Load Analysis: A floor beam is used to support the 3-m width of a reinforced concrete slab having a thickness of 120 mm. The slab serves as a portion of the ceiling for the floor below and it’s bottom is coated with plaster. Furthermore, a 2.75-m high, 12.5-cm thick lightweight solid concrete block wall is directly over the top flange of the beam. The cross-sectional area of the wide flange steel beam is 36,645 mm2. Determine the total dead load carried by the steel beam (expressed in k

Load Analysis: A floor beam is used to support the 3-m width of a reinforced concrete slab having a thickness of 120 mm. The slab serves as a portion of the ceiling for the floor below and it’s bottom is coated with plaster. Furthermore, a 2.75-m high, 12.5-cm thick lightweight solid concrete block wall is directly over the top flange of the beam. The cross-sectional area of the wide flange steel beam is 36,645 mm2. Determine the total dead load carried by the steel beam (expressed in k

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Bucket: 8.5 lbBucket + concrete: 58.7 lbVolume: 0.265 ft3Density of Concrete: _____________lb/ ft3ASTM DESIGNATION: _____________
What is the amount of loadthat applied to the center ofthe rectangular concrete beamsample if the Modulus ofRupture is 3.50MPa?Length of the sample = 550mmDimension: 150mm x150mm
One way slabs 12 shown in Fig.1 is composed of three panels and supported by brick wall. Given: fc'= 28 Mpa, fy=400 Mpa, L = 5230 mm, thickness of Tilling and mortar =0.034 m, Live load = 2.42 KN/m, Find slab thickness
A rectangular footing 2.1 m x 3.6 m x 0.35 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 346 kN LL = 231 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA. Answer: 1.83
30) A rectangular footing 2.1 m x 3.6 m x 0.35 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 346 kN LL = 231 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
A rectangular footing 2.3 m x 3.6 m x 0.38 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL= 306 kN LL = 241 kN Li Pc = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA
How to conduct compression test. Discuss from thebeginning to end using your own words.Whatare needed for compression test?
1. Concrete Hollow Block 200mm H x 400mm L x 150mm thk. per piece and Laying 8 layers x 4.5 meters excluding the doorway, is reinforced with 10mm diameter steel bars at every 3 layers horizontally and 0.80 meters on center spacing for vertical bars. a) What is the total area of the CHB installed or laid? A=? in square meters A = 7.20m3 b) How many blocks are required? N=? pieces Provide Wastage Factor = 3% N = 93 pcs c) How much mortar or grout is required in CHB laying? In cubic meters Answer: 0.5562 m3 d) How many bags of cement is needed if Class B Mixture is required? WF=3% Answer: 7 bags Answers are already given, solutions are needed.
a rectangular footing 2.3 m x 3.3 m x 0.31 m thick supports a 300 mm square column at its center. column loads are service conditions:DL = 385 kN LL = 292 kN f'c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm calculate the nominal punching shear stress in the slab. write your final answer with 2 decimal places if the unit is MPA.
a 300 mm thick footing slab supports a 300 mm thick concrete wall carrying uniform service dead load of 214.31 kN/m and service live load of 145.94 kN/m. the base of the wall footing slab is 1.2 m from the ground surface. design parameters are as follows: ysoil = 16 kN/m^3, yconci = 24 kN/m^3. qa = 215.46 kPa. f'c = 27 MPa and fy = 420 MPa. 1. calculate the required center to center spacing of 16 mm bars for flexure if the maximum factored moment in the slab is 75 kN.m a. 150 mm b. 180 mm c. 210 mm d. NOTA 52. calculate the ultimate beam shear stress on the footing slab if the footing slab is 2.1 m wide. a. 1.25 MPa b. 0.74 MPa c. 0.87 MPa d. 0.96 MPa
Determine: 2Z1 + 5Z2 show solutions with steps asap
GIVE 10 DISADVANTAGES OF USING HOLLOW BLCOKS.