Material Strengths: Fy = 248 MPa, Fu = 400 MPa Method: Use ASD. A single angle L127X89X19 is welded (longitudinal and transverse welds) on one leg (shorter leg) togusset plate; thus, there are no holes. The length of the longitudinal welds is 150 mm. Which of the following most nearly gives the allowable tensile load?

Material Strengths: Fy = 248 MPa, Fu = 400 MPa Method: Use ASD. A single angle L127X89X19 is welded (longitudinal and transverse welds) on one leg (shorter leg) togusset plate; thus, there are no holes. The length of the longitudinal welds is 150 mm. Which of the following most nearly gives the allowable tensile load?

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter28: Filler Metal Selection

Section: Chapter Questions

Problem 4R: What chemicals alloys are a. considered to be contaminants to the weld metal? b. used to increase...

See similar textbooks

Similar questions

9. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi i) what is the weld capacity of the shear connection in kips? (2 decimal places)
The design below is used for a bridge construction. All parts of the assembly are made of ASTM A36 steel and are welded with an E60 electrode. Under these conditions, the minimum size weld, according to table 20-4, should be: 5/16 3/16 3/8 1/4 1/2 5/8
A U-groove weld is used to butt weld 2 pieces of 7.0-mm-thick titanium plate. The U-groove is prepared using a milling cutter so the radius of the groove is 3.0 mm. During welding, the penetration of the weld causes an additional 1.5 mm of material to be melted. The final cross-sectional area of the weld can be approximated by a semicircle with a radius of 4.5 mm. The length of the weld is 200 mm. The melting factor of the setup is 0.57 and the heat transfer factor is 0.86. (a) What is the quantity of heat (in Joules) required to melt the volume of metal in this weld (filler metal plus base metal)? Assume the resulting top surface of the weld bead is flush with the top surface of the plates. (b) What is the required heat generated at the welding source?
An RSW operation is used to join two pieces of sheet steel having a unit melting energy of 8369.85 J/cm3. The sheet steel has a thickness of 0.3125 cm. The weld duration will be set at 0.25 sec with a current of 11,000 amp. Based on the electrode diameter, the weld nugget will have a diameter of 0.75 cm. Experience has shown that 40% of the supplied heat melts the nugget and the rest is dissipated by the metal. If the electrical resistance between the surfaces is 130 micro-ohms, what is the thickness of the weld nugget assuming it has a uniform thickness?
The welding parameters to be used to butt weld a metal alloy are being evaluated. In order to set up the welding machine, the melting factor for the metal (f2) has to be determined. The welding machine can deliver 4000 watts of power and the heat transfer factor for the welding process (f1) is 0.9. The final weld bead consists of 8 0% filler metal and 40% parent metal. The melting temperature of the filler metal and the parent metal is the same 2540 deg F. The cross-sectional area of the weld bead is 0.5 sq inches. The rate at which filler metal is added to the weld is 1 cu inch per min. Conversion factor 1 Btu = 1055 J and 0 deg F = 460 deg R Calculate the melting factor.
Can a tee weld be strong if the welds on both sides do not have deep penetration? Why or why not?
What chemicals alloys are a. considered to be contaminants to the weld metal? b. used to increase tensile strength in the weld metal? c. used to increase corrosion resistance? d. used to reduce creep?
According to Practice 15-6, after each weld pass the test plate should be allowed to cool but never allowed to cool below what temperature?
Does all of the heat produced by an SMA weld stay in the weld? Why or why not?
What is the maximum plate thickness that an FCS weld can be made with 100% penetration without beveling the joint?
When estimating weld cost, what weld joint design factors should be considered?
What would be the transverse shear strength per inch of weld if a specimen that was 2.5 in. wide withstood 25,000 lb?