load voltage and input impedance

Q: Voltage Output (Vo)

A: The diode is conducts when it is forward bias mode. In the reverse bias mode the diode  doesn't…

Q: For the Phase-Shift oscillator, determine the oscillator frequency C, = C2 = C3 = C = 0.001 µF R2 =…

A:

Q: Find the input impedance Zin (in Ohm)

A: Assumptions:…

Q: demodulation circuit of transmission of digital signal ask

A: ASK - The term ASK stands for Amplitude shift keying. it is a subtype of Amplitude Modulation. ASK…

Q: Define on-off ratio. Why series JFET has higher on-off ratio as compared to shunt JFET? Answer:

A: JFET - Junction field-effect transistor  JFET can be both series JFET and shunt JFET

Q: true or false The drop-off rate for low and high frequency regions is (-6 dB/octave) if the…

A: Ans. false

Q: Find tha value of the output voltage.

A: Referring to the circuit diagram, redrawing the circuit by marking the inverting and non-inverting…

Q: Q#4: What is ripple voltage in capacitor-Input filter, under what conditions the filtering action is…

A:

Q: Defermine z-Transfurm including region* Cunteryence in

A: The given signal x[n] is

Q: The input impedance of a FET   a. approaches zero   b. is impossible to predict   c.…

A: In this question,  Choose the correct option The input impedance of a FET?

Q: Without bypass capacitor Cg, determine input impedance Zi CE EMITTER-BIAS CONFIGURATION 0 22 V 3,3…

A:

Q: RC phase-shift oscillator circuit, for sustained state of oscillation, the phase shift around the…

A: in this we find phase shift in rc oscillator..

Q: Convert

A:

Q: Fill in the Blank: Z, is the input impedance that not practically shows infinite length of a

A: Zo is the input impedance that not practically shows infinite length of a

Q: Series compensation is commonly used in  Low-voltage AC transmission systems.   Select one: True…

A: The method by which the voltage of the system is increases is known as the series compensation. This…

Q: The phase shift between the input signal and the output signal of Buffer(voltage follower) is…

A:

Q: In which class of chopper, the output current is always positive, whereas the output voltage could…

A: In class D chopper output current is always positive but output voltage either positive or negative.…

Q: Determine Vo 20 V -5 V

A:

Q: in Frequency response, the voltage gain of an amplifier varies with signal .............

A: Frequency response is graph which describes voltage gain of amplifier with frequency.

Q: Why is the input impedance to a JFET so high?

A: Consider the n-channel JFET shown in the figure below,

Q: junction. Select one: OTrue O False

A: In this question, given in reverse bias, a pn  junction voltage attracts the majority carriers…

Q: -H) Gyla) Speed etrol input Speed GA Temsion contrel input Tension

A: Here i have solved it using massons gain formula.

Q: In Digital Storage Oscilloscope ,input signal is applied to the amplifier and attenuator section.…

A:

Q: compare between coherent and incoherent demodulation

A:

Q: A O 505L 100S 50 В о

A: The given circuit is:

Q: Impedance

A: Given, Vin = 100 volt Vin = 100 volt and Iin = 22 volt

Q: DC and AC analysis

A:

Q: If Aol = 3500 and Acm = 0.35, the CMRR is *

A: In an op-amp circuit, when at positive and negative terminal of op-amp signal is applied without any…

Q: Which of the following circuits oscillate?) For each circuit, state the reason for your ans Voo Voo…

A: Given the following circuits as shown below: We need to find which circuit oscillates. Let…

Q: 1. Draw the AC equivalent circuit of the voltage divider bias configuration below with emitter…

A: As per our company guidelines we are supposed to answer only first 3 subpart kindly repost the other…

Q: Power amplifiers

A: In this question , we will write about power amplifier...

Q: Determine the input and output impedances with feedback for voltage shunt having A = 100, B = 0.1…

A:

Q: Compute total current.

A: The solution can be achieved as follows.

Q: Single slope ADC  gives highest conversion rate. Select one: True False

A:

Q: Elashing DC genretu.

A: In this question we will write about generator field flashing...

Q: 2- For Zeigler-Nichols method the gain.. is increased till system oscillates at constant amplitude…

A: according to question we have to discuss gain in zeigler- nichols method.

Q: if you design differentiator to differentiate input signal varies in frequency between 1 KHz and 20…

A: A cut off frequency magnitude response is 3 dB lower 0 Hz. Formula cutoff frequency :  fc = 1(2π RC…

Q: 2- If capacitor =0.1 micro farad and feedback resistance=1.6 k ohm then Corner frequency =.......KHz…

A: Corner frequency (also known as Cut off frequency) is the frequency at which the frequency response…

Q: write about: The Band stop filter Definition 200 words do not write in handwritten and DO NOT COPY…

A:

Q: The correct term for the instrument pulling out current from the source is: load compensation…

A: Ideally voltmetmeters should have infinite resistance and ammeters should have zero resistance  But…

Q: Determine the output voltage Vo

A:

Q: =10 μA

A:

Q: 17.21 Determine the output voltage of the regulator show below (IADI = 50UA). +24 Vo LM317 +VOUT R1…

A:

Q: VERTICAL CONTROLS • POSITION - • SCALE (Volts per Division) – • BANDWIDTH LIMIT – • INPUT COUPLING –…

A:

Q: In Digital Storage Oscilloscope ,input signal is applied to the amplifier section only. Select one:…

A: The block diagram of Digital oscilloscope: The block diagram of the digital storage oscilloscope…

Q: For a second order system, natural frequency of oscillation is 10 rad/sec and damping ratio is 0.1.…

A: In this question,  We need to determine the settling time for the 2%.  We know  2% settling time =…

Q: Calculate the theoretical value of the output impedance

A: Given :    Small signal AC model we have to short circuit all the DC sources and we need to short…

Q: For the Phase-Shift oscillator, determine the oscillator frequency C, = C2 = C3 = C = 0.001 µF R2 =…

A: The given circuit is the RC phase shift oscillator. The feedback segment of the oscillator is given…

Q: Determine output on 37

A: In this question we need to find a output of the given logic circuit

Z parameter

The Z-parameters that are the impedance parameters of a two-port network are defined by expressing the two-port voltages V1 and V2 in terms of two-port currents I1 and I2. The Z-parameters are calculated by open circuiting one of the two ports at a time henceforth they are called open-circuit impedance parameters.