion is non-polar...

Q: For the reaction:CO(NH2)2 (aq) + H2O (l) → CO2 (g) + 2NH3(g)The ∆S° and ∆H° is 354.8 J/K•mol and 119...

A:

Q: The vapor pressures of heptane (substance 1) and octane (substance 2) are as follows: Temp(°C) va...

A: Given that, Temperature T = 110oC Vapor pressure of heptane at 110oC p1vap = 1047 mm Hg Vapor pressu...

Q: Give four challenges and suggest solutions for those challenges in Butterfly valve

A: Our objective is to write the challenges and the solutions for those challenges in butterfly valve.

Q: 3.) Convert the information given in the table below from the U.S. customary units to SI units. U.S....

A:

Q: What is the pressure (in bar) of a sample of N2H4 gas with a density of 2.15 g/L at 298 K?

A:

Q: 1.5 mol of methane gas, which behaves ideally, with a pressure of 10 bar and a temperature of 300 K,...

A: Given: Process; Isothermal expansion Temperature (T) = 300 K (constant throughout the system) Number...

Q: The exhaust duct from a heater has an inside diameter of 114.3 mm with ceramic walls 6.4 mm thick. T...

A: Given data: Inside diameter = 114.3 mm Ceramic walls 6.4mm, the average k = 1.52W/mKThermal conducti...

Q: Water at 50 ° C is converted into superheated steam at 170 ° C with a pressure of 170 kPa. Specify: ...

A:

Q: In calibrating a 50 mL buret, a student found that 50 mL of water measured from the buret at 21oC we...

A: Given: Volume showed by burette = 50 mL Weight measured (W) = 49.9381 gram

Q: 1.35 kg is suspended by a A sphere with diameter D = 0.12 m and mass m = jet of air as shown below. ...

A: Given data: Diameter of the sphere = 0.12 m Mass of the sphere = 1.35 kg Drag coefficient fro the sp...

Q: 7.) The czpnduction heat transfer rate through a wall is modeled by the following equation: Q = k4AT...

A:

Q: Choose an appropiate process,which involves heat,work and energy conversion explain the process

A: It is required to explain a process which involves heat, work, and energy conversion.

Q: At very high temperatures, which heat transfer mechanism is dominant? Explain. b) Explain the mechan...

A: Hi and thanks for the question. Since you have posted multiple questions and have not specified whic...

Q: When 0.625 grams of ethanol (62H5OH) undergoes combustion in a bomb calorimeter attaining a temperat...

A: Ans; Given  mole of ethanol =0.625 gTemprature difference =2.8∘CHeat capacity of calorimeter = 5.17 ...

Q: 12.) An individual running on a treadmill machine generated an average power of approximately 0.27 h...

A: