Answered: Marin factors tend to reduce the…

Marin factors tend to reduce the strength; stress concentration factors tend to increase the stress. Therefore, both tend to increase the factor of safety.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter7: Tubing And Piping

Section: Chapter Questions

Problem 2RQ: The size of 1/2 in. would refer to the ______regard to copper tubing used in plumbing and heating....

See similar textbooks

Similar questions

prove the law temperature fin is : θ(x)=C1eax +C2e-ax
(Solid Mechanics) This plate is clamped into a wall is subjected to a force F as shown. The wall does not generate any stress concentration. At the fillets the stress concentration factor is given Kt = 1.5 (No need of using charts). The plate is made of a cast iron with the following properties:Modulus E=150 GPaTensile strength Sut =200 MPaCompressive strength Suc=600 MPaWhere and how could the plate fail and at which force Fmax?
Need help starting this assignment. 1- Determine the maximum normal stress, the maximum shear stress, the Modulus of Elasticity, the maximum bending moment and the maximum stress due to bending (also known as flexure stress) on the material, from the information provided. 2- From the results of your analysis, determine what material was used for this test. Check whether the material can withstand the different types of loading the hip implant experiences. Use a factor of safety of 4.
Which steel presents the maximum modulus of toughness UT? UT = ( (Sy − Sut) /2 ) ε f AISI 4142 and AISI 1020 AISI 1020 AISI 1095 and AISI 1020 AISI 4142 and AISI 1095
6. Oxygen used in oxy-acetylene metal cutting was stored in a tank (empty tank weight is 25lb) whose volume is 48ft3. Initially, the gauge pressure reading of the tank was 40psi. After usage, the pressure reading falls to 25psi. Determine the final weight (lb) of the tank after the operation if the temperature in the tank remains constant at 77°F. Draw a figure or FBD that will support the problem. Explain each step by step formula.
Which of the following conditions/factors will reduce a materials fatigue resistance: Select one or more: a.Experiencing a permanent residual compressive stress b.Increasing the stress amplitude c.Experiencing a mean tensile stress d.Roughening or etching the surface e.Mechanically hardening the surface
Questions(a) Explain what is meant by the terms: terile stress and Young's modules.Define the quantity which relates these terms. (b) When measuring Young's modulus of a material it is common to use aspecimen which is (1) very long and (ii) very thin. Give the reasons for this. Describe, with a labelled diagram, how you would measure accurately theextension of such a wire under an applied load. (e) The graph below shows how the extension of a wire varies with the loadapplied to it. The wire used has a length of 3m and a diameter of 5 x 10^-4m i. Calculate the tensile stress produced by a load of 50N.ii. Find the energy stored in the wire when the load is acting.iii. Calculate the reduction in gravitational PE of a 5kg mass used to providethe load.iv. Calculate Young's modulus for the metal of the wire.
Ductile materials have more impact strength compared to brittle materials. Select one: True False
9=Which of the following materials has the highest toughness value? A) Bakır Cupper B) Alüminyum Aluminum C) Titanyum Titanium D) Dökme demir Cast iron E) Magnezyum Magnesium
The type of fluctuating stress in which the mean stress is zero and variable stress is equal to maximum stress is called ____________________________. choose one completely reversed fatigue stress alternating fatigue stress fluctuating fatigue stress repeated fatigue stress
pllllllllllllease solve question 8
Choose the right answer: a)The lower the quality of the surface finish, the less of area of a contact will have corrosion b)High quality finished surface increases wear resistance c)Strength of interference fits factor is not related with a condition of surface d)Having a scratches on surface increase the fatigue strenght